Cisco Meraki MX64W Manual de usuario

MX64W Installation Guide

This document describes how to install and set up the MX64W security

appliance. Additional reference documents are available online at:

www.meraki.com/library/products.

MX64W Overview

The Meraki MX64W is an enterprise security appliance designed for

distributed deployments that require remote administration. It is ideal for

network administrators who demand both ease of deployment and a

state-of-the-art feature set. This appliance provides the following new

features:

• USB port, to support approved 3G/4G cards for failover to cellular

networks.

• Support for four LAN connections

• Wall screws and anchors for mounting drywall surface, either

vertically or horizontally

Package contents

In addition to the MX64W, the following are provided.

The MX64W front panel

Status Indicator

The MX64W uses an LED to inform the user of the device's status. LED patterns and their meanings are described

below.

LED Status Meaning

Solid orange Power is applied but the appliance is not connected to

the Meraki Dashboard

Alternating Colors The appliance is attempting to connect to Meraki

Dashboard

Flashing White Firmware upgrade in progress

Solid White Fully operational

The MX64W back panel

Additional functions on the back panel are described below, from left to right.

USB port USB 2.0 for 3G/4G wireless cards. Traffic status is

indicated by the USB LED.

LAN ports

These 4 ports provide connectivity to computers,

printers, access points, or Ethernet switches.

A steady green LED indicates bidirectional connectivity,

and flashing green indicates traffic.

The LAN4 port can either be a LAN port or a second

Internet port.

WAN / Internet port Provides connectivity to the WAN.

eset button

Insert a paper clip if a reset is required.

• Press for 1 second to delete a downloaded

configuration and reboot.

• Press and hold for more than 10 seconds to force a

full factory reset.

Power input Designed for use only with the unit’s power supply.

The MX64W bottom panel

Please note that the serial number is located on the product label at the bottom panel of MX64W

Mounting hardware

The supplied wall screws and anchors allow you to mount the appliance on a drywall surface, either vertically or

horizontally. The distance between the holes you drill should be 5-1/8 inches (13 cm).

• For mounting on drywall, use a ¼-in drill bit, then insert the plastic and screw assemblies.

• For mounting on wood or a similar surface, use only the screws.

• Allow the heads of the screws to stick out far enough to be inserted securely into the back of the appliance.

Connecting to WAN

All Meraki MX devices must have an IP address. This section describes how to configure your local area network before

you deploy it. A local management web service, running on the appliance, is accessed through a browser running on a

client PC. This web service is used for configuring and monitoring basic ISP/WAN connectivity.

Setting up a static IP address

To ensure that the client PC is redirected to the local web service in the following step, you must disable all

other network services (ex: wi-fi) on your client machine.

Do the following to configure basic connectivity and other networking parameters:

1. Using a client machine such as a laptop, connect to one of the four LAN ports of the MX.

2. Using a browser on the client machine, access the appliance's built-in web service by browsing to

http://setup.meraki.com. (You do not have to be connected to the Internet to reach this address)

3. Click Uplink configuration under the Local status tab. The default credentials use the device serial number as

the username, with a blank password field.

4. Choose Static for the IP Assignment option.

5. Enter the IP address, subnet mask, default gateway IP and DNS server information.

Setting up a DHCP IP address

By default all MX devices are configured to DHCP from upstream WAN / ISP servers. Simply plug the MX's WAN /

Internet port to your upstream circuit and wait a few minutes for the unit to negotiate a DHCP address.

Additional settings

Setting VLANs

If your WAN uplink is on a trunk port, choose VLAN tagging > Use VLAN tagging and enter the appropriate value for

VLAN ID for your network.

Setting up secondary WAN interface (dual WAN)

You can toggle the LAN4 port between LAN and Internet, through Uplink configuration under the Local status tab.

Setting PPPoE

PPPoE authentication may be required if you are connecting MX device to a DSL circuit. You need to know your

authentication option and credentials (supplied by your ISP) in order to complete these steps.

• Choose Connection Type > PPPoE.

• Select your Authentication option.

• If you select Use authentication, enter appropriate values for Username and Password.

Web proxy settings

These settings take effect if the MX device has to fall back to using HTTP to contact the Cloud Controller. By default,

web proxy is disabled. To enable web proxy, do the following:

When the WAN connection is fully enabled, Internet LED 1 will turn green.

Please note that all these settings below are accessible only via the local management console.

• Choose Web proxy > Yes.

• Enter values as appropriate for Hostname or IP and Port.

• If you require authentication, choose Authentication > Use authentication, and enter appropriate values for

Username and Password.

Configuring physical link settings

To configure physical link settings on the Ethernet ports, click Local status > Ethernet configuration. You can enable

half duplex, full duplex, and autonegotiation, as well as set 10- or 100-Mbps data rates.

To apply all configuration settings to the appliance, be sure to click Save Settings at the bottom of the page.

Tabla de contenidos

Otros manuales de Cortafuegos de Cisco

Cisco

Cisco Meraki MX64 Manual de usuario

Cisco

Cisco RV110W Manual de usuario

Cisco

Cisco ASA 5506-X Manual de usuario

Cisco

Cisco ASA 5585-X Manual de usuario

Cisco

Cisco Firepower 4100 Series Manual de instalación

Cisco

Cisco RV110W Manual de usuario

Cisco

Cisco Firepower 4100 Series Manual

Cisco

Cisco PIX 506E - Security Appliance Manual de usuario

Cisco

Cisco PIX 520 - PIX Firewall 520 Manual de usuario

Cisco

Cisco ASA 5506-X Instrucciones de instalación

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual de usuario

Cisco

Cisco ASA 5512-X Manual de usuario

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual

Cisco

Cisco RV110W Manual de usuario

Cisco

Cisco Small Business RV215W Manual de usuario

Cisco

Cisco ASA 5506-X Guía de inicio rápido

Cisco

Cisco MEREAKI MX65W Manual de usuario

Cisco

Cisco Firepower 4110 Manual de usuario

Cisco

Cisco FirePOWER 7000 Manual de usuario

Cisco

Cisco Firepower 9300 Manual

Cisco

Cisco FPR1010-ASA-K9 Manual de usuario

Cisco

Cisco Small Business RV220W Manual de instrucciones

Cisco

Cisco 2100 Series Manual de usuario

Cisco

Cisco Firepower 7010, Firepower 7020, Firepower 7030, Firepower 7050, Firepower 7110, Firepower 7120, Firepower 7115, Firepower... Manual de usuario

Manuales populares de Cortafuegos de otras marcas

Fortinet

Fortinet FortiGate Voice Series Manual de usuario

ADTRAN

ADTRAN NetVanta 2300 Manual de usuario

SecureLogix

SecureLogix ETM System Manual de usuario

NETGEAR

NETGEAR ProSafe FVX538 Manual de usuario

Lanner

Lanner FW-8877 Manual de usuario

Huawei

Huawei USG6000 Series Manual de instalación y operación

H3C

H3C SecPath F5000-AI-15 Manual de usuario

Nexcom

Nexcom DNA 1150 Manual de usuario

Fortinet

Fortinet FortiGate-60 series Manual de usuario

Draytek

Draytek Vigor2860 Series Manual de usuario

Lanner electronics

Lanner electronics FW-7650 Series Manual de usuario

Swisscom

Swisscom Internet Backup Manual de usuario

SonicWALL

SonicWALL NSa 5700 Manual de usuario

DPtech

DPtech FW1000 SERIES Manual de usuario

FEITIAN

FEITIAN MultiPass FIDO Manual de usuario

EBLOCKER

EBLOCKER PRO Manual de usuario

GTA

GTA GB-200 Manual de usuario

Trend Micro

Trend Micro Deep Edge Manual de usuario