Bosch AMAX panel 2000 ICP-AMAX-P Manual de usuario

AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500

en User Guide

AMAX panel 2000 / AMAX panel 2000 EN Table of Contents | en 3

Robert Bosch Engineering and Business Solutions Limited User Guide F.01U.249.500 | V2 | 2011.11

Table of Contents

1 Introduction 4

2 Arming and Disarming the System 8

2.1 Arming the System 8

2.1.1 Arming in AWAY mode 8

2.1.2 Arming in STAY mode 9

2.1.3 Forced arming 9

2.2 Disarming the System 9

2.2.1 Disarming with CODE 9

2.2.2 Disarming with wireless control Key 9

2.2.3 Disarming with Key switch 9

3 Faults or Tamper conditions 10

3.1 System fault or tamper analysis Mode 10

4 Walk test mode 12

5 Event Memory Recall mode 13

6 Reset the Control Panel 14

7 Bypassing 15

7.1 Bypassing Zones 15

7.2 Bypassing Faults and Tamper conditions (Except Zone Tampers) 15

8 Enable / Disable the installers code 16

9 Change individual code 17

10 Keypad alarm operation commands 18

10.1 Duress alarm 18

10.2 Keypad panic alarm 18

10.3 Keypad fire alarm 18

10.4 Keypad medical alarm 18

11 Domestic Dialing 19

Glossary 20

Index 21

4en | Introduction AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500 | V2 | 2011.11 User Guide Robert Bosch Engineering and Business Solutions Limited

1 Introduction

Quick keypad operation instructions

Table 1.1 Quick keypad operation instructions

ICP-AMAX - LED8-8 Zone LED Keypad ICP-AMAX-LCD8 - 8 Zone LCD Keypad

Arming

AWAY arm [code] + [#] / [#] (quick arming)

STAY arm [code] + [*] / [*] (quick arming)

Disarming

Disarm [code] + [#]

Other Commands

Fault and

Tamper Analysis

[code] + [2] [#]

Walk test [code] + [4] [#]

Event recall [code] + [5] [#]

System Reset [code] + [6] [#]

Bypassing zones [code] + [9] [#] [zone] + [*] [#]

Bypassing Faults

and Tamper

conditions

[code] + [97] [#]

Enable/Disable

Installer code

Enable = [code] + [98] [#] Disable = [code] + [98] [*]

Change

individual code

[code] + [99] [#] [newcode] [#]

Alarm Commands

Duress alarm [code] + [0] [#]

Emergency

alarm

Simultaneously press and hold [1] and [3] or [*] and [#]

Fire alarm Simultaneously press and hold [4] and [6]

Medical alarm Simultaneously press and hold [7] and [9]

Default user code = 2580

AMAX panel 2000 / AMAX panel 2000 EN Introduction | en 5

Robert Bosch Engineering and Business Solutions Limited User Guide F.01U.249.500 | V2 | 2011.11

Keypad Indicators

Table 1.2 Keypad Indicators

LCD keypad

indicator icons

LED keypad

indicator lights

Status Definition

Zone (1-8) on Zone is triggered.

off Zone is normal.

Fast flash (0.25 seconds lights on/

0.25 seconds lights off)

Zone was alarmed or is in alarm

status.

Slow flash (1 second lights on/1

second lights off)

Zone is manually bypassed or

interior Zone is in STAY ARM mode.

AWAY on System is armed in AWAY mode.

off System not armed in AWAY mode.

Slow flash (1 second lights on/1

second lights off)

Exit time.

Fast flash (0.25 seconds lights on/

0.25 seconds lights off)

Programming mode or Code

function mode. STAY indicator

flashes simultaneously.

STAY on System is armed in STAY mode.

off System not armed in STAY mode.

Slow flash (1 second lights on/1

second lights off)

Exit time.

Fast flash (0.25 seconds lights on/

0.25 seconds lights off)

Programming mode or Code

function mode. AWAY indicator

flashes simultaneously.

When bypass function is

performed, the STAY indicator only

flashes.

MAINS on AC main power is normal.

Slow flash (1 second lights on/1

second lights off)

AC main power supply failed.

FAULTS on System fault or Tamper condition

is present.

off System is in normal status.

Flashes System fault or Tamper condition

must be acknowledged.

on System is disarmed.

