CALEFFI 2521 Series Guía del usuario

Function

The thermostatic mixer is used in solar thermal systems

producing domestic hot water. Its unction is to maintain the

temperature o the mixed water supplied to the user constant at

the set value when there are variations in the supply conditions

o the incoming hot and cold water. This particular series o

mixing valves can unction continuously at the high

temperatures o incoming hot water rom the solar storage tank.

The valve has been speci ically certi ied to ASSE 1017.

Product range

Series 2521 thermostatic mixing valve. Union thread NPT male

connections, sizes 1/2”, 3/4”,1”; union solder connection, size

1/2”, 3/4”, 1”.

Technical Characteristics

· Materials: - Body: Low‐lead brass

(<0.25% Lead content), chrome plated

- Shutter: PSU

- Springs: Stainless steel

- Seals: EPDM

· Setting range: 85–150°F (30–65°C)

· Accuracy: ±3°F (±2°C)

· Max working pressure (static): 200 psi (14 Bar)

· Max working pressure (dynamic): 75 psi (5 bar)

· Min working pressure (dynamic): 3 psi (0.2 bar)

· Max hot water inlet temperature: 212°F (100°C)

· Maximum inlet pressure ratio (H/C or C/H): 2:1

· Minimum temperature di erence between hot water inlet and

mixed water outlet or optimum per ormance: 30°F (15°C)

· Min. low rate to ensure stable temperature: 1.3 gpm (5 lpm)

· Certi ied to: ASSE 1017

· Lead Plumbing Law Compliance: (0.25% Max. weighted

average lead content)

· Lead Plumbing Law Certi ied by IAPMO R&T

Adjustable Thermostatic Mixing Valve for Solar Systems

2521 Series

28114.01

Installation, commissioning and servicing instructions

ASSE 1017

www.caleffi.com

CALEFFI

CAUTION: I the thermostatic mixer is not installed, commissioned and

maintained properly, according to the instructions contained in this

manual, it may not operate correctly and may endanger the user.

CAUTION: Make sure that all the connecting pipework is water tight.

CAUTION: I installing in an ASSE 1017 application, check valves shall

be used.

CAUTION: When making the water connections, make sure that the mixer

connecting pipework is not mechanically over-stressed. Over time this

could cause breakages, with consequent water losses which, in turn,

could cause harm to property and/or people.

CAUTION: Water temperatures higher than 100°F can be dangerous.

During the installation, commissioning and maintenance o the

thermostatic mixer, take the necessary precautions to ensure that such

temperatures do not endanger people.

CAUTION: In the case o highly aggressive water, arrangements must be

made to treat the water be ore it enters the thermostatic mixer, in

accordance with current legislation. Otherwise the mixer may be damaged

and will not operate correctly.

Leave this manual for the user.

SAFETY INSTRUCTION

This sa ety alert symbol will be used in this manual to draw attention to sa ety related

instructions. When used, the sa ety alert symbol means ATTENTION! BECOME ALERT!

YOUR SAFETY IS INVOLVED! FAILURE TO FOLLO THESE INSTRUCTIONS MAY

RESULT IN A SAFETY HAZARD.

CAUTION: All work must be per ormed by quali ied personnel trained in the

proper application, installation, and maintenance o systems in accordance

with all applicable codes and ordinances.

O erating Princi le

The controlling element o the solar thermostatic

mixing valve is a temperature sensor that is ully

immersed in the mixed water outlet passage. As

it expands or contracts, the sensor continuously

establishes the correct proportion o hot and

cold water entering the valve. The low is

regulated by a piston sliding in a cylinder

between the hot and

cold water passages.

Even when there are

pressure drops due to

the drawing o o hot or

cold water or other uses

or variations in the

incoming temperature,

the mixer automatically

regulates the water low

to obtain the required

temperature.

Flow curves

Kv = 2.6

0.2

∆p(psi)

G(l/min) (

gpm

)

(psi) (bar)

0.5

001

002

003

05

Cv = 3.0

.04

0.4

.04

0.4

COLD

HOT

MIX

COLD HOT

Ex loded diagram

Reg lating knob

Head fixing screw

Reg lating spindle

“O” Ring seal

Upper sh tter seat

Thermostatic element

Inner sh tter

“O” Ring

O ter sh tter

“O” Ring

Spring cover

Spring

Valve body

Union n t

Gasket

Tail piece body

Installation

Be ore installing a Cale i 2521 series mixing valve, the system

must be inspected to ensure that its operating conditions are

within the range o the mixer, checking, or example, the supply

temperature, supply pressure, etc.

Systems where the Cale i 2521 series mixing valve is to be

itted must be drained and cleaned out to remove any dirt or

debris which may have accumulated during installation.

Failure to remove dirt or debris may a ect per ormance

and the manu acturer's product guarantee.

The installation o ilters o appropriate capacity at the inlet

o the water rom main supply is always advisable.

In areas which are subject to highly aggressive water,

arrangements must be made to treat the water be ore it

enters the valve.

Cale i 2521 series mixing valve must be installed in accordance

with the diagrams in this manual, taking into account all current

applicable standards.

Cale i 2521 series mixing valve can be installed in any position,

either vertical or horizontal.

The ollowing are shown on the valve body:

- Hot water inlet, color red and marked “HOT”.

- Cold water inlet, color blue and marked “COLD”.

- Mixed water outlet, marked “MIX”.

It is essential that access to the valve is totally unobstructed or

any maintenance which may be required to the valve or

connections. The pipework rom/to the valve must not be used to

support the weight o the valve itsel .

Use

Thermostatic mixing valves are typically installed at the

outlet o hot water storage tanks in solar systems to ensure

constant temperature o the mixed water supplied to the end user.

Because o their low characteristics, the valves can be installed

to control the temperature or both single point o use and or point

o distribution. In order to guarantee the delivery o mixed water at

the set temperature, the 2521 series thermostatic mixing valves

must have a minimum low rate o 1.3 gpm.

Application Diagrams

COLD/BLUEHOT/RED

MIX

Key to symbols

Safety relief valve

Isolation and check valve

Isolation valve

Expansion vessel

Filter

HOT

COLD

MIX

MIN

HOT

COLD

CALEFFI

MIN

Normally closed

valve

Commissioning

A ter installation, the valve must be tested and commissioned in

accordance with the instructions given below, taking into account

current applicable standards.

1) Ensure that the system is clean and ree rom any dirt or debris

be ore commissioning the thermostatic mixer.

2) It is recommended that the temperature is set using a suitable

calibrated digital thermometer. The valve must be

commissioned by measuring the temperature o the mixed

water emerging at the point o use.

3) The maximum outlet temperature rom the valve must be set

taking account o the luctuations due to simultaneous use.

It is essential or these conditions to be stabilised be ore

commissioning.

4) Adjust the temperature using the adjusting knob on the valve.

For sa ety reasons, it is advisable to limit the maximum mixed

water temperature to 120°F in domestic hot water systems.

Setting the tem erature

The temperature is set to the required value by means o the

adjusting knob with the graduated scale on the top o the valve.

Preset locking

Position the handle to the number required. Unscrew the head

screw, pull o the handle and reposition it so that the handle its

into the internal slot o the knob. Tighten the head screw.

Maintenance

In service tests should be carried out regularly to monitor the

mixer per ormance, as deterioration o per ormance could

indicate that the valve and/or the system require maintenance. I ,

during these tests, the temperature o the mixed water has

changed signi icantly in comparison with the previous test, the

details given in the installation and commissioning sections

should be checked and maintenance carried out.

The ollowing aspects should be checked regularly to ensure that

the optimum per ormance levels o the valve are maintained.

Every 12 months at least, or more o ten i necessary.

1) Check and clean the system ilters.

2) Veri y that any check valves positioned upstream o the Cale i

valve are operating correctly, without problems caused by

impurities.

3) The Cale i valve should not be dismantled. Limescale can be

removed rom internal components by immersion in a suitable

de-scaling luid.

4) When the components which can be maintained have been

checked, commissioning should be carried out again.

Min 1 2 3 4 5 6 7 Max

81 90 100 111 120 127 136 145 152

Pos.

27 32 38 44 49 53 58 63 67

Troubleshooting

Under normal operating conditions the Cale i 2521 series mixing valve will provide a very

high level o per ormance. However, in some circumstances, where our maintenance plan is

not ollowed, the ollowing problems may arise.

Sym tom

Fluctuating mixed water

temperature

Erratic low o water rom

the valve

No low o water rom the

valve

Cause

a) Erratic supply temperatures

at the inlets o the valve.

b) Starvation o the water

supplies at the inlets

o the valve.

c) Incorrect commissioning

o the valve.

a) Insu icient water supplies.

b) Fluctuations in supply

pressures/temperatures.

c) Adverse e ect created

by other draw o points

on the system.

a) In-line ilters blocked.

Insu icient supply pressures.

c) Debris obstructing valve

operation.

Corrective action

·Restore inlet conditions

within the limits o the

valve.

·Stabilize inlet supply

conditions.

·Clean ilters.

·Restore inlet supplies.

·Clean debris or scale

rom valve.

Caleffi North America, Inc.

3883 est Milwaukee Road

Milwaukee, I 53208

T: 414.238.2360 F: 414.238.2366

CALEFFI

Safety

The thermostatic mixer must be installed by a licensed plumber in accordance

with national regulations and/or relevant local requirements.

I the thermostatic mixer is not installed, commissioned and maintained properly, according to the

instructions contained in this manual, it may not operate correctly and may endanger the user.

Make sure that all the connecting pipework is water tight.

When making the water connections, make sure that the mixer connecting

pipework is not mechanically over-stressed. Over time this could cause breakages, with

consequent water losses which, in turn, could cause harm to property and/or people.

Water temperatures higher than 100°F can cause serious burns.

During the installation, commissioning and maintenance o the thermostatic mixer, take the

necessary precautions to ensure that such temperatures do not endanger people.

In the case o highly aggressive water, arrangements must be made to treat the water be ore

it enters the thermostatic mixer, in accordance with current legislation. Otherwise the mixer

may be damaged and will not operate correctly.

Leave this manual for the user.

Tabla de contenidos

Otros manuales de Unidad de control de CALEFFI

CALEFFI

CALEFFI SATK40 Series Guía

CALEFFI

CALEFFI Z-one ZSR10 Series Manual de usuario

CALEFFI

CALEFFI 574 series Manual de usuario

CALEFFI

CALEFFI 200000 Manual de usuario

CALEFFI

CALEFFI Z-one ZVR10 Series Manual de usuario

CALEFFI

CALEFFI 2527 Series Manual de usuario

CALEFFI

CALEFFI LEGIOMIX 600094A Guía

CALEFFI

CALEFFI AIR190001 Manual de usuario

CALEFFI

CALEFFI 5213 Series Manual de usuario

CALEFFI

CALEFFI LEGIOMIX 6000 series Guía

CALEFFI

CALEFFI Z-one ZVR103 Manual de usuario

CALEFFI

CALEFFI 535H Series Guía del usuario

CALEFFI

CALEFFI 5218 Series Manual de usuario

CALEFFI

CALEFFI 524 Series Manual de usuario

CALEFFI

CALEFFI 573 Series Manual de usuario

CALEFFI

CALEFFI LEGIOMIX 6000 series Guía

CALEFFI

CALEFFI 574 series Manual de usuario

CALEFFI

CALEFFI 5261 Series Manual de usuario

CALEFFI

CALEFFI 676 Seies Manual de usuario

CALEFFI

CALEFFI 580011 Manual de usuario

CALEFFI

CALEFFI 5360 Series Manual de usuario

CALEFFI

CALEFFI 642 Series Manual de usuario

CALEFFI

CALEFFI Altecnic SATK40103 Guía

CALEFFI

CALEFFI 574 series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario