Belden Hirschmann RS20 Series Manual de usuario

Installation RS20/22/30/32/40

Release

06/2013

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial ETHERNET Rail Switch

RS20/RS22/RS30/RS32/RS40 Family

RS30-0802...

RS30

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS30-1602...

RS20

+24V(P1) 0V 0V

FAULT

+24V(P2)

LS DA

RS30

+24V(P1) 0V 0V

FAULT

+24V(P2)

LS DA

RS20

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

LS DA

V.24

USB

Stand by

FAULT

RS20

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

LS DA

V.24

USB

Stand by

FAULT

RS20

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS20-0800...RS20-2400... RS20-0400...

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS20-0900...

RS40

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS40-0009... RS32-0802... RPS90/48V HV

RPS90/48V HV

U: 110 / 230 VAC

U: 60 / 250 VDC

-/N

+/L

+48V / 1,9A

48-54V

RS32

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

FAULT

+48V(P1) 0V 0V +48V(P2)

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

RS20/22/30/32/40 039 692-003-03-0613 –05.06.2013

Installation RS20/22/30/32/40

Release

06/2013 3

Contents

Safety instructions 4

About this Manual 14

Key 14

1 Description 15

1.1 Description of the device variants 16

1.1.1 Combination options for RS20/30 17

1.1.2 Combination options for RS40 20

1.1.3 Number of ports and media for RS20-... 21

1.1.4 Number of ports and media for RS30-... 25

1.1.5 Number of ports and media for RS40-... 28

1.2 Device variants with PoE (optional) 29

1.2.1 Number of ports and media for devices with PoE 29

1.2.2 PoE power units 31

2 Assembly and start-up 32

2.1 Installing the device 32

2.1.1 Unpacking and checking 32

2.1.2 Installing the SFP transceivers (optional) 33

2.1.3 Insert data in label area 33

2.1.4 Adjust DIP switch settings 34

2.1.5 RS20/RS30/RS40: supply voltage and signal contact 34

2.1.6 RS22/RS32: supply voltage and signal contact 36

2.1.7 Installing the device on the DIN rail, grounding 40

2.1.8 Dimension drawings 43

2.1.9 Connecting the ferrite 46

2.1.10 Installing the terminal block, start-up procedure 47

2.1.11 Connecting the data lines 47

2.2 Display elements 50

2.3 Basic set-up 52

2.4 Maintenance 54

2.5 Disassembly 55

3 Technical data 56

A Further Support 65

4Installation RS20/22/30/32/40

Release

06/2013

Safety instructions

Certified usage

Please observe the following: The device may only be employed for the

purposes described in the catalog and technical description, and only in

conjunction with external devices and components recommended or

approved by the manufacturer. The product can only be operated

correctly and safely if it is transported, stored, installed and assembled

properly and correctly. Furthermore, it must be operated and serviced

carefully.

Supply voltage

For safety reasons the devices have been designed to operate at low

voltages. Thus, they may only be connected to the supply voltage

connections and to the signal contact with SELV circuits with the voltage

restrictions in accordance with IEC/EN 60950-1.

The supply voltage is electrically isolated from the housing.

Use undamaged parts.

Relevant for North America:

The device may only be connected to a Class 2 supply voltage that

fulfills the requirements of the National Electrical Code, Table 11(b). If

the voltage is being supplied redundantly (two different voltage

sources), the combined supply voltages must fulfill the requirements of

the National Electrical Code, Table 11(b).

Relevant for North America: For use in class 2 circuits.

Use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire only.

Relevant for North America

for devices certified for hazardous locations:

Power, input and output (I/O) wiring must be in accordance with

Class I, Division 2 wiring methods [Article 501-4(b) of the National

Electrical Code, NFPA 70] and in accordance with the authority having

jurisdiction.

The device does not contain any service components. Internal fuses

are only triggered if there is a fault in the device. If the device is not

functioning correctly, or if it is damaged, switch off the voltage supply

and return the device to the plant for inspection.

Only switch on the supply voltage for the device when the following

prerequisites are fulfilled:

The housing is closed

The terminal blocks are wired correctly

The terminal blocks for the voltage supply are connected

Installation RS20/22/30/32/40

Release

06/2013 5

Supply voltage for PoE power supply units (optional)

Connect the protective conductor with the ground screw before you

set up the other connections. When removing the connections, you

remove the protective conductor last.

Make sure that the cross-section of the protective conductor cable is

the same size as or bigger than the cross-section of the voltage supply

cables.

Only use connection cables that are permitted for the specified

temperature range.

Shielding ground

Note: The shield ground wire of the twisted pair lines is connected to the

front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

WARNING

ELECTRIC SHOCK

Only connect a supply voltage as described in the data plate of your device.

PoE power supply unit RPS90/48V LV:18 V DC to 60 V DC

PoE power supply unit RPS90/48V HV:48 V DC to 320 V DC or 90 V AC

to 265 V AC

- If the neutral conductor or the negative terminal of the supply voltage is not

grounded

- If you are using a DC voltage greater than 125 V DC for the supply voltage

install a suitable input fuse.

For RPS90/48V-LV power supply units, use a slow-blow fuse with a nominal

rating of 10 A for the voltage supply input.

For RPS90/48V-HV power supply units, use a slow-blow fuse with a

nominal rating of 6.3 A.

With AC power supply, use a cable cross-section of at least 0.75 mm² (for

North America AWG 18) for the current conductor at the voltage input.

With DC power supply, use a cable cross-section of at least 1.0 mm² (for

North America AWG 16) for the current conductor at the voltage input.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation RS20/22/30/32/40

Release

06/2013

Hazardous Locations

Relevant for North America for devices certified for Hazardous Locations:

Power, input and output (I/O) wiring must be in accordance with Class I,

Division 2 wiring methods [Article 501-4(b) of the National Electrical

Code, NFPA 70] and in accordance with the authority having jurisdiction.

SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D

HAZARDOUS LOCATIONS, OR NON-HAZARDOUS LOCATIONS

ONLY.

WARNING – EXPLOSION HAZARD – SUBSTITUTION OF ANY

COMPONENTS MAY IMPAIR SUITABLE FOR CLASS I, DIVISION 2.

WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT

EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS

KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.

The USB connector is for temporary connection only. Do not use,

connect, or disconnect unless area is known to be non-hazardous.

Connection or disconnection in an explosive atmosphere could result in

an explosion.

Peripheral equipment must be suitabel for the location it is used in.

Use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire only.

Installation RS20/22/30/32/40

Release

06/2013 7

CONTROL DRAWING: Hazardous Locations Class I, Division 2, Groups A, B ,C ,D

Notes:

The nonincendive field wiring circuit concept allows interconnection of nonincendive field wiring apparatus

and associated nonincendive field wiring apparatus using any of the wiring methods permitted for

unclassified locations when certain parametric conditions are met.

CaCi+ CCable ; LaLi+ LCable

Nonincendive field wiring circuits must be wired in accordance with the National Electrical Code (NEC),

NFPA 70 , article 501.

Nonincendive Field Wiring Parameters:

Entity Parameters

... for Class I, Division 2, Groups A,B,C,D =>

Vmax

[V]

Imax

[mA]

[nF]

[µH]

Fault contacts 30 90 2.5 1.0

WARNING - EXPLOSION HAZARD – SUBSTITUTION OF ANY COMPONENTS MAY IMPAIR

SUITABILITY FOR HAZARDOUS LOCATIONS OR EXPLOSIVE ATMOSPHERES.

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN

SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.

DO NOT OPEN WHEN ENERGIZED.

CONTROL DRAWING for RS20, RS22, RS30, RS32 and RS40 Family

Size A4 Document No.: 000157671DNR Rev. 0

Date: 2011-09-21 Sheet 1 of 1

NON HAZARDOUS LOCATION

USB Port for Auto Configuration

Adapter.

For maintenance only

See

HAZARDOUS LOCATION

Fault contacts. Equipment with nonincendive

field wiring parameters:

V<30V I<90mA L

<1,0µH C

<2.5nF

USB Port for Auto Configuration Adapter.

For maintenance only – See Installation

Instructions

USB Port for Auto Configuration Adapter.

For maintenance only – See Installation

Instructions

Power supply (Redundant: P1 P2)

Type “P”: 48Vdc

(47Vdc min. … 52Vdc max.)

Fault contacts. Equipment with nonincendive

field wiring parameters:

V<30V I<90mA Li<1,0µH Ci<2.5nF

Power supply:

(Redundant: P1 P2)

Type “D”: 9.6Vdc – 60Vdc

8Installation RS20/22/30/32/40

Release

06/2013

ATEX directive 94/9/EG – specific regulations for safe

operation

Relevant for RS20/22/30/32/40 devices when operating in explosive gas

atmospheres according to ATEX Directive 94/9/EC, the following applies:

List of Standards:

EN 60079-0:2009

EN60079-15:2010

Certificate No.: DEKRA 11ATEX0139 X or KEMA 09ATEX0067 X.

Make sure that the device has the following label:

II 3G Ex nA IIC T4 Gc DEKRA 11ATEX0139 X

for RS20/22/30/32 types.

II 3G Ex nA IIC T3 ... T4 Gc KEMA 09ATEX0067 X

for RS40 types.

Ambient rating and temperature code for RS20 and RS30 types:

T4: 0 °C ≤Ta ≤+60 °C for „S“ types (item 14 of nomenclature

breakdown) or

T4: −40 °C ≤Ta ≤+70 °C for „T“ or „E“ types (item 14 of

nomenclature breakdown).

