Atdec AWM-A13 Manual de usuario

AWM-A13 Page 1 of 4

Installation Guide

AWM-A13

130 Arm

COMPONENT CHECKLIST REQUIRED TOOLS

WEIGHT RANGE

Monitor

arm

(x1)

Channel

clamp

(x1)

VESA

head

(x1)

Screw

M4x12mm

(x4)

Screw

M4x10mm

(x4)

Screw

M4x8mm

(x4)

Spacer

10mm

(x4)

Security

screw

(x4)

4mm

allen key

(x4)

0 - 12kg

(0 - 26.5lbs)

• Phillips Head Screwdriver

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with Atdec modular (AWM) products.

AWM-A13 Page 2 of 4

2. Fit arm onto channel clamp

1. Optional 180� rotation limiter

3. Mounting arm assembly

2.1 Push arm onto clamp

1.1 Remove plastic sleeve

2.2 Ensure arm is fully pushed onto clamp

1.2 Remove rotation ring

2.3 Lightly tighten set screw

1.3 Place rotation ring in

desired orientation/position

Note: Place the rotation ring

depending on what post channel

the arm will be attached to. The tag

should always face towards the user

1. Press

2. Lift

180°

360°

Default

Position

Flipped

Position

Tag

3.1 Slide arm assembly into channel 3.2 Move to desired height

Fit top cap on post

Note: Ensure

clamp lever is

vertical and

unlocked

Note: Squeeze and

hold clamp jaws before

inserting into channel Post

3.3 Lock at preferred height

by pushing lever down

Wall Channel

‘Click’

Note that the arm is set to rotate 360� by default. To reduce the arm’s rotation to 180�, follow the steps below.

Tip: Check that

rotation of the

arm is smooth

AWM-A13 Page 3 of 4

4. Attach VESA head to monitor

100mm

75mm

100mm 75mm

Flush Spacer

4.1 Screw the VESA head onto monitor

Note spacers may be required for

curved, recessed or uneven monitor

surfaces.

4.2 Ensure the monitor is attached correctly 4.3 VESA mounting compatibility

100mm

75mm

100mm 75mm

Flush Spacer

For other sizes, use a suitable adaptor plate

Tighten

Loosen

Tighten

Loosen

5. Mount monitor

Monitor arm

5.1 Insert VESA head into the monitor arm 5.3 Push the lever down to secure

it to the arm assembly

5.2 Ensure that the VESA head sits flush within

the monitor arm. There should be no gap

Gap No gap

6. Adjust tilt tension & Install security screw

6.1 To make for easy tilt adjustment and to prevent the monitor

from falling forward, adjust the tension as show below

Note: Support

monitor while

adjusting

6.2 OPTIONAL security screw

To install the optional security screw tilt the head upwards

AWM-A13 Page 4 of 4

6. Monitor arm cable management

Note: The cable cover shown,

does not come with all posts

7.4 To reposition the cable cover, pull it

straight up and out of the post and insert

it into any of the available channels

Cable cover

Cable

Cover

Desk

Clamp

7.1 Push the cable down into the cable clip

Note: Cable clips do not

come with all posts

7.6 Feed remaining cable into cover7.5 Loop cable and insert into cable cover

7.2 Push cable clip into post channel

7. Post cable management

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Alternative cable

cover positions

7.3 Recommended post cable cover

position for double or triple arm set-ups

6.1 Plug cables into the

monitor and route the cables

down the arm using the cable

hooks and clips

Important:

Ensure enough cable slack is given

to allow for movement of the monitor

Tabla de contenidos

Otros manuales de Rack y soporte de Atdec

Atdec

Atdec AWM-W35 Manual de usuario

Atdec

Atdec AWM-LR Manual de usuario

Atdec

Atdec TELEHOOK 12/30 Multi Manual de usuario

Atdec

Atdec AWMS-2-BT75-FS Manual de usuario

Atdec

Atdec Focus VF-AT-NP Manual de usuario

Atdec

Atdec A-STSWW-A Manual de usuario

Atdec

Atdec AWM-BT Manual de usuario

Atdec

Atdec AWMS-2-D13-C Manual de usuario

Atdec

Atdec AWMS-2-BT75-H Manual de usuario

Atdec

Atdec AWMS-2-BT75-FS Manual de usuario

Atdec

Atdec 8060 Manual de usuario

Atdec

Atdec Visidec Focus Articulated Arm Wall Instrucciones de operación

Atdec

Atdec AWMS-2-LTH75-H Manual de usuario

Atdec

Atdec AWMS-2-4640-C Manual de usuario

Atdec

Atdec AWM-WS Manual de usuario

Atdec

Atdec AF-WD Manual de usuario

Atdec

Atdec Visidec Focus Micro Manual de usuario

Atdec

Atdec SD-AT-DW Manual de usuario

Atdec

Atdec AWM-AD Manual de usuario

Atdec

Atdec Telehook Manual de usuario

Atdec

Atdec ADBS-2x2-17MFB Manual de usuario

Atdec

Atdec ADBS-3x1-30TW Manual de usuario

Atdec

Atdec AWM-A13 Manual de usuario

Atdec

Atdec ADB-FS Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario