AWS BT2-201 Manual de usuario
BT2-201 (200g x 0.01g)
BT2-1KG (1000g x 0.1g)
User Manual
BT2-Series
Copyright © 2010 American Weigh Scales, Inc.
All rights reserved. Rev. 2.0
BT2-Series
Thank you for purchasing the American Weigh
BT2-Series digital pocket scale. Please read all operating
instructions carefully before use. Scales are precision
measuring devices and should always be handled with
proper care. To ensure years of reliable service, keep these
simple tips in mind:
• Do not exceed the scale’s maximum capacity.
Overloading your scale can permanently damage it!
• Avoid exposure to extreme heat or cold. Scales
perform best at normal room temperature. If
temperatures have changed dramatically, calibration
and adjustment may be necessary.
• Allow your scale to warm up for 30-60 seconds before
performing calibration and adjustment(if available).
• Store your scale in a clean, dry location. Dust, dirt,
and moisture can accumulate on the weighing
sensors and electronics causing inaccuracy or
malfunction.
• Avoid using your scale in close proximity to strong
radio wave emitting devices such as computers, cash
registers, and cordless phones.
• Alwaysweighonaatandlevelsurface,freefrom
vibrations and drafts. The corner of a room is usually
the most stable.
• Gently apply all items to be weighed. Do not drop
items onto the weighing platform.
• Avoid dropping your scale. The warranty does not
cover damage due to rough treatment or overload.
• Checkthebatteriesrstifyouarehavinganytrouble
with your scale. This simple step can remedy most
scale issues.
• Do not disassemble your scale. This product contains
no user serviceable parts.
I. Part List
1. Scale
2. Removable Cover/Expansion Tray
3. AAA Batteries (x2)
II. Key Description
III. Battery Installation
1. Beforeusingthescaleforthersttime,check
the battery compartment and remove any plastic
insulation strips or packaging that may be in place to
prevent battery drainage during shipping/storage.
2. If you are replacing the batteries, make sure the
positive and negative contacts are properly aligned.
Mode Key
Tare Key
Weight Indicator
ON/OFF Key
BT2-Series
IV. Operation
1. Placethescaleonaat,levelsurfaceandpressthe
I/O key to turn the scale on.
2. Once the start-up process completes and the scale
goes to zero you are ready to weigh.
3. Place the quantity to be weighed onto the weighing
platform.
4. Wait a couple seconds for the display to stabilize
before taking a weight reading.
V. Changing the Unit of Measure
1. Press the Mkey to change the scales displayed unit
of measure.
2. If the scale is turned off then back on, it will default
to the last unit used.
• BT2-201 & BT2-1KG Units: g (gram) oz (ounce)
ozt (troy ounce) dwt (pennyweight) ct (carat)
gn (grain)
VI. Using the Tare Feature
You can use this scale’s tare feature to subtract the weight
of an empty container or vessel for net weight determination.
NOTE: The weight of the container will subtract from the
available capacity.
1. Place the empty container or vessel on the weighing
platform.
2. Press the Tkey once. The display will then reset to
zero. If the container is removed, it’s weight will be
displayed as a negative number.
3. Youmaynowllthecontainerwiththequantityto
be weighed. The display will show the net weight of
the contents.
4. To return to normal weight display (gross weight),
remove any items from the weighing platform and
press the T key again to re-zero the scale.
VII. Calibration
Calibration and adjustment are performed at the factory.
However, the weighing range can shift slightly during
shipping. Also, due to changes in local acceleration of gravity
around the world, adjustment is recommended when moving
the scale from one location to another. To check calibration:
1. Place the required calibration weight on the scale
and note the displayed value.
2. If the displayed value is not within acceptable
tolerance (see chart below), adjustment is required.
Model Acceptable
Tolerance (±)
Calibration
Weight
Recommended
Accuracy Class
BT2-201 0.01g 200g, 100g* OIML M2
BT2-1KG 0.1g 500g, 100g* OIML M2
*Selectable at calibration time
VIII. Adjustment
1. Press and hold the Mkey until the display shows
“CAL”.
2. Press the Mkeyagain.Thedisplaywillash“CAL”
followed by the calibration weight value (see chart).
3. Place the calibration weight on the center of the
weighing platform.
4. Once the weight is accepted, the display will show
“PASS” then return to normal operation. NOTE: If
BT2-Series
you would prefer to use a 100g weight instead of the
default weight, you can press and hold the Tkey to
change the calibration weight value before placing
the weight on the platform.
IX. Troubleshooting
• Problem: Scale will not turn on
• Solution: Check the batteries
• Problem: Displayedweightuctuatesrandomly
• Solution: Make sure your workspace is stable and
free of any air currents or vibration
• Problem: Displayed weight is inaccurate
• Solution: Perform a calibration adjustment
X. Error Codes
1. OUTZ - Zero range has shifted. Perform calibration
adjustment. If the problem persists, the load cell may
be permanently damaged due to overloading.
2. 88888 - Maximum capacity exceeded. Remove the
extra weight to avoid damaging the load cell.
3. L - Batteries are low. Replace the batteries.
BT2-201 BT2-1KG
Max. Capacity 200g 1000g
Readability 0.01g 0.1g
Min. Weight 0.03g 0.2g
Power 2 x AAA
Dimensions 0.7 x 3.0 x 5.0”
Platform Dimensions 2.5 x 2.7”
Warranty 10 Year Limited Warranty
XI. Capacity/Readability Charts
BT2-201 BT2-1KG
200g x 0.01g
7.05oz x 0.001oz
6.43ozt x 0.001ozt
128.6dwt x 0.01dwt
1000ct x 0.05ct
3086gn x 0.2gn
1000g x 0.1g
35.27oz x 0.01oz
32.15ozt x 0.01ozt
643.0dwt x 0.1dwt
5000ct x 0.5ct
15432gn x 2gn
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Escala de AWS
AWS
AWS CHROME-1KG Manual de usuario
AWS
AWS 330SW Manual de usuario
AWS
AWS AMW-500i Manual de usuario
AWS
AWS CITRON-5K Manual de usuario
AWS
AWS TL-330 (330lb x 0.2lb) Manual de usuario
AWS
AWS EPSILON EP-5KG Manual de usuario
AWS
AWS AT Series Manual de usuario
AWS
AWS DIA-20 Manual de usuario
AWS
AWS EDGE Manual de usuario
AWS
AWS AWS-70 Manual de usuario
AWS
AWS AMW-810 Manual de usuario
AWS
AWS Bioweight Manual de usuario
AWS
AWS MSL-180 Manual de usuario
AWS
AWS PEPPER-5K Manual de usuario
AWS
AWS AMW-50 Manual de usuario
AWS
AWS IDOL-100 Manual de usuario
AWS
AWS SR-1KG Manual de usuario
AWS
AWS 330LPW Instrucciones de montaje
AWS
AWS PW-44 Manual de usuario
AWS
AWS ECOWEIGH Series Manual de usuario
