Atdec AWM-X40 Manual de usuario

AWM-X40 Page 1 of 3

Installation Guide

AWM-X40

AWM Stack Kit 40

COMPONENT CHECKLIST

REQUIRED TOOLS

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! This product is only compatible with Atdec AWM Post 40 Stackable (AWM-P40X).

! Both posts must be AWM-P40X when using this kit.

! The manufacturer accepts no responsibility for incorrect installation.

• 10mm (3/8”) Wrench

• 8mm (5/16”) Wrench

(unstacking only)

M6 Threaded Rod

with M8 Tips

(x2)

M6 Washer

Plate

(x1)

M6 Split

Washer

(x2)

M6 Nut

(x2)

AWM-X40 Page 2 of 3

remove label

but ensure

alignment

insert stays

in place.

Alignment

insert

Ensure channels

without guide

marks are aligned

on both posts.

Alignment

insert

Alignment

insert

If alignment insert falls out,

reposition it as shown above.

Ensure arrow on alignment

insert points away from the

post channel without guide

marks on both posts.

1. Screw Threaded Rods into Post

2. Stack Post

1.1 Remove post cap and label on both posts.

NOTE

Rods can be

nger tightened

2.1 Align the second post with

its alignment insert facing the

tips of the rods. Then feed the

threaded rod into the holes of

the second post.

2.2 Slide the post down the rods until it sits

ush against the top of the lower post.

1.2 Screw threaded rods into the end of one

post that has the alignment insert.

IMPORTANT Check Desk Fixing (xing sold separately)

AWM-FH AC-GC

Atdec Custom

Rail Plate

When stacking posts only the following

heavy duty xings can be used:

1.1 If lower post is already installed, the

xing on the lower post may need to be

changed. Follow the installation guide

provided with your heavy duty xing

to attach it to the post and t it to the

worksurface.

NOTE:

Posts can be stacked

before or after attaching

to desk xing.

STACKING INSTRUCTIONS

AWM-X40 Page 3 of 3

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Remove two

threaded rods

using an 8mm

(5/16”) wrench.

If tips come off the

end of the rods

screw them back

together before

storing for later use.

Unscrew two nuts

using 10mm (3/8”)

wrench.

Ensure the two

alignment inserts

stay in the ends

of both posts.

1. Remove Stacked Post

2. Remove Threaded rods

UNSTACKING INSTRUCTIONS

1.1 Remove cap and all monitor

arms from the stacked post.

2.1 Unscrew two threaded rods using

an 8mm (5/16”) wrench.

1.2 Remove nuts and washers

from top of post.

2.2 Fit post cap

1.3 Slide stacked post up off the

threaded rods.

2.3 Store parts together for later use.

Tighten two nuts

ﬁrmly using 10mm

(3/8”) wrench.

Ensure the post join area

remains well aligned

while tightening the nuts.

3. Fasten Posts Together

3.1 Screw together the posts using

the provided nuts and washers.

3.2 Fit post cap

Follow post and

arm installation

guides to complete

installation of your

mounting solution.

Installation Complete

Otros manuales de Rack y soporte de Atdec

Atdec

Atdec TH-PFK Manual de usuario

Atdec

Atdec Visidec Focus Micro Instrucciones de operación

Atdec

Atdec AWM-W6 Manual de usuario

Atdec

Atdec ADBS-2x2-17MFB Manual de usuario

Atdec

Atdec AWMS-2-D13-C Manual de usuario

Atdec

Atdec ADBS-4x1-39TW Hoja de instrucciones

Atdec

Atdec VFS-DV Manual de usuario

Atdec

Atdec VF-AT-NP Manual de usuario

Atdec

Atdec AWMS-3-137140-C Manual de usuario

Atdec

Atdec AF Series Manual de usuario

Atdec

Atdec AD-TVAC-CM Manual de usuario

Atdec

Atdec AWM-A13 Manual de usuario

Atdec

Atdec TH-1040-CTS Manual de usuario

Atdec

Atdec Freestanding Quad Manual de usuario

Atdec

Atdec AWM-WS Manual de usuario

Atdec

Atdec AWM-LC Manual de usuario

Atdec

Atdec AWM-W6 Manual de usuario

Atdec

Atdec AWM-A13 Manual de usuario

Atdec

Atdec APA-B Manual de usuario

Atdec

Atdec Levitate Instrucciones de operación

Atdec

Atdec 8060 Manual de usuario

Atdec

Atdec AWMS-BT40 Manual de usuario

Atdec

Atdec SPACEDEC ACROBAT Instrucciones de operación

Atdec

Atdec VFS-DH Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario