Central Pneumatic 41164 Guía de referencia rápida

AIR HAND NAILER

41164

ASSEMBLY & OPERATING INSTRUCTIONS

REV07/01

THANKYOU for choosing a HARBOR FREIGHTTOOLS product. For future reference, please complete the

owner’s record below:

Model____________ Serial No._______________ Purchase Date _________________

SAVE THE RECEIPT, WARRANTY ANDTHESE INSTRUCTIONS. It is important that you read the entire

manual to become familiar with the unit BEFORE you begin assembly.

Technical Specifications

Tool Name:Air Hand Nailer

Item Number: 41164

Material: GravityAluminum

Air Nipple Material: Chrome Plated Steel

Tool Length: 5-1/4"

ToolWidth: 3-1/6"

Nail Length: 4"

OperatingPressure: 70 to 125 PSI *

AirConsumption: 8CFMnon-continuous

Driver Hardness: HRC 46 to 56

Air Inlet: 1/4" NPT Female

Warning: The warnings, cautions and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must

be understood by the operator that COMMON SENSE AND CAUTION ARE

FACTORS WHICH CANNOT BE BUILT INTO THIS PRODUCT, BUT

MUST BE SUPPLIED BYTHE OPERATOR.

The Operator

PLEASEREMEMBER:

Do not operate the product if under the influence of alcohol or drugs. Read warning labels on prescriptions to

determine if your judgment/reflexes might be impaired.

Do not wear loose clothing or jewelry as they can be caught in moving parts.

Protective gloves and non-skid footwear is recommended.

Wear restrictive hair covering to contain long hair.

Use eye and ear protection. Always wear ANSI approved impact safety goggles.

Maintain proper footing and balance at all times.

Keep hands away from firing part of the Nailer or serious injury may occur.

#41164 REV07/01 REV 11/06 Page 2

*The air pressure setting must not exceed job site regulations/restrictions. The air pressure setting

must not exceed 90 PSI when being used with work pieces that have a thickness of less than 1-3/4”.

Do not point Nailer at yourself, other people or pets.

Do not randomly shoot the Nailer into open space, as this may result in injury.

Work Area

TO AVOID RISK OF PERSONAL INJURY, EQUIPMENT DAMAGE, FIRE AND SHOCK, MAKE SUREYOUR

WORK AREA IS:

Free of damp, wet or rainy conditions

Free of flammable gasses or liquids

Free of children (never let them handle tools or machinery)

Well-lit

Clean and uncluttered

Well-ventilated

Before Operating

Before operating your Air Hand Nailer, check for damaged parts.

Never force the tool or attachment to do the work of a larger industrial tool. It is designed to do

the job better and more safely at the rate for which it was intended.

Do not try to use inappropriate attachments in an attempt to exceed the tool’s capacity. Approved accessories

are available from Harbor Freight Tools.

Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked

to determine that it will operate properly and perform its intended function.

Never drive fasteners on top of other fasteners as the fastener may deflect, resulting in injury.

Assembly

Your Air HandNailercomes completely assembled.

Air connection

Step 1) You will need a Union fitting (sold separately) before you can connect your Air

Hand Nailer to an air compressor. Attach the Union fitting to the Air Inlet and

tighten the fitting.

Step2) Attach an Air Coupler (sold separately) to the Union fitting if desired. This is a useful

accessory as it allows quick-coupling action when using a variety of tools with the same

aircompressor.

Set up

Frequent, but not excessive, lubrication is required for best performance. Oil added through the airline

connection will lubricate internal parts. An automatic airline oiler is recommended but oil may be added

manually before every operation or after about one (1) hour of continuous use. Only a few drops of oil at a time

are necessary. Too much oil will collect inside of the tool and be blown out during the exhaust cycle. Use only

Pneumatic tool oil. Do not use detergent oil or additives as these lubricants will cause accelerated wear to

#41164 REV 07/01 Page 3

Dirt and water in the air supply are major causes of pneumatic tool wear. Use a filter/oiler for better

performance and longer life of the tool. The filter must have adequate flow capacity for the specific application.

Set up (Cont’d)

Consultthe manufacturer’s instructionsforproper maintenance of yourfilter.

The connector on the tool must not hold pressure when the air supply is disconnected. If the wrong fitting is

used, the tool can remain charged with air after being disconnected and still be able to drive a fastener.

Operation

Please refer to the Parts List on pages 5 and the Assembly Diagram on page 6 prior to operation. It is

important that your read the entire manual to become familiar with the unit BEFORE you use it.

Step 1) Set the air compressor regulator to between 70 PSI and 125 PSI.

Step 2) Turn on the compressor.

Step 3) Connect the air line to the Air Plug (part #21).

Step 4) Grasp the fastener by the shaft and insert it into the Guide Bushing (part #20) as shown below

in Figure 1.

Warning: Never allow the point of any fastener to face your body, any other person or

animal, or any equipment that could be injured or damaged!

Step5) Holding the Nailer firmly, bring the point of the Fastener in to contact with the work

piece and firmly press down until the Guide Bushing (#20) is fully retracted into the Guide

Bushing Retainer (part #18). The Nailer will then begin nailing.

the seals in the tool.

Air Plug

#41164 REV07/01 REV 11/06 Page 4

Air Nailer

Step6) Lift the Nailer off of the work piece immediately after the fastener has been driven in.

Step 7) Upon completion of your job, disconnect the Nailer from the air supply. Turn off

the compressor.

Caution: Disconnect the Air Hand Nailer from the compressor hose before performing maintenance or

replacing parts.

Spring and Connector Replacement

If the Spring (part #17) begins to slip, you must replace the Guide Bushing (#18), Guide Bushing Retainer (#18),

andSealRing(part #19).

Step 1) Remove the Guide Bushing Retainer from theTool. Slide the Retainer off of the Guide

Bushing.

Step 2) Remove the Spring from the Nailer. Replace the Spring, Guide Bushing and

Guide Bushing Retainer. Securely tighten back into place.

Seal Ring Replacement

If air leaks from the unit, you will need to replace the Seal Ring (part #14). Take the following steps if you are

replacing the Seal Ring.

Step 1) Remove the four Hex Bolts (part #1) from the Exhaust Cover (part #2). Remove the Exhaust

Cover from the body (part #16).

Step #2) Remove the Seal Ring. It may involve some scraping for removal.

Step #3) Using the appropriate replacement Seal Ring (available through Harbor Freight Tools), replace

the worn Seal Ring with the new Seal Ring.

Step #4) Replace the Exhaust Cover and Hex Bolts. Tighten down securely.

IF THERE IS ANY QUESTION ABOUT ACONDITION BEING SAFE OR UNSAFE, DO NOT OPERATE THE TOOL.

Unpacking

UNPACK AND CHECK CONTENTS

When unpacking your Air Hand Nailer, check to make sure the following parts are included. If any parts are

missingorbroken,please call HARBOR FREIGHTTOOLS at1-800-444-3353.

Part # Description Quantity Part # Description Quantity

1 Hex Bolt 1 13 Pipe 1

2 Exhaust Cover 1 14 Seal Ring 1

3 O-Ring 2 15 O-Ring 1

4 O-Ring 1 16 Body 1

5 O-Ring 2 17 Spring 1

6 Main Piston Unit 1 18 Guide Bushing 1

7 Slide Cover 1 19 Seal Ring 1

8 O-Ring 1 20 Guide Bushing Retainer 1

9 O-Ring 1 21 Air Plug 1

10 Cylinder 1 22 Hook 1

11 Cylinder Sleeve 1 23 Washer 1

12 Bumper 1 24 Hex Bolt 1

#41164 REV 07/01 Page 5

Assembly Diagram-Air Hand Nailer

#41164 REV 07/01 Page 6

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE

MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR

WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE

ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR

DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS

REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED

TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND

LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR

REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION

OF REPLACEMENT PARTS THERETO.

Tabla de contenidos

Otros manuales de Pistola de clavos de Central Pneumatic

Central Pneumatic

Central Pneumatic 93656 Manual de usuario

Central Pneumatic

Central Pneumatic 68021 Manual de instalación

Central Pneumatic

Central Pneumatic 68247 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 68057 Manual de usuario

Central Pneumatic

Central Pneumatic 68020 Manual de usuario

Central Pneumatic

Central Pneumatic 92359 Manual de instalación

Central Pneumatic

Central Pneumatic 40115 Manual de usuario

Central Pneumatic

Central Pneumatic Contractor 97526 Manual de lista de piezas

Central Pneumatic

Central Pneumatic 93496 Manual de usuario

Central Pneumatic

Central Pneumatic 99640 Manual de instalación

Central Pneumatic

Central Pneumatic Contractor 97524 Manual de usuario

Central Pneumatic

Central Pneumatic 66872 Manual de usuario

Central Pneumatic

Central Pneumatic 4041 Manual de usuario

Central Pneumatic

Central Pneumatic 68023 Manual de instalación

Central Pneumatic

Central Pneumatic 44923 Manual de lista de piezas

Central Pneumatic

Central Pneumatic 69450 Manual de usuario

Central Pneumatic

Central Pneumatic 68068 Instrucciones de montaje

Central Pneumatic

Central Pneumatic 68022 Manual de instalación

Central Pneumatic

Central Pneumatic 97586 Manual de usuario

Central Pneumatic

Central Pneumatic Contractor Series Manual de usuario

Central Pneumatic

Central Pneumatic 92917 Manual de usuario

Central Pneumatic

Central Pneumatic 92917 Manual de instalación

Central Pneumatic

Central Pneumatic 68027 Manual de usuario

Central Pneumatic

Central Pneumatic Contractor 97520 Manual de usuario

Manuales populares de Pistola de clavos de otras marcas

Performance Tool

Performance Tool M643 Manual de usuario

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco Fusion Technology F-35XP Manual de usuario

Grizzly

Grizzly G1847 Manual de usuario

Ryobi

Ryobi R18N18G Manual de usuario

Black & Decker

Black & Decker 492848-00 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manual de usuario

Metabo HPT

Metabo HPT NR 3690DC Manual de instrucciones

Surtek

Surtek CN650 Dimensiones y guía de instalación

Makita

Makita GF600 Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco AirFree 25 Manual de usuario

Freeman

Freeman P50LSLW Manual de usuario

Aicon PRO

Aicon PRO DAC4507 Manual de usuario

DAJ

DAJ XR150A Manual de usuario

Makita

Makita AN923 Manual de usuario

Grizzly

Grizzly T20644 Manual de usuario