Belden HIRSCHMANN BRS20 Manual de usuario

Installation BRS20/22/30/32/40/42/50/52

Release

01/2022

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Ethernet Industrial Ethernet BOBCAT Rail Switch

BRS20/22/30/32/40/42/50/52

1/20/22 Installation BRS20/22/30/32/40/42/50/52

Release

01/2022

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at:

https://www.doc.hirschmann.com

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation BRS20/22/30/32/40/42/50/52

Release

01/2022 3

Contents

Important information 6

Safety instructions 8

About this manual 22

Key 23

1 Description 24

1.1 General device description 24

1.2 Device name and product code 25

1.3 Device views 30

1.3.1 Front view 30

1.3.2 Rear view 33

1.4 Power supply 34

1.4.1 Supply voltage with characteristic value T 34

1.4.2 Supply voltage with characteristic value F 34

1.4.3 Supply voltage with characteristic value U 34

1.4.4 Supply voltage with characteristic value P 34

1.5 Ethernet ports 35

1.5.1 10/100 Mbit/s twisted pair port 35

1.5.2 10/100/1000 Mbit/s twisted pair port 35

1.5.3 100/1000/2500 Mbit/s twisted pair port 35

1.5.4 100 Mbit/s F/O port 37

1.5.5 100/1000 Mbit/s F/O port 37

1.5.6 100/1000/2500 Mbit/s F/O port 37

1.5.7 Support of PoE(+) 38

1.6 Display elements 39

1.6.1 Device state 39

1.6.2 Port status 40

1.7 Management interfaces 43

1.7.1 Signal contact 43

1.7.2 USB-C interface 44

1.7.3 Digital input 45

1.7.4 Hardware revision 46

4Installation BRS20/22/30/32/40/42/50/52

Release

01/2022

2 Installation 47

2.1 Checking the package contents 47

2.2 Installing and grounding the device 47

2.2.1 Installing the device onto the DIN rail 47

2.2.2 Grounding the device 49

2.2.3 Connecting the ferrite (optional) 49

2.3 Installing an SFP transceiver (optional) 50

2.4 Connecting the terminal blocks 50

2.4.1 Power supply 50

2.4.2 Signal contact (optional) 55

2.4.3 Digital input (optional) 56

2.5 Operating the device 57

2.6 Connecting data cables 58

2.7 Filling out the inscription label 58

3 Making basic settings 59

3.1 First login (Password change) 59

4 Monitoring the ambient air temperature 61

5 Maintenance and service 62

6Disassembly 63

6.1 Removing an SFP transceiver (optional) 63

6.2 Removing the device 64

7 Technical data 65

7.1 General data 65

7.2 Temperature ranges 72

7.3 Supply voltage 76

7.4 Power consumption/power output 79

7.5 Signal contact 80

7.6 Digital input 81

7.7 Climatic conditions during operation 82

7.8 Climatic conditions during storage 83

Installation BRS20/22/30/32/40/42/50/52

Release

01/2022 5

7.9 Dimension drawings 84

7.9.1 Device variants with casing with characteristic

value C (plastic casing) 84

7.9.2 Device variants with casing with characteristic

value E/D (metal casing) 87

7.10 Immunity 90

7.11 Electromagnetic compatibility (EMC) 90

7.12 Network range 92

7.12.1 10/100/1000 Mbit/s twisted pair port 92

7.12.2 Fast Ethernet SFP transceiver 92

7.12.3 Gigabit Ethernet SFP transceiver 94

7.12.4 2.5 Gigabit Ethernet SFP transceiver 96

7.12.5 Bidirectional Fast Ethernet SFP transceiver 97

7.12.6 Bidirectional Gigabit Ethernet SFP transceiver 97

7.13 Derating due to SFP transceiver 98

7.13.1 Fast Ethernet SFP transceiver 98

7.13.2 Gigabit Ethernet SFP transceiver 99

7.13.3 2.5 Gigabit Ethernet SFP transceiver 100

7.13.4 Bidirectional Fast Ethernet SFP transceiver 101

7.13.5 Bidirectional Gigabit Ethernet SFP transceiver 101

8 Scope of delivery 102

9 Accessories 103

9.1 General accessories 103

9.2 Order numbers for standard variants 103

9.3 Fast Ethernet SFP transceiver 105

9.4 Gigabit Ethernet SFP transceiver 106

9.5 2.5 Gigabit Ethernet SFP transceiver 107

9.6 Bidirectional Fast Ethernet SFP transceiver 107

9.7 Bidirectional Gigabit Ethernet SFP transceiver 108

10 Underlying technical standards 109

A Further support 110

6Installation BRS20/22/30/32/40/42/50/52

Release

01/2022

Important information

Note: Read these instructions carefully, and familiarize yourself with the

device before trying to install, operate, or maintain it. The following notes may

appear throughout this documentation or on the device. These notes warn of

potential hazards or call attention to information that clarifies or simplifies a

procedure.

Symbol explanation

This is a general warning symbol. This symbol alerts you to

potential personal injury hazards. Observe all safety notes that

follow this symbol to avoid possible injury or death.

If this symbol is displayed in addition to a safety instruction of the

type “Danger” or “Warning”, it means that there is a danger of

electric shock and failure to observe the instructions will

inevitably result in injury.

This symbol indicates the danger of hot surfaces on the device.

In connection with safety instructions, non-observance of the

instructions will inevitably result in injuries.

DANGER

DANGER draws attention to an immediately dangerous situation, which will

inevitably result in a serious or fatal accident if not observed.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION indicates a possible danger which, if not avoided, may result in

minor injuries.

Installation BRS20/22/30/32/40/42/50/52

Release

01/2022 7

NOTICE

NOTE provides information about procedures that do not involve the risk of

injury.

8Installation BRS20/22/30/32/40/42/50/52

Release

01/2022

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 65.

Connect to the product only components suitable for the requirements

of the specific application case.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow this instruction can result in death, serious injury, or

equipment damage.

Installation BRS20/22/30/32/40/42/50/52

Release

01/2022 9

Installation site requirements

Install this device only in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

See “Technical data” on page 65.

Strain relief

Note: If the strain relief is insufficient, there is a potential risk of torsion,

contact problems and creeping interruptions.

Relieve the connection points of cables and lines from mechanical

stress.

Design strain reliefs in such a way that they help prevent any

mechanical damage to cables, wires or conductors caused by external

influences or their own weight.

To help prevent damage to device connections, connectors and

cables, follow the instructions for proper installation in accordance with

DIN VDE 0100-520:2013-06, sections 522.6, 522.7 and 522.13.

WARNING

FIRE HAZARD

If you connect the device to a power supply that does NOT meet the

requirements for Limited Power Source, NEC Class 2 or PS2 according to

IEC/EN 62368-1 and is NOT limited to 100 W output power, the device

must be installed in either a switch cabinet or other fire enclosure.

The fire enclosure can be made of metal or plastic with fire-protection

properties of at least V-1 according to IEC 60695-11-10. Bottom openings

of the fire enclosure must NOT exceed 2 mm in diameter.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

10 Installation BRS20/22/30/32/40/42/50/52

Release

01/2022

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Shielding ground

The shielding ground of the connectable twisted pair cables is connected

to the ground connection as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Grounding the device

The device is grounded via the separate ground screw. The grounding

screw is located on the front right side of the device for narrow casing

sizes. For the medium and wide casing sizes, the grounding screw is

located at the bottom left of the front side of the device.

See “Dimension drawings” on page 84.

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

The following requirements apply without restrictions:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

Only use power supply cables that are suitable for a temperature 20 °C (36 °F)

higher than the maximum ambient air temperature at which the device is used.

Only use copper wire.

Otros manuales para HIRSCHMANN BRS20

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Belden

Belden

Belden HIRSCHMANN MSP30 Manual de usuario

Belden

Belden Hirschmann GREYHOUND GRS1042 Manual de usuario

Belden

Belden Hirschmann Rail Switch Power Lite Manual de usuario

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manual de usuario

Belden

Belden HIRSCHMANN HiOS-2A Manual de usuario

Belden

Belden Hirschmann RS20 Series Manual de usuario

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manual de usuario

Belden

Belden Hirschmann MICE MS20 Manual de usuario

Belden

Belden HIRSCHMANN OCTOPUS OS20 Series Manual de usuario

Belden

Belden Hirschmann MACH104-PoEP Series Manual de usuario

Belden

Belden HIRSCHMANN MACH 4000 Series Manual de usuario

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series Manual de usuario

Belden

Belden grass valley GV FABRIC Manual de usuario

Belden

Belden Hirschmann HiOS-2S Manual de usuario

Belden

Belden HIRSCHMANN SPIDER II Manual de usuario

Belden

Belden MAMMUTHUS MTM2800-PSU120 Manual de usuario

Belden

Belden Hirschmann IT MAMMUTHUS MTS26 Series Manual de usuario

Belden

Belden Hirschmann MACH1040 Series Manual de usuario

Belden

Belden Hirschmann MACH104-PoEP Series Manual de usuario

Belden

Belden ThinkLogical TLX12 Manual de usuario

Belden

Belden HIRSCHMANN GREYHOUND GRM Series Manual de usuario

Belden

Belden Hirschmann SPIDER II 8TX Manual de usuario

Belden

Belden Hirschmann GREYHOUND GRS1042 Manual de usuario

Belden

Belden Hirschmann MACH104 Series Guía del usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario