Bosch ADS?AMC2?2WCF Manual de usuario

Access Modular Controller 2

ADS‑AMC2‑2WCF | APC‑AMC2‑2WCF

en Installation manual

Access Modular

Controller 2 Table of contents | en 3

Bosch Security Systems B.V. 2019-11 | V02 |

Table of contents

1Safety 4

1.1 Unpacking 5

2Short information 6

3Introduction 8

3.1 Description 8

3.2 Product overview 10

3.3 System overview 15

4Installing 16

4.1 Mounting the device on a mounting rail 16

4.2 Unmounting the device from a mounting rail 17

4.3 Opening the case 18

4.4 Closing the case 19

4.5 Cabling 20

4.5.1 Conductor data for powering the controller 20

4.6 Grounding and shielding 22

4.6.1 Grounding for Host Interface 22

4.6.2 Grounding for Extension Interface 23

4.7 Connecting the power supply to the controller 25

4.8 Ethernet Host Interface 26

4.9 RS-485 Host Interface 27

5Operating 29

5.1 Configuring Ethernet interface 29

6Troubleshooting 30

6.1 Resetting the software 32

6.2 Resetting the device to factory default 32

7Service and repair 34

8Disposal 35

9Technical specifications 36

10 Appendices 39

10.1 Connecting diagrams 39

4en | Safety Access Modular

Controller 2

2019-11 | V02 | Bosch Security Systems B.V.

1 Safety

Read instructions

Read all technical documentation before installing or using the

device. Make sure that you have understood all information

described in the technical documentation. Do not ignore safety

messages, as this can cause property or personal damage.

Retain instructions for future reference.

Warning!

Risk of physical injury due to blocked escape routes

The access modular controller may block escape routes if not

installed correctly. To keep escape routes free:

- Use locks in fail-safe mode, so that doors will be released if

power fails.

- Install manual override switches, such as break-glass or lever

stations, to unlock doors in an emergency.

Warning!

Risk of explosion of lithium battery

The battery can explode if replaced incorrectly.

Replace battery with the same type as recommended by Bosch.

Dispose used batteries according to the instructions of the

manufacturer of the batteries.

Caution!

Fire hazard and risk of electric shock due to unauthorized

spare parts and accessories

Unauthorized spare parts and accessories might lack grounding

wires or other safety elements. External power supplies must

be installed and put into service by qualified personnel. The

service technician must use replacement parts or accessories

that are specified by the manufacturer.

Access Modular

Controller 2 Safety | en 5

Bosch Security Systems B.V. 2019-11 | V02 |

Notice!

Device damage due to electrostatic discharge

Protect the hardware from electrostatic discharge, especially

when the device is opened. Always disconnect the controller

from the power source before modifying the installation. The

controller does not support hot-plugging.

Notice!

Unauthorized access

If the access modular controller is installed in an unprotected

environment, unauthorized people may be able to enter.

Install the controller in a location with restricted access.

Notice!

Device damage due to incorrect mounting

The controller can fall and break. Mount the controller on the

matching mounting rails.

This product is RoHS compliant. See Technical data for the full

table of hazardous components.

1.1 Unpacking

Check the packaging for visible damage. If anything has been

damaged during transport, please inform the transport agency.

Unpack the unit carefully. This is an electronic device that must

be handled with care to avoid damage. Do not attempt to put

the unit into operation if components are damaged.

If any parts are missing, inform your customer service

representative or a Bosch Security Systems salesperson. The

shipping carton is the safest transport container for the unit.

Store it and the other packaging material for future use. If the

unit has to be sent back, use the original packaging.

6en | Short information Access Modular

Controller 2

2019-11 | V02 | Bosch Security Systems B.V.

2 Short information

This controller is able to control up to two Wiegand card

readers.

It is designed to fully process the access logic at assigned

access points. Access points consist of doors, gates, barriers,

turn stiles, revolving doors, mantraps, ID card readers, door

opening elements and sensors.

All the product versions use encrypted connections between the

access modular controller and the host system.

The controller stores all necessary information in a battery-

buffered memory and in a compact flash storage element. Even

when the unit is offline, it is able to perform:

– Independent status and authorization checks on access

points

– Take access decisions

– Activate and deactivate connected peripheral elements

– Detect and register all relevant events

The Access Modular Controller (AMC) is supported by the

Access Professional Edition (APE), BIS Access Engine (ACE) and

the Access Management System (AMS).

For more information about our products, visit our online

product catalog.

Manufacturing dates

For product manufacturing dates, go to http://

www.boschsecurity.com/datecodes/ and refer to the serial

number on the product label.

Remarks

This hardware is part of a security system.

Access Modular

Controller 2 Short information | en 7

Bosch Security Systems B.V. 2019-11 | V02 |

Access should be limited to authorized people only.

Some states do not allow the exclusion or limitation of implied

warranties, or limitation of liability for incidental or

consequential damages, hence the above limitation or exclusion

might not apply to you.

Bosch Security Systems retains all rights not expressly granted.

Nothing in this license constitutes a waiver of Bosch’s rights

under the U.S. Copyright laws or any other federal or state law.

If you need further assistance or have any questions, contact:

Bosch Security Systems B.V.

Torenallee 49

5617 BA Eindhoven

Netherlands

www.boschsecurity.com

8en | Introduction Access Modular

Controller 2

2019-11 | V02 | Bosch Security Systems B.V.

3 Introduction

3.1 Description

The controller is equipped with two independent interfaces for

Wiegand type readers. It is able to control one door with one

reader in each direction and up to two doors with a reader in

one direction only.

Figure3.1: Access Modular Controller

All necessary information for access verification is stored in a

battery buffered on-board memory and a Compact Flash (CF)

memory card. This guarantees autonomous access decisions and

complete access registrations even if the management host

system is offline. The built in compact flash card provides

adequate storage capability for cardholders and events.

Access Modular

Controller 2 Introduction | en 9

Bosch Security Systems B.V. 2019-11 | V02 |

The electronics of the controller are completely covered by a

plastic housing. The LCD (liquid crystal display) provides all

important status information.

Unsecured Area

The controller can communicate upstream to the host computer

using RS-485 multi-dropped. It has four analog input devices

and four relay outputs. With its analog input devices, the

controller verifies, for example, if a lock is closed or open. The

relay outputs can be used to activate lock mechanisms if access

is granted, or activate the burglar alarm system if an intrusion or

system alert is detected. If the four inputs and four outputs on

board are not enough to configure the system, up to three

additional extension boards can be connected. The extensions

offer 8 or 16 additional inputs and outputs.

The setup procedure for a controller is made very simple and

fast by the use of door templates. Once selected, all the inputs

and outputs are predefined. These settings can be changed to

choose every free contact of the controller or a connected

extension.

10 en | Introduction Access Modular

Controller 2

2019-11 | V02 | Bosch Security Systems B.V.

3.2 Product overview

Mainboard

Figure3.2: Upper circuit board with display (front)

1 DIL switch for RS-485 address selection , protocol, and

RS-232/RS-485 selection.

2 Lithium battery for buffering of static RAM and real time

clock (RTC). The battery life is estimated at 10 years,

nevertheless an error message is generated if the voltage

sinks below a preset minimum level.

NOTICE: In order to avoid an error message caused by an

earlier voltage drop we suggest to replace the battery

every 8 years. Spare part: VARTA CR 2032 PCB.

3 Reset push button - reachable through the casing using a

screwdriver

4 Liquid Crystal Display

5 Push button, available on top of the housing, to select

different display modes

6 Jumper: Equalization of potential between different

systems and earth ground (shield)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Bosch

Bosch

Bosch rexroth HMS01 Manual de usuario

Bosch

Bosch Access Modular Controller 2 Manual de usuario

Bosch

Bosch Rexroth IndraControl L25 Manual de usuario

Bosch

Bosch Heatronic 4000 Manual

Bosch

Bosch Rexroth SYHNC100-SEK 3 Series Manual de usuario

Bosch

Bosch MP 100 Manual de usuario

Bosch

Bosch CR 10 Manual de usuario

Bosch

Bosch Rexroth GTM Series Manual técnico

Bosch

Bosch EasyControl CT200 Manual de usuario

Bosch

Bosch PVA-4CR12 Manual de usuario

Bosch

Bosch EasyControl CT200B Manual de usuario

Bosch

Bosch rexroth CHC Manual de usuario

Bosch

Bosch Smart Home Controller AA Manual de usuario

Bosch

Bosch WORCESTER GREENSTAR WIRING CENTRE Guía del usuario

Bosch

Bosch AMC2-16IOE Manual de usuario

Bosch

Bosch FW 200 Manual de instrucciones

Bosch

Bosch Rexroth lndraDrive HCS02.1E-W0012 03 Series Manual de usuario

Bosch

Bosch Rexroth CS660 Manual de usuario

Bosch

Bosch Rexroth OptiFeed-FS EcoDrive 03 FLP04VRS Instrucciones de funcionamiento e instalación

Bosch

Bosch CS 550 Manual de usuario

Bosch

Bosch Rexroth ctrl CORE Manual de usuario

Bosch

Bosch Rexroth Rho 4.0 Manual de usuario

Bosch

Bosch CL550 Manual de usuario

Bosch

Bosch REXROTH IndraMotion MLD Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario