Bosch AMC2 Series Manual de usuario
AMC2 Modular Controller
AMC2‑4W_UL
en Installation Manual
AMC2 Modular
Controller Table of contents | en 3
Bosch Access Systems GmbH 2018-09 | AMC2-4W_UL |
Table of contents
1Safety Instructions 5
1.1 Important Safety Notes 5
1.2 FCC & ICES Information 8
1.3 Safety Precautions 9
1.4 Unpacking 11
2Important Information 12
2.1 Explanation of symbols in this document 12
2.2 Internet 13
3Introduction 14
3.1 Description 14
3.2 Equipment Configuration 16
3.3 Performance Characteristics 20
3.4 System Overview 21
4Installing 23
4.1 Mounting 23
4.2 Unmounting 24
4.3 Opening the Case 25
4.4 Closing the Case 26
4.5 Cabling 27
4.5.1 Conductor data for power to AMC2 27
4.6 Grounding and Shielding 29
4.6.1 Grounding for Extension Interface 30
4.7 Connecting Power Supply 31
4.8 Ethernet Host Interface 32
4.9 RS-485 for extension modules 34
4.10 Wiegand Interface for Card Readers 36
4.11 Connecting Relay Outputs 37
4.12 Connecting Analog Input Devices 41
4.13 Tamper Protection 44
5UL Requirements 45
5.1 System Requirements 46
5.1.1 Computer 46
5.1.2 Monitor 47
5.1.3 Printer 47
4en | Table of contents AMC2 Modular
Controller
2018-09 | AMC2-4W_UL | Bosch Access Systems GmbH
5.2 UL 294 Level Descriptions 47
5.3 Installation Instructions 48
6Operating 52
6.1 Status Display of the AMC2 52
6.2 Configuring the Ethernet Interface 55
6.3 Troubleshooting 56
6.3.1 Resetting the Software 56
6.3.2 Resetting the Device to Factory Default 58
7Technical Data 59
8Appendices 63
8.1 Connecting Diagrams 63
Index 67
AMC2 Modular
Controller Safety Instructions | en 5
Bosch Access Systems GmbH 2018-09 | AMC2-4W_UL |
1 Safety Instructions
1.1 Important Safety Notes
1. Read, follow, and retain instructions - All safety and
operating instructions must be read and followed properly
before putting the unit into operation. Retain instructions
for future reference.
2. Do not ignore warnings - Adhere to all warnings on the unit
and in the operating instructions.
3. Accessories - Use only accessories recommended by the
manufacturer or those sold with the product. Accessories
not recommended by the manufacturer must not be used,
as they may cause hazards.
4. Installation precautions - Do not place this unit on an
unstable stand, tripod, bracket, or mount. The unit may fall,
causing serious injury to persons and damage to the unit.
Mount the unit according to the manufacturer’s
instructions.
5. Service - Do not attempt to service this unit by yourself.
Opening or removing covers may expose you to dangerous
voltages or other hazards. Refer all servicing to qualified
service personnel.
6. Damage which requires service - Disconnect the unit from
the main AC or DC power source and refer servicing to
qualified service personnel under the following conditions:
– If the power supply cord or plug is damaged.
– If liquid has been spilled or an object has fallen into
the unit.
– If the unit has been exposed to water and/or inclement
weather (rain, snow, etc.).
– If the unit does not operate normally when following
the operating instructions. Adjust only those controls
specified in the operating instructions. Improper
6en | Safety Instructions AMC2 Modular
Controller
2018-09 | AMC2-4W_UL | Bosch Access Systems GmbH
adjustment of other controls may result in damage,
and require extensive work by a qualified technician to
restore the unit to normal operation.
– If the unit has been dropped or the cabinet damaged.
– If the unit exhibits a distinct change in performance.
7. Replacement parts - If replacement parts are required, the
service technician must use only replacement parts that are
specified by the manufacturer. Unauthorized replacements
may result in fire, electrical shock or other hazards.
8. Safety check - Upon completion of service or repair work
on the unit, ask the service technician to perform safety
checks to ensure that the unit operates properly
9. Power sources - Operate the unit only from the type of
power source indicated on the label. If unsure of the type
of power supply to use, contact your dealer
– For units intended to operate on battery power, refer
to the operating instructions.
– For units intended to operate with external power
supplies, use only the recommended approved power
supplies corresponding to norm EN/UL 60950.
– For units intended to operate with a limited power
source, this power source must comply with EN/UL
60950. Unsuitable replacements may damage the unit
or cause fire or shock.
– For units intended to operate at 12V DC normal input
voltage is 12V DC. Voltage input must never exceed
15V DC.
– For UL installations, the Bosch APS-PSU-60 power
supply may be used, and must be located in the same
room as the connected AMC2 device. Recommended
maximum distance between power supply unit and
AMC2 is 3 m (9.84 ft).
10. Lightning - For added protection during electrical storms
external lightning conductors can be installed. This
prevents power surges from damaging the unit.
AMC2 Modular
Controller Safety Instructions | en 7
Bosch Access Systems GmbH 2018-09 | AMC2-4W_UL |
– For UL installations, lightning protection used must be
UL listed.
11. The units should be installed in locations with restricted
access.
8en | Safety Instructions AMC2 Modular
Controller
2018-09 | AMC2-4W_UL | Bosch Access Systems GmbH
1.2 FCC & ICES Information
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must tolerate
any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
rules. The limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Reorient or relocate receiving antenna
2. Increase the separation between the equipment and the
receiver
3. Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
4. Consult the dealer or an experienced radio/TV technician
for help
AMC2 Modular
Controller Safety Instructions | en 9
Bosch Access Systems GmbH 2018-09 | AMC2-4W_UL |
1.3 Safety Precautions
Read instructions!
Before working with the AMC2 device, read these instructions
carefully. Make sure you have understood all information
described in this document.
!
Warning!
Risk of electric shock
External power supplies must be installed and put into service
by qualified personnel.
Ensure compliance with the relevant regulations.
Ground the controller.
Disconnect both AC and battery power supply before working
on the controller.
!
Warning!
Risk of fire
Installation of the AMC2 device must comply with any local fire,
health, and safety regulations. A secured door that may be part
of an escape route from an area must be installed with:
Install a fail-safe lock (A), so that the door will be released if
power fails. Ideally, use a magnetic lock.
Install a normally-closed break glass or a manual pull (B) in the
lock supply wiring, so that in an emergency the fail-safe lock
can be immediately powered down.
!
Warning!
Risk of explosion of Lithium battery
The battery can explode if it is replaced incorrectly.
Replace only with the same type as recommended by the
manufacturer.
Dispose used batteries according to the battery manufacturer’s
instructions.
10 en | Safety Instructions AMC2 Modular
Controller
2018-09 | AMC2-4W_UL | Bosch Access Systems GmbH
Notice!
Risk of damage to equipment
Protect the hardware from electrostatic discharge by observing
ESD instructions before unpacking of touching connectors of
electronics.
Always switch off power of the AMC2 device before modifying
the installation.
Do not connect or disconnect plug connectors, data cables, or
screw connectors while power is on.
Rules and Conditions
There are no specific requirements as for selling and delivery. As
for storage and safe operation, the environmental temperature
should not exceed the range of 0°C to 50°C.
Disposal
Your Bosch product is designed and manufactured with high-
quality materials and components which can be recycled and
reused.
This symbol means that electrical and electronic equipment, at
their end-of-life, should be disposed of separately from your
household waste.
In the European Union, there are separate collection systems for
used electrical and electronic products. Please dispose of this
equipment at your local community waste collection/recycling
center.
Otros manuales para AMC2 Series
6
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Controladores de Bosch
Bosch
Bosch Rexroth IndraControl L25 Manual de usuario
Bosch
Bosch Rexroth lndraDrive HCS02 Series Manual de usuario
Bosch
Bosch BMS-BAC Manual de usuario
Bosch
Bosch Rexroth 31 Series Manual de instrucciones
Bosch
Bosch rexroth ctrlX CORE Manual de usuario
Bosch
Bosch HPC Manual de usuario
Bosch
Bosch 2600 Series Manual de usuario
Bosch
Bosch B443 Manual de usuario
Bosch
Bosch APC-AMC2-4R4CF Manual de usuario
Bosch
Bosch REXROTH IndraDrive Manual de usuario
Bosch
Bosch Rexroth Diax 04 Manual de usuario
Bosch
Bosch EasyControl CT200 Manual de usuario
Bosch
Bosch Rexroth ACU Series Guía
Bosch
Bosch MP 100 Manual de usuario
Bosch
Bosch CR 10H Manual de usuario
Bosch
Bosch System Controller Manual de usuario
Bosch
Bosch Rexroth IndraControl VPB 40.3 Manual de usuario
Bosch
Bosch MPC-C Series Manual de usuario
Bosch
Bosch Worcester TDS 10 Manual de usuario
Bosch
Bosch ADS?AMC2?2WCF Manual de usuario