Ambient rating and temperature code for RS22 and RS32 types:

T4: −40 °C ≤Ta ≤+50 °C for „T“ or „E“ types (item 14 of

nomenclature breakdown) or

T4: 0 °C ≤Ta ≤+50 °C for „S“-Typen (item 14 of nomenclature

breakdown)

Ambient rating and temperature code for RS40 types:

T3: −40 °C ≤Ta ≤+70 °C for „T“ or „E“ types (item 14 of

nomenclature breakdown).

T4: −40 °C ≤Ta ≤+60 °C for „T“ or „E“ types (item 14 of

nomenclature breakdown) or

T4: 0 °C ≤Ta ≤+60 °C for „S“ types (item 14 of nomenclature

breakdown)

The modules shall be installed in a suitable enclosure in accordance

with EN 60079-15 providing a degree of protection of at least IP54

according to EN 60529, taking into account the environmental

conditions under which the equipment will be used.

Installation RS20/22/30/32/40

Release

06/2013 9

When the temperature under rated conditions exceeds 70 °C at the

cable or conduit entry point, or 80 °C at the branching point of the

conductors, the temperature specification of the selected cable and

cable entries shall be in compliance with the actual measured

temperature values.

Provisions shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 40 %.

Connectors shall be connected or disconnected exclusively in dead-

voltage state.

DIP switches shall be switched exclusively in dead-voltage state.

The USB port shall remain disconnected.

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

The housing is grounded via the separate ground screw on the bottom left

of the front panel.

WARNING

ELECTRIC SHOCK

Never insert sharp objects (small screwdrivers, wires, etc.) into the inside of

the device.

Never insert sharp objects (small screwdrivers, wires, etc.) into the

connection terminals for the supply voltage or the signal contact, and do not

touch the terminals!

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

CAUTION

OVERHEATING OF THE DEVICE

When installing the device, ensure that the ventilation slots are not covered.

Make sure there is at least 10 cm (3.94 in) of space.

Failure to follow these instructions can result in injury or equipment

damage.

10 Installation RS20/22/30/32/40

Release

06/2013

For the ground conductor, use a cable with a cross section of at least

1.0 mm².

Make sure there is at least 3.94 in (10 cm) of space in front of the

ventilation slits of the housing.

The device must be installed in the vertical position.

If installed in a living area or office environment, the device must be

operated exclusively in switch cabinets with fire protection

characteristics in accordance with EN 60950-1.

Environment

Only operate the device at the specified ambient temperature

(temperature of the surrounding air at a distance of up to 5 cm from the

device) and at the specified relative humidity.

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment within the pollution degree specified

in the technical data.

Qualification requirements for personnel

Qualified personnel as understood in this manual and the warning signs,

are persons who are familiar with the setup, assembly, startup, and

operation of this product and are appropriately qualified for their job. This

includes, for example, those persons who have been:

trained or directed or authorized to switch on and off, to ground and to

label power circuits and devices or systems in accordance with current

safety engineering standards;

trained or directed in the care and use of appropriate safety equipment

in accordance with the current standards of safety engineering;

trained in providing first aid.

General safety instructions

This device is operated by electricity. You must follow precisely the

prescribed safety requirements for the voltage connections in this

document.

See “Supply voltage” on page 4.

See “Supply voltage for PoE power supply units (optional)” on page 5.

Otros manuales para Hirschmann RS20 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Belden

Belden

Belden HIRSCHMANN OCTOPUS OS3 Manual de usuario

Belden

Belden Thinklogical TLX48 Manual de usuario

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series Manual de usuario

Belden

Belden Hirschmann MACH1040 Series Manual de usuario

Belden

Belden Hirschmann SPIDER-SL-20-01T1S29999SZ9HHHH Manual de usuario

Belden

Belden Hirschmann RS20 Series Manual de usuario

Belden

Belden HIRSCHMANN MACH 100 Series Manual de usuario

Belden

Belden HIRSCHMANN BRS20 Manual de usuario

Belden

Belden Hirschmann RS20 Series Manual de usuario

Belden

Belden Hirschmann RS20 Series Manual de usuario

Belden

Belden Hirschmann SPIDER II 8TX Manual de usuario

Belden

Belden HIRSCHMANN SPIDER II Manual de usuario

Belden

Belden Hirschmann MACH1000 Series Manual de usuario

Belden

Belden Hirschmann RS20 U Series Manual de usuario

Belden

Belden MAMMUTHUS MTM2800-PSU120 Manual de usuario

Belden

Belden HIRSCHMANN Octopus II Manual de usuario

Belden

Belden HIRSCHMANN MACH 4000 Series Manual de usuario

Belden

Belden Hirschmann MACH104 Series Guía del usuario

Belden

Belden Hirschmann RED25 Series Manual de usuario

Belden

Belden Hirschmann SPIDER Standard Line Series Manual de usuario

Belden

Belden HIRSCHMANN RSP20 Manual de usuario

Belden

Belden HIRSCHMANN MSP30 Manual de usuario

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Manual de usuario

Belden

Belden ThinkLogical TLX12 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario