Avocent Cybex SwitchView Manual de usuario

Powering your system

Locate the power cord that came with your switch.

Plug one end into the IEC power connector on

the SwitchView SC8 DVI switch. Make sure that

the power switch is off, then plug the other end

of the power cord into an appropriate AC wall

outlet. Power up your switch ﬁrst, then power up all

attached servers.

The Power of Being There®

Quick Installation Guide

Cybex®SwitchView®

SC8 DVI Switch

The following instructions will help you

install and use your SwitchView SC8

DVI switch.

Should you require further assistance, please

contact Avocent Technical Support.

To install the Cybex SwitchView SC8 DVI switch

To Contact Avocent Technical Support CALL (888) 793-8763 VISIT www.avocent.com/support DOWNLOAD www.avocent.com

Avocent, the Avocent logo, The Power of Being There, Cybex and SwitchView are registered trademarks of Avocent Corporation or its afﬁliates. ©2005 Avocent Corporation. All rights reserved. 590-502-501A

Connecting your local peripherals to

the SwitchView SC8 DVI switch

Power down all servers that will be part of your

SwitchView SC8 DVI switching system. Locate

your PS/2 keyboard, DVI monitors and PS/2

mouse.

Plug your DVI monitor cables into the

CONSOLE ports on the left side of the back

of your switch

. Plug your PS/2 keyboard cable

and your PS/2 mouse cable into the keyboard

and mouse ports respectively.

Connecting your servers to the

SwitchView SC8 DVI switch

Locate your ﬁrst cable set consisting of two

PS/2 cables and one or two DVI cables. The

SwitchView SC8 DVI switching system has eight

port sets labeled A-H on the rear of the unit. Plug

one end of the two PS/2 cables (keyboard and

mouse) and one end of a DVI cable (monitors)

into the corresponding ports on your computer.

Plug the other ends into any available server port

set on yourSwitchView SC8 DVI switching system.

Repeat this process until all servers are properly

attached to the SwitchView SC8 DVI switch.

CONSOLE HG F E DCBA

Power down all

connected servers.

Connect your

peripherals to the

CONSOLE ports

on the switch.

Connect the eight

servers to the

switch with the

provided cables.

Press the

appropriate front

panel button

labeled A-H to

access servers in

your system.

Switching your servers

Press the appropriate front panel button labeled

A-H to access another server in your SwitchView

switching system.

Power up

your system.

USA Notiﬁcation

Warning: Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Canadian Notiﬁcation

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Safety and EMC

Approvals and Markings

UL, FCC, cUL, ICES-003

Safety Precautions

NOTE: The AC inlet is the main disconnect.

INSTRUCTIONS

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

DANGEROUS VOLTAGE

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s

enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.

RACK MOUNT SAFETY CONSIDERATIONS

• Elevated Ambient Temperature: If installed in a closed rack assembly, the operation temperature of the rack

environment may be greater than room ambient. Use care not to exceed the rated maximum operating temperature of

40° C for this product.

• Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of airﬂow required for safe

operation of the equipment is not compromised.

• Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not

achieved due to uneven mechanical loading.

• Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and

the effect that overloading of circuits might have on overcurrent protection and supply wiring. Consider equipment

nameplate ratings for maximum current.

• Reliable Earthing: Reliable earthing of rack mounted equipment should be maintained. Pay particular attention to

supply connections other than direct connections to the branch circuit (for example, use of power strips).

Este manual sirve para los siguientes modelos

Otros manuales de Cambiar de Avocent

Avocent

Avocent ESP Multi-Interface Serial Hub SuperSerial Manual de usuario

Avocent

Avocent DSR DSR800 Instrucciones de instalación y mantenimiento

Avocent

Avocent AutoView 1000R Instrucciones de instalación y mantenimiento

Avocent

Avocent DSR Series DSR1030 Manual de usuario

Avocent

Avocent AMX5000 Manual de usuario

Avocent

Avocent AutoView 3100 Manual de usuario

Avocent

Avocent AutoView 2020 Manual de usuario

Avocent

Avocent SwitchView 130 Manual de usuario

Avocent

Avocent AMX Switch Series Instrucciones de instalación y mantenimiento

Avocent

Avocent SwitchView IP 1020 Instrucciones de instalación y mantenimiento

Avocent

Avocent 115B Instrucciones de instalación y mantenimiento

Avocent

Avocent SwitchView SC120 Manual de usuario

Avocent

Avocent DSR Series DSR1020 Manual de instrucciones

Avocent

Avocent AutoView xx15 Series Manual técnico

Avocent

Avocent AMX 5130 Manual de usuario

Avocent

Avocent DSR Series DSR1021 Manual de usuario

Avocent

Avocent MPU1016DAC-001 Manual de usuario

Avocent

Avocent AMX5000 Manual de usuario

Avocent

Avocent AutoView 1000R Instrucciones de instalación y mantenimiento

Avocent

Avocent SWITCHVIEW PC Manual de usuario

Avocent

Avocent DSR Series DSR1020 Manual de instrucciones

Avocent

Avocent DSR SWITCH - Instrucciones de instalación y mantenimiento

Avocent

Avocent DSR Series DSR1031 Manual de instrucciones

Avocent

Avocent DSR4010 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario