C.A. Technologies H2O-CPR-G Manual de usuario

HVLP/PRESSURE REDUCED AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS FLUID TIP

RANGE

*MAX GUN

INLET PRESS.

FOR HVLP

FAN

CONTROL

SCFM @

MAX GUN

INLET

STANDARD

IN CAT

PACK

AVAILABLE FLUID

NOZZLES TIPS

NEEDLES /

marking on needle

33-0208 0.8mm (.022") 40-1308 (308)

33-0210 1.0mm (.040") 40-1310 (310)

33-0212 1.2mm (.046") 40-1312 (312)

G, PPS 33-0213 1.3mm (.052") 40-1313 (313)

33-0214 1.4mm (.055") 40-1314 (314)

G, PPS 33-0215 1.5mm (.059") 40-1315 (315)

G, PPS 33-0217 1.7mm (.070") 40-1317 (317)

33-0219 1.9mm (.075") 40-1319 (319)

33-0222 2.2mm (.086") 40-1322 (322)

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4) H2O-CPR-G

*Note: Air cap test gages are available to confirm HVLP compliance.

H2O-CPR-G-PPS

*Gun inlet pressures may vary as required by application

13.5

H2O-CPR-G 60-1504 (S)

23-2101

CPR

(Pressure

Reduced)

23-1301

(HVLP)

0.8 - 1.7

0.8 - 2.2

29*

H2O-CPR-G

GRAVITY FEED SPRAY GUN

PRODUCT INFORMATION

Coating Atomization Technologies 337 South ArthurAvenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708

www.spraycat.com

The H2O-CPR-G gun comes equipped with both a pressure reduced air cap 23-2101 and a HVLP air

cap 23-1301 for areas requiring HVLP compliance.

23-2101 - consumes 11 cfm at 29 psi gun inlet.

23-1301 - consumes 13.5 cfm at 29 psi gun inlet.

23-2101 pressure reducedair caps can be used with the 0.8 mm - 1.7 mm fluid orifices listedbelow.

23-1301 HVLPair caps can be used with the full range of fluid orifices listed below.

Operation and Maintenance Instructions for H2O-CPR-G Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Screw the paint cup onto the gun’s gravity feed fluid inlet.

3.Fluid flowcan be controlledusingthe fluidcontrolknob, thisrestricts flowbylimitingneedletravel.It isbesttocontrol

fluid flow byproper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenanceis essential to insure proper gun operation.

Severalstates prohibitsprayingsolventinto the atmosphere and require the useofcovered gun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Removeaircap and clean separatelyusingclean solvent.

Clean the gravityfeed cup thoroughly, then spray clean solvent through the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Gun head disassembly and reassembly instructions:

Haverepair kit #10-105availablebefore gundisassembly.

Gun head disassembly

Toremovethenozzlecarrier (5) and aircap adapter (7):

1. Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body(3), and needle (16).

2.Removethe needlesealcartridge(17).

3. Loosenthe locknut (11) and remove fluidinlet (12)using a 11/16” open-end wrench.

4. The nozzle carrier (5) and air cap adapter (7) will now slide forward from the gun body (13).

Gun head reassembly

1. Install a new o-ring (4 & 8) on the air cap adapter (7).

2. Install the thread locknut (11) and seal (10) onto the fluid inlet (12) as far as possible.

3. Install a new fluid inlet seal (9) into the recess area on the nozzle carrier (5) inlet port.

4. Install carrier seal (6) onto the back of the nozzle carrier (5).

5. Slide the nozzle carrier (5) into air cap adapter (7) and insert into the gun body (13) as far as possible. Be sure the

nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (17) but do not tighten.

6. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the

body. While in this position, insert the fluid inlet (12) and tighten firmly.

7. Tighten the needle seal (17) to approx. 12 ft.-lb. torque.

8. Tighten the fluid inlet (12) to approx. 25 ft.-lb. torque.

9. Tighten the locknut (11) to approx. 33 ft.-lb. torque.

ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION

1See Air Cap Chart Air Cap** 19 60-2101 Trigger

2See Air Cap Chart Fluid Tip** 20 60-1520 Air Valve Assembly

333-1202 Fluid Nozzle Body 21 60-302 Air Valve Poppet

4 98-8026 O-Ring* 22 60-125 Seal*

560-J31H Nozzle Body Carrier 23 61-1003 Air Valve Spring*

6 60-123 Seal* 24 60-119 Seal*

760-34H Air Cap Adapter 25 60-201 Rear Bushing

860-131 O-Ring* 26 60-204 Needle Return Spring*

9 60-124 Seal* 27 60-205 Spring Seat*

10 60-130 Seal* 28 60-202 Fluid Control Knob*

11 60-118 Locknut 29 60-1510 Inlet Air Control (Optional)

12 60-127 Fluid Inlet 30 60-122 Plug

13 60-1119-CPR-H2O CPR-Gravity Gun Body 31 60-104 Air Inlet Fitting

14 98-0109 Allen Plug 51-401 Standard 700 mL Gravity Feed Cup (Aluminum)

15 See Air Cap Chart Fan Control Assembly** 51-400 Optional 700 mL Gravity Feed Cup (Plastic)

16 See Air Cap Chart Fluid Needle** 51-403 Optional 1000 mL Gravity Feed Cup (Aluminum)

17 60-1400 Needle Seal* 51-418 Gravity Cup Lid (401 & 403)

18 60-1033 Trigger Pivot Set 51-413 Gravity Cup Lid (400)

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-105

23-1301-G

HVLP AIRCAP TEST GAGES

FOR

H2O-CPR-G

H2O-CPR-G HVLP/PRESSURE REDUCED SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AIR CAP MAXIMUM

PATTERN WIDTH CFM

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

23-2101 11 CFM

23-1301 13.5 CFM

1.3 mm x 2101 or 1301

1.4 mm x 2101 or 1301

1.5 mm x 2101 or 1301

1.7 mm x 2101 or 1301

23-2101 13"

23-1301 12" 23-2101 11 CFM

23-1301 13.5 CFM

1.7 mm x 2101 or 1301

1.9 mm x 1301

2.2 mm x 1301

23-2101 13"

23-1301 12" 23-2101 11 CFM

23-1301 13.5 CFM

FLUID NOZZLE / AIR CAP SELECTION CHARTS

H2O-CPR-G Series - Gravity Feed Guns

0.8 mm x 2101 or 1301

1.0 mm x 2101 or 1301 23-2101 13"

23-1301 12" 23-2101 11 CFM

23-1301 13.5 CFM

1.2 mm x 2101 or 1301

1.3 mm x 2101 or 1301 23-2101 13"

23-1301 12"

Revised1/7/16

H2O-CPR-G-PPSH2O-CPR-G

EP-H2O-CPR-G Includes:

51-401 700 mL Aluminum Gravity Cup

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

EP-H2O-CPR-G-PPS Includes:

91-465 650 mL PPS™ Cup and Collar

91-466 Lids and Liners (Available in 50 Pack)

91-474 #2 PPS Adapter

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

H2O-CPR-G Includes:

51-401 700 mL Aluminum Gravity Cup

52-300 Mini Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

51-430 Gravity Gun Hook

Air Caps and Needles Shown on Page 1

H2O-CPR-G-PPS Includes:

91-465 650 mL PPS™ Cup and Collar

91-466 Lids and Liners (Available in 50 Pack)

91-474 #2 PPS Adapter

52-300 Mini Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

Otros manuales de Pistola pulverizadora de pintura de C.A. Technologies

C.A. Technologies

C.A. Technologies AutoCAT 300C Manual de usuario

C.A. Technologies

C.A. Technologies CPR Manual de usuario

C.A. Technologies

C.A. Technologies FE-Line Fine Finish Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200C Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 300 Series Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200H Manual de usuario

C.A. Technologies

C.A. Technologies CAT-Xpress Guía de solución de problemas

C.A. Technologies

C.A. Technologies Lynx 100C 1590 Manual de usuario

C.A. Technologies

C.A. Technologies CAT SLP Series Manual de usuario

C.A. Technologies

C.A. Technologies AutoCAT 100C Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100CVT Manual de usuario

C.A. Technologies

C.A. Technologies CPR-FE Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 300H Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200Z Manual de usuario

C.A. Technologies

C.A. Technologies LYNX L100CM Manual

C.A. Technologies

C.A. Technologies JAGUAR SLP Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar SLP Manual de usuario

C.A. Technologies

C.A. Technologies Tomahawk TG Manual de usuario

C.A. Technologies

C.A. Technologies TOMCAT 100C Guía de solución de problemas

C.A. Technologies

C.A. Technologies CPR Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 300H Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 200C Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 100 Series Manual de usuario

C.A. Technologies

C.A. Technologies Panther 100G Manual de usuario

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Graco

Graco 246737 Manual de uso y cuidado

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

Graco

Graco EM 390 Manual de operación

DeVilbiss

DeVilbiss LUNA2i Manual de usuario