Central Pneumatic 93656 Manual de usuario

AIR PIN NAILER

ASSEMBLY and OPERATING

INSTRUCTIONS

Model 93656

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit ourWeb site at http://www.harborfreight.com

of this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

SKU 93656 Page 2For technical questions, please call 1-800-444-3353.

Pin Size 23 Gauge, 1/2” to 1” long, Headless pins

Magazine Capacity 100

Operating PSI 60-100 PSI

Air Inlet Size 1/4” NPT Male

Safety Feature Single Sequential Safety Trip Mechanism

Accessories Two Hex Wrenches, Lubricating Oil,

1,500 Fasteners: 500 each - 5/8”, 3/4”, & 1” Pins

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instruc-

tions, operating and maintenance procedures, parts list and diagram. Keep your invoice with

this manual. Write the invoice number on the inside of the front cover. Keep the manual and

invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be

followed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in damp or wet

locations. Do not expose to rain. Keep work area well lit. Do not use electrically powered

tools in the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do not let them

handle machines, tools, extension cords, or air hoses.

4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit

rust. Always lock up tools and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or attachment to do

the work of a larger industrial tool. There are certain applications for which this tool was

designed. It will do the job better and more safely at the rate for which it was intended.

Do not modify this tool and do not use this tool for a purpose for which it was not intended.

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving

parts. Protective, electrically nonconductive clothes and nonskid footwear are

recommended when working. Wear restrictive hair covering to contain long hair.

7. Do not overreach. Keep proper footing and balance at all times. Do not reach over or

across running machines or air hoses.

8. Stay within air pressure capacity.Never operate the Nailer above 90 PSI.

9. Hold tool away from head and body. During operation the Nailer may kick back causing

injury.

SKU 93656 Page 3For technical questions, please call 1-800-444-3353.

10. Use eye and ear protection. Always wear ANSI approved impact safety goggles

and appropriate hearing protection. Wear a full face shield if you are producing

metal filings or wood chips. Wear an ANSI approved dust mask or respirator

when working around metal, wood, and chemical dusts and mists. Other people

in the work area must also wear ANSI approved impact safety goggles.

11. Maintain tools with care. Keep tools clean for better and safer performance. Follow

instructions for lubricating and changing accessories. Inspect tool cords and air hoses

periodically and, if damaged, have them repaired by an authorized technician.The handle

must be kept clean, dry, and free from oil and grease at all times. Do not operate a tool if

any portion of the tool’s operating controls are inoperable, disconnected, altered or not

working properly.

12. Disconnect Air Hose and release any built-up air pressure. Never service the Nailer,

clear jams, or disassemble with the air hose attached. Always release any built-up air

even after disconnecting hose. Disconnect the Nailer when not in use.

13. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are

removed from the tool or machine work surface before attaching to an air source.

14. Avoid unintentional starting. Be sure the trigger is in the Off position when not in use

and before plugging in. Do not carry any tool with your finger on the trigger, whether it is

attached to an air source or not. Do not point the tool towards yourself or anyone whether

it contains fasteners or not.

15. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when

you are tired.

16. Check for damaged parts. Before using any tool, any part that appears damaged should

be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment and binding of moving parts; any broken parts or mounting

fixtures; and any other condition that may affect proper operation.Any part that is damaged

should be properly repaired or replaced by a qualified technician. Do not use the tool if

the trigger does not operate properly.

17. Guard against electric shock. Prevent body contact with grounded surfaces such as

pipes, radiators, ranges, and refrigerator enclosures.

18. Replacement parts and accessories. This product is to be repaired and serviced only

by a qualified technician. When this product is serviced, only identical replacement parts

should be used. Use of any other parts will void the warranty. Only use accessories

intended for use with this tool. Approved accessories are available from Harbor Freight

Tools.

19. Do not operate tool if under the influence of alcohol or drugs. Read warning labels

if taking prescription medicine to determine if your judgement or reflexes are impaired

while taking drugs. If there is any doubt, do not operate the tool.

20. Use proper size and type extension cord. If an extension cord is required, it must be of

the proper size and type to supply the correct current to the compressor without heating

up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage

to the tool. Check your air compressor’s manual for the appropriate size cord. It is also

possible that the use of an extension cord may cause your circuit breaker to trip or your

SKU 93656 Page 4For technical questions, please call 1-800-444-3353.

panel fuse to break. If this happens, either use the compressor without an extension

cord or find a larger amperage circuit to use.

21. Maintenance. The maintenance outlined in the maintenance section should be performed

regularly. For your safety, this product should be serviced or repaired regularly only by a

qualified technician.

22. Compressed air only. Use clean, dry regulated, compressed air at 90 PSI. Never use

oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source

for this tool.

23. Do not load pins with the trigger or safety depressed. Unintentional firing

may occur. Do not load nails when the air hose is connected to the tool. Always

assume that the tool contains fasteners.

24. Disconnect air supply before loading Nailer. Before reloading (or making any

adjustments to) the Nailer make sure that the compressed air is disconnected.

25. Fire fasteners into an appropriate work surface only. Do not attempt to fire fasteners

into surfaces too hard to penetrate. Do not drive fasteners on top of other fasteners, or at

too steep of an angle. Fasteners can ricochet causing personal injury. Never fire the

Nailer into the air, or point it toward yourself or another person. Always wear ANSI

approved safety goggles during use, maintenance, and reloading.

26. Do not fire fasteners too close to the edge of a workpiece. They may split the

workpiece and fly free, causing personal injury.

27. Take caution as some woods contain preservatives such as copper chromium

arsenate (CCA) which can be toxic. When stapling or nailing these materials extra

care should be taken to avoid inhalation and minimize skin contact.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities, contain chemicals known [to the State of California] to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or other masonry products

• Arsenic and chromium from chemically treated lumber

(California Health & Safety Code § 25249.5,

et seq.

)

28. Transport Nailer safely. Always disconnect air supply when moving the tool in the

workplace. Carry the tool by the handle and avoid contact with the trigger.

Note: Performance of the compressor (if powered by line voltage) may vary depending on

variations in local line voltage. Extension cord usage may also affect tool performance.

Warning:The warnings, cautions, and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must be understood

by the operator that common sense and caution are factors which cannot be built into

this product, but must be supplied by the operator.

SKU 93656 Page 5For technical questions, please call 1-800-444-3353.

Testing the Single Sequential SafetyTrip Mechanism

Warning: Even though the nailer should be empty during this procedure, ALWAYS point

the nailer at a piece of scrap wood when testing.

1. Make sure the tool is disconnected from the power supply.

2. Completely empty the magazine of pins.

3. The Nailer should not fire if the nose is not depressed against the workpiece.

4. Check that the Trigger (42) and the Safety (48) move freely, without sticking - see

Figure

, next page.

5. Connect the air supply to the tool at the Air Inlet (22) set at the recommended 60-100

PSI, and not to go over the maximum 100 PSI.

6. Test the tool by depressing the Safety (48) against the workpiece without pulling the

Trigger (42). The tool must not cycle (fire). If it cycles (fires), stop immediately and

take the tool to an authorized service technician.

7. Hold the tool away or off of the workpiece. The Safety (48) of the tool should return to its

original position. Squeeze the Trigger (42). The tool should not cycle (fire). If it cycles

(fires), stop immediately and take the tool to an authorized service technician.

8. Depress the Safety (48) against the workpiece and squeeze the Trigger (42). The tool

must cycle (fire). Release the trigger and squeeze it again. The tool must cycle (fire).

With the Trigger held, carefully lift the nailer and press it against the workpiece again.

The tool must not cycle (fire). If it fails to act in the manner described in bold, have it

repaired by a qualified service technician.

Unpacking

When unpacking, check to make sure the parts listed on page 9 are

included. If any parts are missing or broken, please call Harbor Freight Tools at

the number on the cover of this manual as soon as possible.

Operation

For best service, you should incorporate an oiler, regulator, and inline filter, as shown in

the diagram below. Hoses, couplers, oilers, regulators, and filters are all available at Harbor

Freight Tools.

Note: To connect this tool, we recommend a quick coupler/adapter (not included). Coupler/

adapters are available at Harbor Freight Tools. If an automatic oiler is not used, put 3-5

drops of pneumatic tool oil in the Air Inlet (22) before each use.

Nailer

SKU 93656 Page 6For technical questions, please call 1-800-444-3353.

Operating the Nailer

1. Attach the Nailer to the air supply at the Air Inlet (22). Start your compressor and check

the pressure making sure it is set at the recommended 90 PSI and not to go over the

maximum 90 PSI.

2. To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if the

nose is not depressed. Once depressed, gently and briefly squeeze the Trigger (42)

once. Do not fire repeatedly. Pins could bounce off of one another, damaging the work

piece or causing PERSONAL INJURY.

Loading Pin Nails

ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN

RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other

people in the work area must also wear ANSI approved impact safety goggles.

Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool.

1. Press the Magazine Latch (23) up and slide the Magazine (57) back.

2. If you are using a different pin length than previously:

a. Remove all pins from inside the nailer.

b. Slide the Pin Length Selector (64) to the appropriate length setting. See

Figure 1

3. Holding the nailer upside-down, insert the pin nails into the slot noted above.

4. Close the Magazine (57) making sure the Magazine Latch (23) clicks shut.

See

Figure 1

Operation (continued)

FIGURE 1

Air Inlet

(22)

Magazine (57) Safety

(48)

Trigger (42)

Magazine

Latch (23)

Insert

Pins Here

Pin Length

Selector (64)

SKU 93656 Page 7For technical questions, please call 1-800-444-3353.

Anytime

any

maintenance or repairs are done (including clearing jams), FIRST:

1. Disconnect the Nailer from the air hose.

2. Empty the Magazine (57) completely.

3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected

and is incapable of firing any pins.

4. Always leave the Magazine (57) open during maintenance. The Magazine is

spring-loaded and may cause parts or a nail to fly out of the Nailer.

Clearing Jams

1. Disconnect tool from air hose, empty the

Magazine (57) of pins, release any built-up air

pressure, and leave the magazine open, as

explained above.

2. Hold the Nailer pointed away from you and any

other people or fragile objects. Remove the Short

Cap Screw (47) and the two longer Cap Screws

(46) - see

Figure 2

. Remove the Safety Cover

(45) and Safety Spring (49) and set them aside.

3. Remove the Safety Guide (50) carefully to avoid

bending the Safety (48) - see

Figure 3

4. Remove the jammed pin. Pliers may be

necessary to remove a stuck pin.

5. Inspect the Driver (11) for bends or breakage -

see location in

Figure 4

. If it is damaged, do not

use the tool until it is repaired by a qualified

technician.

6. Lightly oil the Driver (11). Replace the Safety

Guide (50) underneath the Safety (48). The

Safety (48) should fit perfectly into the groove in

the Safety Guide (50). See

Figure 3

7. Replace the Safety Spring (49) onto the Safety

(48) as in

Figure 3

. Carefully place the Safety

Cover (45) over the Safety and Spring and

attach using the Cap Screws (46) and the Short

Cap Screw (47) - see

Figure 2

. Make sure that

the Short Cap Screw (47) goes in the correct

position. Make sure that the Safety (48) is spring

loaded and moves freely, without sticking.

8. Reload the Nailer and reconnect it to the air hose.

9. Press the Safety (48) of the Nailer against an

appropriate piece of scrap wood.

10. Test fire the Nailer several times, checking for

proper operation.

11. Disconnect the Nailer, remove the pins and store

it in a location out of children’s reach.

FIGURE 2

Short Cap

Screw (47)

Cap

Screws (46)

Safety

Cover (45)

FIGURE 3

Safety (48)

Safety

Spring (49)

Safety

Guide (50)

Driver

Guide (54)

FIGURE 4

Safety (48)

Driver (11)

Driver

Guide (54)

SKU 93656 Page 8For technical questions, please call 1-800-444-3353.

Anytime

any

maintenance or repairs are done, FIRST:

1. Disconnect the Nailer from the air hose.

2. Empty the Magazine (57) completely.

3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected

and is incapable of firing any pins.

4. Always leave the Magazine (57) open during maintenance. The Magazine is

spring-loaded and may cause parts or a nail to fly out of the Nailer.

ediuGgnitoohselbuorT

.ruccosmelborpgniwollofehtfoynafiyletaidemmireliaNdarBehtgnisupotS .naicinhcetdeifilauqaybylnoenodebts

umstnemecalpertrapdnasriapeR

.naicinhcetdeifilauqaebylnodetpmettaeboteratrahcsihtnodlobniserudecorpllA

melborPesuaCylekiLnoituloS

.aerareggirTtagnikaelriA gnisuohevlaVreggirTnisgniR-O .degamadera ytefaskcehcdna

sgniR-OecalpeR .noitarepopirt

.esoNdnagnisuoHneewtebgnikaelriA .gnisuoHniswercsesooL .)21(repmuB/sgniR-Od

egamaD .swercsnethgiT .)21(repmuBrosgniR-OecalpeR

.metSevlaVreggirTtagnikaelriA .degamaderaslaeSrosgniR-O .slaeSrosgniR-OecalpeR

.paCdnagnisuoHneewtebgnikaelriA .)1(paCrednilyCesooL.)1(paCrednilyCnethgiT

.ssolre

wopsahroylwolssnuR .liotneiciffusnI .dekcolbsi)81(tsuahxE .detcurtsnisaetacirbuL .strapdegamadecalpeR

.lia

naspiksreliaN

degamadro)21(repmuBnroW .gnirpSrehsuP .)45(ediuGrevirDnitriD .reliaNotwolfriaetauqedanI .not

siPnogniR-OyrdronroW reggirTnogniR-OdegamaD .evlaV

rehsuPro)21(repmuBecalpeR .gnirpS .)45(ediuGrevirDnisle

nnahCnaelC .sgnittifrosserpmocdnaesohkcehC .sgniR-OetacirbulroecalpeR .sgniR-OecalpeR

.demmajerasliaN

.nro

wsirevirdnoediuG .degamadroezisgnorwerasliaN eraswercsesoNroenizagaM .esool .degamadsi)11(revirD

.ediuGecalpeR .sliandegamadnu,tcerrocesU .swercsnethgiT

.)11(revirDecalpeR

.thgitnwodevirdtonlliwreliaN gnippils)11

(revirDdednuoR .nworclianffo .erusserpriafokcaL .rewopfossoldnagnilcycwolS

.)11(revirDecalpeR

.)ISP59-55(e

russerptcerrocylppuS .raelcsi)81(tsuahxEerusekaM

.ylpeedootliangnivirdedalB notsiPro/dna)21(repmuBnroW .r

ecapS .straphtobrorehtieecalpeR

.naicinhcetdeifilauqaebylnodetpmettaeboteratrahcsihtnodlobniserudecorpllA

SKU 93656 Page 9For technical questions, please call 1-800-444-3353.

NOTE: Some parts are listed and shown for illustration purposes only and are not available

individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM AND

TROUBLESHOOTING GUIDE IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE

MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTO

THE BUYERTHAT HE OR SHE IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR

SHE IS QUALIFIEDTO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/

OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE

UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER.THE BUYER

ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRSTOTHE ORIGINAL PRODUCT

OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF

REPLACEMENT PARTSTHERETO.

Parts List

traPnoitpircseDtraPnoitpircseDtraPnoitpircseD

1paCrednilyC42gnirpShctaL74wercSpaCtrohS

2gnir-O52niPgniniateR84ytefaS

3ev

laVnotsiP62eldnaH94gnirpSytefaS

4ralloC72gnir-O05ediuGytefaS

5gnir-O82gnir-O15wercSpaC

6gniRgniniL92gnir-O25wercSpaC

7gnir-O03e

vlaVreggirTrewoL35recapS

8gnir-O13gnirpS45ediuGrevirD

9rednilyC23laeS55wercSpaC

01gnir-O33gnir-O65rehsaWkcoL

11revirD43gnir-O7

5enizagaMrewoL

21repmuB53notsiPevlaVreggirT85niPlloR

31rehsaWelzzoN63laeS95revoCenizagaMraeR

41ydoB73gnir-O06rehsuP

51werc

SpaC83evlaVreggirTreppU16redloHgnirpS

61tuN93gnir-O26gnirpSrehsuP

71tekcarBgnitnuoM04regnulPreggirT36elacShtgneL

81rotcelfeDtsuahxE14tekcarBreggirT46rotceleShtgneLniP

91pilc-E24reggirT56enizagaMthgiRreppU

02retliF34wercSpaC66ediuGliaN

12p

aCdnE44niP76raBediuGliaN

22telnIriA54revoCytefaS86niP

32hctaLenizagaM64wercSpaC96enizagaMtfeLreppU

SKU 93656 Page 10For technical questions, please call 1-800-444-3353.

Assembly Drawing

Maintenance

Warning! Always disconnect the tool from the air compressor and then empty the magazine

of pins before attempting to inspect or perform maintenance to the Nailer.

1. Inspect all of the nuts and screws and make sure they are securely fastened.

2. Periodically lubricate the driving mechanism and magazine with a light oil. Wipe down

with a clean cloth. Never use gasoline or flammable solvents to clean the tool.

3. Inspect your air compressor according to manufacturer’s instructions.

Otros manuales para 93656

Tabla de contenidos

Otros manuales de Pistola de clavos de Central Pneumatic

Central Pneumatic

Central Pneumatic 68019 Manual de usuario

Central Pneumatic

Central Pneumatic Contractor 97524 Manual de usuario

Central Pneumatic

Central Pneumatic 69575 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 92917 Manual de instalación

Central Pneumatic

Central Pneumatic 68020 Manual de usuario

Central Pneumatic

Central Pneumatic 68019 Manual de instalación

Central Pneumatic

Central Pneumatic Contractor 97526 Manual de usuario

Central Pneumatic

Central Pneumatic 97525 Manual de usuario

Central Pneumatic

Central Pneumatic 93496 Manual de usuario

Central Pneumatic

Central Pneumatic 66902 Manual de instalación

Central Pneumatic

Central Pneumatic 93257 Manual de usuario

Central Pneumatic

Central Pneumatic Contractor Series Manual de usuario

Central Pneumatic

Central Pneumatic Contractor 97520 Manual de usuario

Central Pneumatic

Central Pneumatic 98751 Guía del usuario

Central Pneumatic

Central Pneumatic 68027 Manual de usuario

Central Pneumatic

Central Pneumatic 94446 Manual de usuario

Central Pneumatic

Central Pneumatic 68068 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 93909 Manual de instalación

Central Pneumatic

Central Pneumatic 4041 Manual de usuario

Central Pneumatic

Central Pneumatic Central Pneumatic Air Nailer/Stapler 2-in-1 Kit... Manual de usuario

Central Pneumatic

Central Pneumatic Professional 97512 Manual de usuario

Central Pneumatic

Central Pneumatic 41209 Manual de usuario

Central Pneumatic

Central Pneumatic 90193 Manual de usuario

Central Pneumatic

Central Pneumatic 68057 Manual de usuario

Manuales populares de Pistola de clavos de otras marcas

Performance Tool

Performance Tool M643 Manual de usuario

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco Fusion Technology F-35XP Manual de usuario

Grizzly

Grizzly G1847 Manual de usuario

Ryobi

Ryobi R18N18G Manual de usuario

Black & Decker

Black & Decker 492848-00 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manual de usuario

Metabo HPT

Metabo HPT NR 3690DC Manual de instrucciones

Surtek

Surtek CN650 Dimensiones y guía de instalación

Makita

Makita GF600 Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco AirFree 25 Manual de usuario

Freeman

Freeman P50LSLW Manual de usuario

Aicon PRO

Aicon PRO DAC4507 Manual de usuario

DAJ

DAJ XR150A Manual de usuario

Makita

Makita AN923 Manual de usuario

Grizzly

Grizzly T20644 Manual de usuario