1 2 3 ….

6en | Introduction AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500 | V2 | 2011.11 User Guide Robert Bosch Engineering and Business Solutions Limited

Keypad sounds

Table 1.3 Keypad sounds

Sound indicator Definition

One short beep A keypad button has been pressed.

One single one-

second beep

The requested operation is refused. Incorrect operation signal.

Two short beeps The system accepted the code. The system executed the requested

function.

One short beep

per second

In walk test mode.

One short beep

every two

seconds

Exit time started.

Continued

sound

– Last 10s on exit time

– Keypad fault/tamper sound (fault/tamper to be acknowledged)

– Keypad alarm sound

Continuous 0.5

second beep,

stops 0.5

seconds

Entry delay time (until alarm ends or system is disarmed).

AMAX panel 2000 / AMAX panel 2000 EN Introduction | en 7

Robert Bosch Engineering and Business Solutions Limited User Guide F.01U.249.500 | V2 | 2011.11

Zone description

Zone 1 ______________________________________________________

Zone 2 ______________________________________________________

Zone 3 ______________________________________________________

Zone 4 ______________________________________________________

Zone 5 ______________________________________________________

Zone 6 ______________________________________________________

Zone 7 ______________________________________________________

Zone 8 ______________________________________________________

Exit Time ___________________________________________________ sec

Entry Time _________________________________________________ sec

User Code Names

Code 1 _____________________________________________________

Code 2 _____________________________________________________

Code 3 _____________________________________________________

Code 4 _____________________________________________________

Code 5 _____________________________________________________

Code 6 _____________________________________________________

Code 7 _____________________________________________________

Code 8 _____________________________________________________

Code 9 _______________________________________________________Keyfob 1

Code 10 _____________________________________________________ Keyfob 2

Code 11 _____________________________________________________ Keyfob 3

Code 12 _____________________________________________________ Keyfob 4

Code 13 _____________________________________________________ Keyfob 5

Code 14 _____________________________________________________ Keyfob 6

Code 15 _____________________________________________________ Keyfob 7

Code 16 _____________________________________________________ Keyfob 8

8en | Arming and Disarming the System AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500 | V2 | 2011.11 User Guide Robert Bosch Engineering and Business Solutions Limited

2 Arming and Disarming the System

2.1 Arming the System

2.1.1 Arming in AWAY mode

Arming the system in AWAY Mode is normally performed when you leave the premises and

require that all zones are activated in a ready state to detect an intrusion.

2.1.1.1 Keypad arming

The system can be set to AWAY mode in two different ways.

To arm the System in AWAY mode (method 1)

Enter your code and press [#].

Two beeps sound, the AWAY indicator flashes slow, and exit time starts. After exit time, the

AWAY indicator turns is lit.

To arm the System in AWAY mode (method 2)

Press and hold [#] until it beeps twice.

The AWAY indicator flashes slow, and exit time starts. After exit time, the AWAY indicator is lit.

Please contact your installer to enable/disable this function.

2.1.1.2 Telephone remote arming

The user dials the control panel number. The control panel answers the call and issues a long

beep. After the long beep, the user must press the [#] key. When the Panel receives the signal

it will confirm the arming of the control panel with a high tone.

Please contact your installer to enable/disable this function.

2.1.1.3 Arming in AWAY mode with wireless remote control Key

Press and hold the Arming Button until two beeps sound on the remote keypad and the AWAY

indicator flashes slow. Exit time starts. After exit time, the AWAY indicator is lit.

NOTICE!

When the number of incorrect code entries on the keypad reaches a specified number, the

keypad will automatically lock for 180 seconds and alarm is reported.If the keypad is idle for 4

minutes, the system will automatically exit from any operational mode.

RE012E:2 standard wireless remote control key

1 –Button 1: Arm in AWAY mode

2 –Button 2: Disarm

3 –Button 1 and 2: Press both buttons at the same time to activate Panic alarm

1 2

AMAX panel 2000 / AMAX panel 2000 EN Arming and Disarming the System | en 9

Robert Bosch Engineering and Business Solutions Limited User Guide F.01U.249.500 | V2 | 2011.11

2.1.1.4 Key switch arming

Users can use a key switch to Arm and Disarm the system. When the Key switch is activated,

the AWAY indicator flashes slow and exit time starts. After exit time, the AWAY indicator is lit.

When the Key switch is deactivated, the system is disarmed and Away indicator is off.

2.1.2 Arming in STAY mode

STAY Mode is used when you need to arm the perimeter and unused areas of the premises to

detect a would-be intruder, while at the same time being able to move freely within an area

that is automatically isolated

There are two methods to arm your system in STAY Mode

To arm the system in STAY mode (method 1)

Enter your code and press [#].

Two beeps sound, the STAY indicator flashes slow and exit time starts. After exit time, the

STAY indicator is lit.

The lights corresponding to all zones programmed as automatically isolated zones (Interior

Instant Zone) begin to flash and continue until the exit time is finished.

To arm the system in STAY mode (method 2)

Press and hold [#] for 3 seconds.

When two beeps sound, release the button.

The STAY indicator flashes slow and exit time starts. After exit time, the STAY indicator is on.

Please contact your installer to enable/disable this function.

2.1.3 Forced arming

Arming the system when a zone is not sealed is known as forced arming. If the AWAY indicator

does not glow, and if a long beep sounds when you attempt to arm the system in AWAY Mode,

then forced arming is not permitted. If this is the case, then you will have to seal all zones or

manually isolate them before you can arm the system.

Please contact your installer to enable/disable this function.

2.2 Disarming the System

2.2.1 Disarming with CODE

Enter your code and press [#] .Two beeps sound and the AWAY or STAY indicator is

extinguished.

2.2.2 Disarming with wireless control Key

Press and hold the Disarming Button. Two beeps sound and the AWAY or STAY indicator is

extinguished.

2.2.3 Disarming with Key switch

When the Key switch is deactivated, the system is disarmed and the AWAY or STAY indicator is

extinguished.

10 en | Faults or Tamper conditions AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500 | V2 | 2011.11 User Guide Robert Bosch Engineering and Business Solutions Limited

3 Faults or Tamper conditions

Whenever a system fault or tamper condition occurs, the FAULT or MAINS indicator flashes

and the keypad beeps.

3.1 System fault or tamper analysis Mode

To enter fault or tamper analysis mode for determining a system fault or tamper condition:

1. Enter your Code and [2] and press [#]. Two beeps sound.The FAULT indicator remains lit

and the STAY and AWAY indicators flash. The lit zone indicators indicate the type of fault

or tamper condition that occurred.

2. For a multi-level menu, enter the corresponding number to enter the submenu, press [ 0

] key to return to the main menu.

3. To exit from Fault and Tamper Analysis Mode, press [#] . The STAY and AWAY indicators

are extinguished and the FAULT indicator remains lit, and the keypad stops the beep.

NOTICE!

Operation can be carried out only in status.

Otros manuales para AMAX panel 2000 ICP-AMAX-P

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de seguridad de Bosch

Bosch

Bosch DB-CO Manual de usuario

Bosch

Bosch Spexor Manual de usuario

Bosch

Bosch Solution 16i Manual de usuario

Bosch

Bosch LBB 1946 Manual de usuario

Bosch

Bosch Plena LBB1990/00 Guía del usuario

Bosch

Bosch Plena Power Amplifier Manual de usuario

Bosch

Bosch MIC IP starlight 7000i Manual de usuario

Bosch

Bosch D222 Manual de usuario

Bosch

Bosch Solution 16i Manual de usuario

Bosch

Bosch CC880/LP880, SC8016 Manual

Bosch

Bosch ISC-FPB1-W60QS Instrucciones de funcionamiento

Bosch

Bosch Solution 64 Manual de usuario

Bosch

Bosch Radion B810 Manual de usuario

Bosch

Bosch CCS 800 Ultro Manual de usuario

Bosch

Bosch PVA-1EB Manual de usuario

Bosch

Bosch DIP-3042-2HD Manual de usuario

Bosch

Bosch ISC-BDL2-WP12 Manual de usuario

Bosch

Bosch SM120RW Manual de usuario

Bosch

Bosch FMC-210-DM-G-B Manual de usuario

Bosch

Bosch DIP-2040-00N Manual de usuario

Bosch

Bosch PRAESENSA Manual de usuario

Bosch

Bosch AP1-T Manual de usuario

Bosch

Bosch BIS 2.3 Manual de usuario

Bosch

Bosch B Series Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario