Brecknell CS-200M Instrucciones de instalación

CS-200M Mechanical Chair Scale

Installation & Operation Instructions

The CS-200M Mechanical Chair Sale is designed for the mobile challenged who have a difficult time

standing on a conventional scale. It is ideal for use in clinics and nursing facilities. The scale is durable,

having a sturdy enameled steel body, a durable molded plastic seat, heavy-duty footrest, and heavy-duty

caster wheels for easy portability.

Figure 1. Mechanical Chair Scale

August 2011 Version 1.0

Installation Instructions

You will receive your Mechanical Chair Scale partially assembled. Those items that need additional

assembly are:

• Pillar and beam assembly to scale base

• Steelyard rod connection

• Transport handle onto scale base

• Seat and footrest installation

• Arm rest installation

Remove all components from the shipping crate and lay out in a convenient place.

Pillar and Beam Installation

The pillar and beam comes separate from the scale base and must be attached prior to use.

Figure 2. Pillar and Beam Components

Use the following steps to attach the pillar and beam to the scale base.

1. Have the scale sitting on the floor in an area that allows you to work freely.

2. Lock casters on the frame to eliminate the unit from rolling while assembling the scale.

Figure 3. Lock Casters to Keep From Rolling

eam

Pillar

Push down on latching assembly

to lock wheels and prevent scale

from rolling.

3. Remove the eight screws from the scale base using a phillips head screwdriver (as shown in the left

hand photo) and set screws aside in a safe place.

Figure 4. Remove Screws From Scale Base and Insert Pillar and Beam into Scale Base Assembly

Insert, but don’t fasten the pillar and beam into the scale base assembly as shown in Figure 4 (right

hand side photo).

Steelyard Rod Connection

The steelyard rod is located inside the pillar. Remove the wire tie(s) holding the steelyard rod

during shipment. Insert the pillar into the base. Once the pillar is inserted to the scale base, the

steelyard rod must be attached to the bottom of the scale. The two photos below show the hook of the

steelyard rod and an inside photo of the ring in the scale bottom. Latch the hook onto the D-shaped ring

shown in the right hand side picture.

Figure 5. Attach The Steelyard Rod To the Scale Base D-Ring

Fasten the eight screws once the pillar and beam is connected to the scale base and the steelyard rod is

hooked.

Figure 6. Insert and Tighten The Eight Screws

Steelyard rod (not

shown)

Steelyard rod

hook

Installing Transport Handle

Once the pillar and beam are attached to the scale support frame and secured, it’s time to attach the

transport handle to the scale support frame (transport handle is illustrated in Figure 8).

1. Remove the four side screws (two on each side as shown in left hand side of Figure 7) from the

scale support frame and set aside. The transport handle will attach to the scale support frame using

those screws.

Figure 7. Transport Handle Installation

2. Insert the transport handle into the two sides of the scale support frame as shown in right side of

Figure 7.

3. Insert and tighten the four screws using a phillips screwdriver as shown in Figure 8.

Figure 8. Insert and Tighten Four Screws for Securing the Transport Handle to the Scale Support Frame

The transport handle should fit snuggly against the scale support frame.

Seat and Footrest Installation

Once the transport handle is attached the next step is to install the molded seat to the scale support

frame.

1. Remove the four screws from the movable scale support frame platform and set aside.

Figure 9. Removable Screws on The Movable Scale Support Frame

2. Set the chair onto the scale support frame platform but do not fasten the screws as the footrest

assembly will also have to be put into place prior to tightening all screws.

3. Remove screws from the chair frame (shown in Figure 10) and set aside.

4. Tilt the chair upwards as shown in Figure 10. This will allow the installer to get the footrest assembly in

place prior to securing the chair to the platform

Figure 10. Tilt the Chair Upward Before Installing the Footrest Assembly

5. Slide the footrest assembly onto the chair scale base as shown in Figure 10.

Note that the footrest assembly for the footrest is hanging on the metal chair channel and lined up

with the screw holes on the channel of the chair scale frame as shown in Figure 11.

Four screws on scale support

Frame – only one screw shown

Figure 11. Slide the Footrest Assembly So That Holes Line Up

Once the footrest is secured and the screws tightened for it, secure the molded seat onto the chair

scale frame.

6. Secure the four screws (shown below).

Figure 12. These Screws Hold The Molded Chair to the Scale Base

Arm Rest Installation

The last item to be installed on the mechanical chair scale are the two arm rests.

Figure 13. Detachable Arm Rest for the Mechanical Chair Scale

Use the following steps to attach the two arm rests to the mechanical chair scale molded seat.

Push footrest assembly back

so that the holes line up.

Secure screws (only

one shown)

1. Locate the bolt hole (x 4) location on the back of the molded chair.

Figure 14. Hole Location and Four Bolts Used for Securing Arm Rest to Chair

2. Secure the arm rests to the molded chair using the four bolts (provided and shown in Figure 14), using

the 5mm allen wrench that’s been provided in this packaging.

Figure 15. Secure Arm Rests to the Molded Chair

3. The arm rests are now in position and can be moved up and down.

Figure 16. Arm Rests Are Secured to the Molded Chair Seat

two bolts for each arm rest

Zero Adjustment

To ensure accurate weighments, a zero adjustment should be done to the scale upon arrival and setup.

To perform a zero adjustment, perform the following steps.

1. Ensure the scale is sitting on a level surface.

2. Check the eye loop area of the scale to ensure that the scale pointer is equally balanced between the

eye loop area.

Figure 17. Eye Loop Area and Zero Adjusting Screw Location

3. If the scale is not balancing properly, then the small zero balance weight must be adjusted. Turn the

zero adjusting screw (shown in Figure 17) using a flat head screwdriver. By adjusting the screw, the

zero balance weight will move accordingly.

4. The scale is now ready to weigh patients.

5. Have the patient sit down on the molded seat. The patient should be completely seated in the

chair, not leaning forward, and having feet firmly positioned on the footrest assembly.

Zero

Adjusting

Screw

Scale

pointer

Eye Loop Area

UK and Europe

Brecknell

Foundry Lane

Smethwick

West Midlands, B66 2LP.

Tel: +44 (0) 845 246 6717

Fax: +44 (0) 845 246 6718

Email: sales@brecknellscales.co.uk

Web site: www. brecknellscales.co.uk

USA

Brecknell

1000 Armstrong Drive

Fairmont MN 56031

Toll Free: 800-637-0529

Tel: 507-238-8702

Fax: 507-238-8271

Email:sales@brecknellscales.com

www. brecknellscales.com

Chaise de pesée mécanique CS-200M

Instructions d’installation et mode d’emploi

________________________________________________________________

La chaise de pesée mécanique CS-200M est destinée aux individus à mobilité réduite qui ont de la

difficulté à se tenir debout sur une balance conventionnelle. Elle est idéale pour une utilisation dans les

cliniques et les établissements de soins. La chaise de pesée est résistante; elle possède un corps en

acier émaillé robuste, un siège en plastique moulé solide, un repose-pieds très résistant et des roues

pivotantes robustes pour faciliter le transport.

Figure 1. Chaise de pesée mécanique

Août 2011 Version 1.0

Instructions d’installation

Votre chaise de pesée mécanique est livrée partiellement assemblée. Les éléments suivants doivent

être montés :

• L’ensemble du pilier et de la traverse de pesée à fixer sur la base de la balance

• La barre de connexion du peson

• La poignée de transport à fixer sur la base de la balance

• Le siège et le repose-pieds

• Les accoudoirs

Retirer tous les éléments de leur emballage et les disposer dans un endroit pratique.

Installation du pilier et de la traverse de pesée

Le pilier et la traverse de pesée sont livrés séparément de la balance et doivent être fixés avant toute

utilisation.

Figure 2. Pilier et traverse de pesée

Suivre les étapes suivantes pour attacher le pilier et la traverse de pesée à la base de la balance.

1. Poser la balance par terre dans une zone vous permettant de travailler librement.

2. Verrouiller les roues pivotantes pour éviter que l’unité roule lors de l’assemblage de la balance.

Figure 3. Verrouiller les roues pivotantes afin que l’unité reste immobile

Traverse de

pesée

Pilier

Appuyer sur le dispositif de

verrouillage pour bloquer les

roues et empêcher ainsi

l'unité de rouler.

Tabla de contenidos

Idiomas:

Otros manuales de Escala de Brecknell

Brecknell

Brecknell LPS Series Manual de usuario

Brecknell

Brecknell 67XXU Series Manual de usuario

Brecknell

Brecknell ELECTROSAMSON Manual de usuario

Brecknell

Brecknell S100 Manual de usuario

Brecknell

Brecknell MS-15 Manual de usuario

Brecknell

Brecknell MS-1000 Manual de usuario

Brecknell

Brecknell MS140/300 Manual de usuario

Brecknell

Brecknell DSB Manual de instrucciones

Brecknell

Brecknell HS-200M Manual de usuario

Brecknell

Brecknell PS25 Manual de usuario

Brecknell

Brecknell 405-6-LCD Manual de usuario

Brecknell

Brecknell BFS-150 Manual de usuario

Brecknell

Brecknell MS16 Manual de usuario

Brecknell

Brecknell PS3000 Manual de usuario

Brecknell

Brecknell PS-7 Manual de operación

Brecknell

Brecknell S133 Manual de usuario

Brecknell

Brecknell 6710U Manual de usuario

Brecknell

Brecknell PS-7 Manual de operación

Brecknell

Brecknell PS 150 Manual de usuario

Brecknell

Brecknell 7010SB Manual de usuario

Brecknell

Brecknell BS-713 Manual de usuario

Brecknell

Brecknell MBS-150 Manual de usuario

Brecknell

Brecknell 405-LCD Manual de usuario

Brecknell

Brecknell MS-20 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario