Badger Meter Blancett B3000 Series Manual de usuario

Digital Flow Monitors

Service Kits for B3000 Basic and Advanced

Explosion-Proof Monitors

DSY-UM-02582-EN-04 (June 2018) User Manual

CONTENTS

Scope of This Manual � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Unpacking and Inspection � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Safety � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Electrical Symbols � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4

Service Kit Parts Installation� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4

Replacing the CPU Board � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4

Replacing the Display Board � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6

Testing the Display Buttons � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8

Service Kits for B3000 Basic and Advanced Explosion-Proof Monitors

Page ii June 2018DSY-UM-02582-EN-04

Scope of This Manual

Page 3June 2018 DSY-UM-02582-EN-04

SCOPE OF THIS MANUAL

This manual provides instructions for installing these service kit parts for the B3000

explosion-proof flow monitor:

• B300-103 Explosion-Proof CPU for Basic B3000 flow monitors

• B300-104 Explosion-Proof CPU for Advanced B3000 flow monitors

• B300-106 Explosion-Proof Display PCB

MPORTANTI

• Any board must be replaced with an equivalent certified replacement part. You must

contact Badger Meter for an appropriate replacement part.

• Repairs are only allowed to be carried out by the manufacturer or an authorized

Badger Meter agent.

• Must be aware of proper ESD procedures and protocols. Any work must be done in an ESD

approved environment.

• For any questions on installation, service replacements and other repairs contact

Badger Meter.

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATICSENSITIVE DEVICES.

UNPACKING AND INSPECTION

Upon opening the shipping container, visually inspect the product and applicable

accessories for any physical damage such as scratches, loose or broken parts, or any other

sign of damage that may have occurred during shipment�

OTE:NIf damage is found, request an inspection by the carrier’s agent within 48 hours of

delivery and file a claim with the carrier� A claim for equipment damage in transit

is the sole responsibility of the purchaser�

SAFETY

EXPLOSION HAZARD  SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR

CLASS I, DIVISION 2.

AVERTISSMENT

RISQUE D’EXPLOSION  LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE

CEMATÉRIEL INACCCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, DIVISION 2.

DO NOT CONNECT OR DISCONNECT EITHER POWER OR OUTPUTS UNLESS THE AREA IS

KNOWN TO BE NONHAZARDOUS.

AVERTISSMENT

RISQUE D’EXPLOSION. NE PAS DÉBRANCHER TANT QUE LE CIRCUIT EST SOUSTENSION,

À MOINS QU’LL NE S’AGISSE D’UN EMPLACEMENT NON DANGEREUX.

Service Kit Parts Installation

Page 4 June 2018DSY-UM-02582-EN-04

Electrical Symbols

Function Direct

Current Alternating

Current Earth

(Ground) Protective

Ground Chassis Ground

Symbol

SERVICE KIT PARTS INSTALLATION

DANGER

REMOVE DEENERGIZE ANY EXTERNAL POWER FROM THE UNIT BEFORE REMOVING

THE SCREW COVER FROM THE ENCLOSURE. FAILURE TO DO SO CAN BE DANGEROUS.

Replacing the CPU Board

Service Kit Number B300-103 for the Explosion-Proof basic monitor contains:

• One programmed, explosion-proof CPU PCB, PN B300014-T

• Four screws, Phillips tri-shank, #4-20 × 1/4, zinc/steel, PN B300113

Service Kit Number B300-104 for the Explosion-Proof advanced monitor contains:

• One programmed, explosion-proof CPU PCB, PN B300017-T

• Four screws, Phillips tri-shank, #4-20 × 1/4, zinc/steel, PN B300113

This procedure applies to both Basic and Advanced Explosion-Proof B3000 models�

1� Grasp the enclosure cover and turn it counter-clockwise until it separates from the

enclosure body� Set the cover aside�

2� Loosen the two thumb screws and slightly turn the circuit board assembly far enough

to access the battery connector�

3.6 VOLTS

TADRAN

LITHIUM

INORGANIC

BATTORY

Enter

Down

COM

12 1

Thumb Screws

COM 12

Total Flow

Reset Key

Service Kit Parts Installation

Page 5June 2018 DSY-UM-02582-EN-04

3� Press the tab on the battery connector plug to release it from the P2 battery

connector socket�

4� Record the locations of all wiring connected to the CPU board�

5� Remove all wiring from the CPU board�

6� Remove the 4 screws holding the CPU board�

7� Pull the CPU board straight up to unhook the J1 terminal block from the pins of the

display board P1 connector�

8� Align the new CPU board J1 terminal block with the pins of the display board P1

connector� Gently press the boards together making sure not to bend the pins� Align

the screw holes in the housing with the screw holes of new CPU board�

9� Secure the new CPU board with 4 screws�

10� Attach the battery connector plug to the P2 battery connector socket on the new

CPU board�

11� Connect the wiring to the new CPU board�

12� Screw on the enclosure cover�

Service Kit Parts Installation

Page 6 June 2018DSY-UM-02582-EN-04

Replacing the Display Board

Service Kit Number B300-106 for the Explosion-Proof display contains:

• One explosion-proof display PCB, PN B300024

• Five screws, Phillips tri-shank, #4-20 × 1/4, zinc/steel, PN B300113

1� Grasp the enclosure cover and turn it counter-clockwise until it separates from the

enclosure body� Set the cover aside�

2� Remove the TOTAL FLOW RESET key from the display housing by pulling it straight out�

Set it aside�

3.6 VOLTS

TADRAN

LITHIUM

INORGANIC

BATTORY

Enter

Down

COM

12 1

Thumb Screws

COM 12

Total Flow

Reset Key

3� Loosen the two thumb screws and slightly turn the circuit board assembly far enough

to access the battery connector�

4� Press the tab on the battery connector plug to release it from the P2 battery

connector socket�

5� Remove the 4 screws holding the CPU board�

Service Kit Parts Installation

Page 7June 2018 DSY-UM-02582-EN-04

6� Pull the CPU board straight up to unhook the J1 terminal block from the pins of the

display board P1 connector� Set it aside�

7� Remove the 5 screws holding the display board�

8� Lift out the display board and discard it�

9� Place the new display board in the holder and attach it with 5 screws�

10� Align the CPU board J1 terminal block with the pins of the new display board P1

connector� Gently press the boards together making sure not to bend the pins� Align

the screw holes in the housing with the screw holes of CPU board�

11� Secure the CPU board with 4 screws�

12� Attach the battery connector plug to the P2 battery connector socket on the CPU board�

13� Re-install the TOTAL FLOW RESET you removed in Step 2� Insert it through the display

housing and into the reset key connector of display board� Orient the at side of the key

toward the display to align it with the square side of the reset key cutout in the cover

plate� Do not push the reset button in too far� The button works best when it touches

the enclosure cover glass, so leaving it up slightly allows it to contact the glass and be

seated as the cover is screwed on�

3.6 VOLTS

TADRAN

LITHIUM

INORGANIC

BATTORY

Enter

Down

COM

12 1

Down

COM 12

Reset Key

Connector

14� Screw on the enclosure cover�

Service Kits for B3000 Basic and Advanced Explosion-Proof Monitors

www.badgermeter.com

BLANCETT is a registered trademark of Badger Meter, In� Other trademarks appearing in this document are the property of their respective entities� Due to

continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except

Control. Manage. Optimize.

Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | +421-2-44 63 83 01

Testing the Display Buttons

COM 12

Bottom Buttons

Top Buttons

MENU Button

1� Press both of the bottom buttons at the same time� If these two buttons are working

properly, the screen displays setup information�

2� Press both of the top buttons at the same time� If these two buttons are working

properly, the screen displays a total reset�

3� Press the MENU button on the top left twice to reset the PCB to display

battery full charge:

◊ The first time you press MENU, the display shows “FLUID”�

◊ The second time you press MENU, the display shows “SAVING”, then goes blank

for a couple of seconds�

4� Screw the enclosure cover onto the enclosure bottom until it seats tightly� Do not

tighten the enclosure set screw�

5� Wait at least 90 seconds after installing the enclosure cover, then place your finger on

enclosure glass over the TOTAL FLOW RESET button� The battery charge indicator

outline flashes off and on when button is activated, even if the parameter is disabled�

1Battery

Indicator

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Badger Meter

Badger Meter

Badger Meter Blancett B2800 Standard Manual de usuario

Badger Meter

Badger Meter RCM 2000 Manual de usuario

Badger Meter

Badger Meter Vortex VN2000 Manual de usuario

Badger Meter

Badger Meter CORIOLIS RCT1000 Manual de usuario

Badger Meter

Badger Meter 380CS Manual de usuario

Badger Meter

Badger Meter Data Industrial 3000 Series Manual de usuario

Badger Meter

Badger Meter Blancett QuickSert B131C-038 Manual de usuario

Badger Meter

Badger Meter Oval Gear LM OG Series Manual de usuario

Badger Meter

Badger Meter FC-5000 Manual de usuario

Badger Meter

Badger Meter epm-3 Manual de usuario

Badger Meter

Badger Meter FMS-3 Manual de usuario

Badger Meter

Badger Meter ORION Manual de usuario

Badger Meter

Badger Meter M-series Manual de usuario

Badger Meter

Badger Meter MN-MR100 Instrucciones y recetas

Badger Meter

Badger Meter E Series Manual de usuario

Badger Meter

Badger Meter ILR710 Manual del propietario

Badger Meter

Badger Meter M5000 Manual de usuario

Badger Meter

Badger Meter iSonic 4000 Manual de usuario

Badger Meter

Badger Meter Impeller Data Industrial 228PV Series Manual de usuario

Badger Meter

Badger Meter Cox Manual de usuario

Badger Meter

Badger Meter Blancett B290-901 Manual de usuario

Badger Meter

Badger Meter Recordall Turbo Series Manual de usuario

Badger Meter

Badger Meter Primo Advanced BMAG-350-icpf Manual

Badger Meter

Badger Meter Blancett B2900 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario