Bosch READYKEY PRO LNL-500 Manual de usuario
LNL-500 Intelligent System Controller
Quick Reference Guide
For detailed information, please refer to the LNL-500 tab in the READYKEYPRO Hardware Installation
Guide (49289).
1.0 The ISC Board
The ISC board contains the following
components (Refer to Figure 1):
A. two (2) unsupervised alarm inputs
B. one (1) RS-232 or RS-485 interface
C. two (2) downstream RS-485 interfaces
(which can consist of one 4-wire and
two 2-wire interfaces)
D. a set of three (3) status LEDs
E. one (1) bank of eight (8) dip switches
F. eleven (11) jumpers
G. one (1) power-in input
H. and one (1) memory backup
(3 volt lithium) battery
I. one (1) TCP/IP Connector
Figure 1: LNL-500
1.1 Unsupervised Alarm Input Wiring
GND
CABINET
TAMPER
POWER
FAULT GND
IN2
IN1
Figure 2: Unsupervised Alarm Input Wiring
If either of these inputs is not used, a jumper
wire should be installed.
If RS-485 communication is used, an RS-232
to RS-485 converter is required at the host
workstation.
LNL-500
LNL-500 Quick Reference Guide
49305D Page 2 © 2006 Bosch Security Systems, Inc.
1.2 Wiring Configuration
Port 1 ISC 9-pin 25-pin
TXD/TR1+ pin 2 pin 3
RXD/TR1- pin 3 pin 2
RTS/R1+ not used not used
CTR/R1- pin 7 pin 4
GND pin 5 pin 7
Jumper together 4, 6 & 8 5, 6 & 20
This configuration will work for Direct Connect
(RS-232) and Lantronix Ethernet network
communications. With direct connect, or Dial-up
DIP switch 5 needs to be OFF, and with Lantronix,
DIP switch 5 needs to be ON.
Table 1: LNL-500 Pinout Connections
PORT 1, CONFIGURED AS
RS-232
TR1+
TR1-
GND
R1 -
R1 +
4-WIRE
TR- TR+ R- R+ SG
PORT 1, CONFIGURED AS RS-485
TXD/TR1+
RXD/TR1-
GND
CTS/R1 -
RTS/R1 +
TXD/TR1+
RXD/TR1-
GND
CTS/R1 -
RTS/R1 +
2-WIRE
TO RS232/RS485
CONVERTER TO RS232/RS485
CONVERTER
To PC
RS-485
2-Wire
Configuration
RS-485
4-Wire
Configuration
RS-232
Direct
Connection
Figure 3: Upstream Host Communication Wiring (Port 1)
If Using A 12 VDC Power Source, Be Sure To Observe
Polarity. VIN
GND
12 to 24 VDC
+
-
Figure 4: Power Source Wiring
Port 2 and Port 3
To configure all four downstream ISC ports as 2-wire RS-485, follow the 2-wire diagram and repeat on each set
of three terminators, TR2+, TR2-, GND and TR3+, TR3-, GND
Port 2/3
TR2+, TR2-
TR3+, TR3- GND
To configure as a 4-wire RS-485 ports, follow the
4-wire diagram (Table 2).
Must terminate the RS-485 at each end-of-
line device.
Table 2: Ports 2-3, RS-485
LNL-500
LNL-500 Quick Reference Guide
© 2006 Bosch Security Systems, Inc. Page 3 49305D
2.0 DIP Switches DIP
Switch(es) USED TO CONFIGURE:
1, 2, 3, 4 Processor address (0 – 7)
5 Communication handshake status (“CTS
enabled” or “none”)
6, 7 Communication baud rate (38400, 19200,
9600 bps)
8 Not Used
The ISC board contains 8 DIP switches that must
be configured appropriately for your system.
Figure 5 shows the default address of 0, CTS
enabled, and baud rate set to 38,400 bps.
1
ON
234567 8
Figure 5: DIP Switch Settings
Table 3: DIP Switch Settings
2.1 Processor Address
DIP Switch
Address 1 2 3 4
Default 0 OFF OFF OFF OFF
1 ON OFF OFF OFF
2 OFF ON OFF OFF
3 ON ON OFF OFF
4 OFF OFF ON OFF
5 ON OFF ON OFF
6 OFF ON ON OFF
7 ON ON ON OFF
Table 4: Processor Address
2.2 Communication Handshake
Status
HANDSHAKE
STATUS: DIP
SWITCH 5
Transmit enabled by
CTS ON Default
None off
Table 5: Handshake Status
2.3 Communication Baud Rate
(upstream and downstream)
DIP SWITCH
BAUD RATE: 6 7
38,400 bps ON ON Default
19,200 bps off ON
9600 bps ON off
off off
Table 6: Communication Baud Rate
Note: The READYKEYPRO Intelligent System
Controller does not currently support this
feature. Therefore, set DIP switch 8 to the “off”
(“Not used”) position, according to the following
table.
PASSWORD STATUS: DIP
SWITCH 8
NOT USED off Default
Table 7: Password Status
© 2006 Bosch Security Systems, Inc.
130 Perinton Parkway, Fairport, NY 14450-9199 USA
Customer Service: (800) 289-0096; Technical Support: (888) 886-6189
49305D
Quick Reference Guide 10/06
LNL-500
Page 4 of 4
3.0 Installing Jumpers Jumper(s) Used to configure:
J3,J4,J5,J6,
J9 Port 1 communication interface type
(RS-485, RS-232)
J7 Port 1 RS-485 type (2-wire, 4-wire)
J8, J10 Port 1 EOL termination status (On, Not On)
J11 Port 2 EOL termination status (On, Not On)
J12 Port 3 EOL termination status (On, Not On)
J13 Port 1 Serial (RS-232), Ethernet
The ISC board contains 11 jumpers that must be
configured appropriately for your system. Table 8
describes the use of each jumper on the ISC
board.
Table 8: Jumper Configuration
J7
2W
4W
2-Wire Configuration for
Jumper J7
J7
2W
4W
4-Wire Configuration for
Jumper J7
Figure 6: Port 1 – RS-485 Type
J3
J5
J6
J9
J4
RS-232 Configuration for
Jumpers J3, J4, J5, J6, J7,
J9
J3
J5
J6
J9
J4
RS-485 Configuration for
Jumpers J3, J4, J5, J6, J7,
J9
J8
J11
EOL Terminator “On”
Configuration for Jumpers
J8, J10
J8
J11
EOL Terminator “Not On”
Configuration for Jumpers
J8, J10
Figure 7: Communication Interface Type Figure 8: Port 1 – RS-485 EOL Terminator Status
J11
EOL Terminator “On”
Configuration for
Jumper J11
J11
EOL Terminator “Not On”
Configuration for
Jumper J11
J12
EOL Terminator “On”
Configuration for
Jumper J12
J12
EOL Terminator “Not On”
Configuration for
Jumper J12
Figure 9: Port 2 – RS-485 EOL Terminator Status Figure 10: Port 3 – RS-485 EOL Terminator Status
J13
Serial or Dial-up
Configuration for
Jumper J13
J13
Ethernet Configuration for
Jumper J13
Figure 11: Port 1 – RS232, Serial, Ethernet Type
Otros manuales de Controladores de Bosch
Bosch
Bosch D2212B Guía de inicio rápido
Bosch
Bosch REXROTH SB356 Manual de usuario
Bosch
Bosch Rexroth CKL Series Guía
Bosch
Bosch EasyControl CT200 Manual de usuario
Bosch
Bosch ARC R-1 Instrucciones de funcionamiento
Bosch
Bosch LTC 8600 Manual de usuario
Bosch
Bosch EasyControl CT200 Manual de usuario
Bosch
Bosch CR 10H Manual de usuario
Bosch
Bosch AMC-4W Manual de usuario
Bosch
Bosch AMC2-16IOE Manual de usuario
Bosch
Bosch Rexroth 31 Series Manual de instrucciones
Bosch
Bosch AMC2-4W Manual de usuario
Bosch
Bosch Rexroth VT-HNC100 3X/S Series Manual de usuario
Bosch
Bosch Rexroth lndraDrive HCS02 Series Manual de usuario
Bosch
Bosch rexroth ctrlX CORE Manual de usuario
Bosch
Bosch Worcester Digital Twin Channel Programmer Manual
Bosch
Bosch CR 10 Manual de usuario
Bosch
Bosch rexroth HMS01 Manual de usuario
Bosch
Bosch Heatronic 4000 Manual
Bosch
Bosch AMC2 Series Manual de usuario
