Belden HIRSCHMANN SPIDER II Manual de usuario

Installation SPIDER II

Release

10/2013

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Ethernet Rail Switch

SPIDER II, SPIDER II Giga, SPIDER II PoE

SPIDER II 8TX

SPIDER II 8TX EEC

SPIDER II 8TX/1FX EEC

SPIDER II 8TX/1FX-SM EEC

SPIDER II 8TX/1FX-ST EEC

SPIDER II 8TX/2FX EEC

SPIDER II 8TX/2FX-SM EEC

SPIDER II 8TX/2FX-ST EEC SPIDER II Giga 5T/2S EEC SPIDER II Giga 5T EEC

SPIDER II 8TX PoE

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

Installation 039 709-001-07-1013 - 22.10.13

Installation SPIDER II

Release

10/2013 3

Contents

Safety instructions 5

About this Manual 9

Legend 10

1 Description 10

1.1 General device description 10

1.2 Description of the device variants 10

1.3 Ethernet ports 15

1.3.1 10/100 Mbit/s twisted pair port 15

1.3.2 10/100 Mbit/s PoE port 15

1.3.3 10/100/1000 Mbit/s twisted pair port 16

1.3.4 100 Mbit/s F/O port 16

1.3.5 1000 Mbit/s F/O port 17

1.4 Display elements 17

1.4.1 Device state 17

1.4.2 Port state 17

2 Installation 18

2.1 Unpacking the package and checking the content 19

2.2 Installing an SFP transceiver (optional) 19

2.3 Connecting the terminal block for the supply voltage and the

grounding 20

2.4 Mounting the device on the DIN rail 20

2.5 Installing the terminal block, start-up procedure 21

2.6 Connecting network cables 22

2.6.1 10/100 Mbit/s twisted pair port 22

1.3.2 10/100 Mbit/s PoE port 15

2.6.3 10/100/1000 Mbit/s twisted pair port 22

2.6.4 100 Mbit/s F/O port 22

2.6.5 1000 Mbit/s F/O port 22

3 Maintenance and service 23

4Installation SPIDER II

Release

10/2013

4Disassembly 23

4.1 Removing the device from the DIN rail 23

4.1.1 SPIDER II without PoE 23

4.1.2 SPIDER II 8TX PoE 24

4.2 Removing the SFP transceivers 24

5 Technical data 25

A Further Support 35

Installation SPIDER II

Release

10/2013 5

Safety instructions

Correct usage

Only use the device for those purposes specified in the catalog and in the

technical description. Only operate the device with external devices and

components that are recommended and permitted by the manufacturer.

The proper and safe operation of this product depends on proper handling

during transport, proper storage, assembly and installation, and

conscientious operation and maintenance procedures.

Supply voltage

The power supply inputs are designed for operation with safety extra-

low voltage. Solely connect SELV circuits with voltage restrictions in

line with IEC/EN 60950-1 to the supply voltage connections.

Use undamaged parts.

If you are operating the module with an external voltage, only supply

the system with a safety extra-low voltage in compliance with IEC/EN

60950-1.

Connect the ground connector before you set up the other

connections. When removing the connections, you remove the ground

connector last.

Relevant for North America: To be used in class 2 circuits.

The device may only be connected to a supply voltage of class 2 that

fulfills the requirements of the National Electrical Code, Table 11(b).

Relevant for North America: For use in Class 2 circuits

Use copper wire/conductors of class 1 60/75 °C or 75 °C or 90 °C

exclusively.

Relevant for North America

for devices certified for hazardous locations:

Power, input and output (I/O) wiring must be in accordance with

Class I, Division 2 wiring methods [Article 501-4(b) of the National

Electrical Code, NFPA 70] and in accordance with the authority having

jurisdiction.

Only switch on the device when the housing is closed.

CAUTION

ELECTRIC SHOCK

Solely connect a supply voltage that corresponds to the type plate of your

device.

Failure to follow these instructions can result in injury or equipment

damage.

6Installation SPIDER II

Release

10/2013

Shielding ground

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

Note: The device is grounded by means of a 3-pin terminal block.

Verify that the electrical installation meets locally or nationally

applicable safety regulations.

The device must be installed in the vertical position.

If installed in a living area or office environment, the device must be

operated exclusively in switch cabinets with fire protection

characteristics in accordance with EN 60950-1.

CAUTION

ELECTRIC SHOCK

Solely connect a supply voltage that corresponds to the type plate of your

device.

Never insert sharp objects (small screwdrivers, wires, etc.) into the inside of

the device.

Failure to follow these instructions can result in injury or equipment

damage.

CAUTION

OVERHEATING OF THE DEVICE

When installing the device, ensure that the ventilation slots are not covered.

Make sure there is at least 10 cm (3.94 in) of space.

Failure to follow these instructions can result in injury or equipment

damage.

Installation SPIDER II

Release

10/2013 7

Environment

Only operate the device at the specified ambient temperature

(temperature of the surrounding air at a distance of up to 5 cm from the

device) and at the specified relative humidity.

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

The equipment is designed for in building installation only and is not

intended to be connected to exposed (outside plant) networks.

Qualification requirements for personnel

Qualified personnel as understood in this manual and the warning signs,

are persons who are familiar with the setup, assembly, startup, and

operation of this product and are appropriately qualified for their job. This

includes, for example, those persons who have been:

trained or directed or authorized to switch on and off, to ground and to

label power circuits and devices or systems in accordance with current

safety engineering standards;

trained or directed in the care and use of appropriate safety equipment

in accordance with the current standards of safety engineering;

trained in providing first aid.

General safety instructions

This device is operated by electricity. You must follow precisely the

prescribed safety requirements for the voltage connections in this

document.

See “Supply voltage” on page 5.

Non-observance of these safety instructions can cause material damage

and/or injuries.

Only appropriately qualified personnel should work on this device or in

its vicinity. The personnel must be thoroughly familiar with all the

warnings and maintenance procedures outlined in this operating

manual.

The proper and safe operation of this device depends on proper

handling during transportation, proper storage and assembly, and

conscientious operation and maintenance procedures.

Never start operation with damaged components.

Only use the devices in accordance with this manual. In particular,

observe all warnings and safety-related information.

Any work that may be required on the electrical installation may only

be carried out by personnel trained for this purpose.

8Installation SPIDER II

Release

10/2013

Relevant for SPIDER II 8 TX/...FX... EEC and SPIDER II Giga 5T/2S

EEC:

Note: LED or LASER components in compliance with IEC 60825-1

(2007):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

National and international safety regulations

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2004/108/EC (EMC)

Directive of the European Parliament and the council for standardizing the

regulations of member states with regard to electromagnetic

compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55022

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

Installation SPIDER II

Release

10/2013 9

E marking

The labeled devices comply with the regulations contained in the following

European directive(s):

72/245/EWG, 2009/19/EG

Guideline for standardizing the regulations of member states relating to

radio interference from motor vehicles. Certified devices are marked with

an e1 type approval indicator.

Rule No. 10 of the Economic Commission for Europe (ECE): Devices with

a certification are labelled with the E type-approval mark.

Note: For use in connection with a suitable type approved power supply

only.

FCC note

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate high

frequencies, and if it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a living area can also cause interference, and in this case

the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

10 Installation SPIDER II

Release

10/2013

About this Manual

The “Installation User Manual” document contains a device description,

safety instructions, a display description and other information that you

require to install the device before starting with the configuration of the

device.

Legend

The symbols used in this manual have the following meanings:

Listing

Work step

Subheading

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Belden

Belden

Belden Hirschmann RED25 Series Manual de usuario

Belden

Belden Hirschmann MACH4002 Series Manual de usuario

Belden

Belden Hirschmann HiOS-2S Manual de usuario

Belden

Belden HIRSCHMANN HiOS-2A Manual de usuario

Belden

Belden Hirschmann RS20 Series Manual de usuario

Belden

Belden Hirschmann MACH1040 Series Manual de usuario

Belden

Belden lumberg automation 0960 IOL 3816-001 Manual de usuario

Belden

Belden HIRSCHMANN OCTOPUS OS3 Manual de usuario

Belden

Belden HIRSCHMANN MSP30 Manual de usuario

Belden

Belden Hirschmann GREYHOUND GRS1042 Manual de usuario

Belden

Belden HIRSCHMANN OCTOPUS OS20 Series Manual de usuario

Belden

Belden Hirschmann RS20 Series Manual de usuario

Belden

Belden Hirschmann MACH104-PoEP Series Manual de usuario

Belden

Belden Grass Valley Kayenne Suplemento

Belden

Belden ThinkLogical TLX12 Manual de usuario

Belden

Belden HIRSCHMANN Octopus II Manual de usuario

Belden

Belden HIRSCHMANN MACH 100 Series Manual de usuario

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series Manual de usuario

Belden

Belden grass valley GV FABRIC Manual de usuario

Belden

Belden Hirschmann MACH102 Series Manual de usuario

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manual de usuario

Belden

Belden Hirschmann RS20 Series Manual de usuario

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Manual de usuario

Belden

Belden Hirschmann SPIDER 8TX EEC Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario