Assa Abloy Corbin Russwin HPSK Manual de usuario
For installation assistance contact Corbin Russwin
Installation Instructions
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Push/Pull (HPSK) Paddle Trim for
ML2000 Series Mortise Locks
1Mortise Lock Handing Instructions.............................................2
Mortise Lock Door Preparation & Installation .....................................3
HPSK Trim Installation.....................................................5
Turn-Piece Installation.....................................................8
Coin-Turn Installation .....................................................8
3
2
5
4
TOC Table of Contents
Cover Screws
Cover
Paddle
Insert Insert
Screws
Surface Mount
Screws
Axle
Mounting
Post Screws
Inside Paddle
Chassis
Axle
Outside Paddle
Chassis
Surface Mount
Screws
Insert
Screws
Insert
Paddle
CoverCover Screws
Mounting
Posts
WARNING
This product can expose
you to lead which is
known to the state of
California to cause cancer
and birth defects or other
reproductive harm. For
more information go to
www.P65warnings.ca.gov.
08/2018
For installation assistance contact Corbin Russwin
2
FM339 10/18
Push/Pull (HPSK) Paddle Trim
Installation Instructions
ML2000 Series Mortise Lock
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
MAKE SURE CATCH PLATE IS
EVEN W/ TOP SURFACE
GOOD BAD
WARNING:
LOCK-IN CAN
OCCUR IF LATCH
IS NOTPROPERLY
INSTALLED
4. Push in latch while holding
screwdriver behind latch tail.
(Figure 3)
5. Rotate lock front to match bevel of door as
shown. (Figure 5)
1Mortise Lock Handing Instructions
Figure 1
Figure 2
Figure 3
RED Locking Screw
Catch Plate
LOCK HANDING
IS CRITICAL TO
ENSURE LOCK
FUNCTIONS
PROPERLY
Figure 4
1. Move the Red locking screw to side of lockbody
being locked.
2. Push in latch then depress catch plate with
screwdriver. (Figure 1)
3. Pull latch out of lock-body and turn latch over.
(Figure 2)
Figure 5
NOTE:
PUSH IN LATCH UNTIL CATCH
PLATE IS NO LONGER DEPRESSED.
(FIGURE 4)
For installation assistance contact Corbin Russwin
3
FM339 10/18
Push/Pull (HPSK) Paddle Trim
ML2000 Series Mortise Lock
Installation Instructions
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Turn-Piece Door
Marker Template
Inside
of Door
Turn-Piece Door
Marker Template
Outside
of Door
2 Mortise Lock Door Preparation & Installation
Figure 6
Important: Be sure to hand the lockbody
before installing. See Section 1.
1. Insert mortise lock into door and fully
tighten 1" lock mounting combination
screws. (Figure 6)
2. TURN-PIECE FUNCTIONS ONLY:
Insert turn-piece door marker spindle into
lockbody on inside of door.
3. TURN-PIECE FUNCTIONS ONLY:
Slide turn-piece door marker over spindle.
4. TURN-PIECE FUNCTIONS ONLY:
Mark three holes for turn-piece. (Figure 8)
5. COIN-TURN FUNCTIONS ONLY:
Insert turn-piece marker spindle into
lockbody on outside of door.
6. COIN-TURN FUNCTIONS ONLY:
Slide turn-piece door marker template over
spindle.
7. COIN-TURN FUNCTIONS ONLY:
Mark two holes for coin-turn. (Figure 9)
NOTE:
USE SQUARE SIDE OF DOOR MARKER SPINDLE.
(FIGURE 7)
NOTE:
USE SQUARE SIDE OF DOOR MARKER SPINDLE.
(FIGURE 7)
Figure 7
Figure 8
Square
Side
Figure 9
For installation assistance contact Corbin Russwin
4
FM339 10/18
Push/Pull (HPSK) Paddle Trim
Installation Instructions
ML2000 Series Mortise Lock
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Ø.290" Ø3/8"
Ø3/8"
Ø1/8" Ø1/8"
Figure 10
8. Remove lockbody from door.
9. TURN-PIECE FUNCTIONS ONLY:
Drill one middle hole (.290") and two outer holes
(3/8") halfway through door. (Figure 10)
10. COIN-TURN FUNCTIONS ONLY:
Drill two holes (1/8") halfway through door.
(Figure 11)
11. TURN-PIECE FUNCTIONS ONLY:
Install turn-piece thru-bolt plate using truss
head screw. (Leave screw slightly loose.)
(Figure 12)
12. Insert mortise lockbody into door and loosely
tighten 1" lock mounting combination screws.
NOTE:
MAKE SURE LOCK IS UNLOCKED. (FIGURE 13)
Figure 11
MAKE SURE LOCK
IS UNLOCKED
Un-Locked
Locked
Narrower Hole
Wider Hole
Strike Lip
* Strikes for Non-Deadbolt functions
only have narrower hole.
Figure 13
Figure 12
NOTE:
THE THRU-BOLT PLATE IS INSTALLED INSIDE
THE DOOR POCKET.
2Mortise Lock Door Preparation & Installation
Thru-bolt
Plate
For installation assistance contact Corbin Russwin
5
FM339 10/18
Push/Pull (HPSK) Paddle Trim
ML2000 Series Mortise Lock
Installation Instructions
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Cylinder
Set Screw
Narrower Hole
Wider Hole
Strike Lip
3HPSK Trim Installation
Figure 14
Figure 15
1. Install strike using 3/4" strike mounting screws.
2. CYLINDER FUNCTIONS ONLY:
Slide cylinder(s) through spring and collar,
threading into lockbody until cylinder face is
flush with collar. (Figure 15)
3. CYLINDER FUNCTIONS ONLY:
Install cylinder set screw(s). (Figure 17)
4. Fully tighten lock mounting screws.
5. Align cam and chassis as shown based on
desired paddle orientation. (Figure 18)
NOTE:
STRIKE MUST BE ORIENTED WITH
NARROWER HOLE ON LOWER HALF OF
STRIKE AND STRIKE LIP TOWARDS PULL
SIDE OF DOOR. (FIGURE 14)
NOTE:
PULL KEY SLIGHTLY OUT OF CYLINDER TO HELP
THREAD INTO LOCKBODY.
NOTE:
CYLINDER MUST BE ORIENTED CORRECTLY.
(FIGURE 16)
NOTE: Key and
cylinder must be
rotated as shown
Correct Incorrect
®
ASSA ABLO Y
®
ASSA ABLOY
Figure 16
Figure 17
Vertical Paddle
CAM
Vertical
Paddle UP
Vertical
Paddle DOWN
Horizontal Paddle
Mounting Post Location
=OR
=
Mounting Post Location
Mounting Post
Location
CAM
Figure 18
For installation assistance contact Corbin Russwin
6
FM339 10/18
Push/Pull (HPSK) Paddle Trim
Installation Instructions
ML2000 Series Mortise Lock
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
CAM
Spindle NOT Engaged
Spindle Engaged
OUTSIDE INSIDE
Mounting
Posts
Mounting
Screws
3HPSK Trim Installation
6. Insert mounting posts through outside
chassis then install trim on both sides of
door using mounting screws (loosely tighten
mounting screws). Make sure spindle is fully
engaged in lockbody. (Figure 19)
Figure 19
Figure 20
Figure 21
7. Fully tighten 1" lock mounting combination
screws then level out chassis using a
square. (Figure 20)
8. Fully tighten mounting post screws.
9. Rotate cam by hand to make sure trim is not
binding - latch must project freely when cam
is released. If trim binds loosen mounting
screws and re-align trim. (Figure 21)
10. Install surface mount screws. (Figure 22)
For Wood Door:
- Drill two (2) 7/64" holes for surface mount
screws
- Install surface mount wood screws
For Metal Door:
- Drill and tap door for #8-32 screws
- Install surface mount machine screws
NOTE:
USE SQUARE TO LEVEL OUT CHASSIS
Figure 22
Surface Mount
Screw Holes
For installation assistance contact Corbin Russwin
7
FM339 10/18
Push/Pull (HPSK) Paddle Trim
ML2000 Series Mortise Lock
Installation Instructions
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Figure 20
Figure 22
3HPSK Trim Installation
11. Install insert on paddle based on desired paddle
orientation. (Figure 23)
Figure 26
Figure 24
CAUTION:
- SCREWS MUST BE POSITIONED BEHIND
PADDLE TO WORK PROPERLY
- Cover will be very difficult to remove if
forced on backwards Figure 25
12. Attach paddle to chassis by aligning paddle
as shown then insert axle through pivot hole
in chassis. (Figure 24)
13. Install cover using 5/16" oval head mounting
screws. (Figure 25)
14. Install scalp using 3/16" Flat Head Screws.
(Figure 26)
Vertical Paddle UP Vertical Paddle DOWN
Horizontal Paddle
==
OR
Paddle Insert Paddle Insert
Figure 23
NOTE:
COVER HOOKS UNDERNEATH CHASSIS
ON SIDE OPPOSITE MOUNTING SCREWS SCALP
For installation assistance contact Corbin Russwin
FM339 10/18
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Patent pending and/or patent: www.assaabloydss.com/patents
Corbin Russwin
225 Episcopal Road
Berlin, CT 06037
Phone: 800-543-3658
Fax: 800-447-6714
corbinrusswin.com
4 Turn-Piece Installation
1. Install turn-piece loosely using two (2) turn-
piece mounting screws. (Figure 27)
2. Adjust location of turn-piece on door until
turn-piece rotates easily, then fully tighten
mounting screws.
Figure 28
Figure 29
NOTE:
MAKE SURE LOCK IS UNLOCKED AND
TURN-PIECE IS ROTATED TOWARDS
LATCH. (FIGURE 28)
MAKE SURE LOCK
IS UNLOCKED
Un-Locked
Locked
Narrower Hole
Wider Hole
Strike Lip
* Strikes for Non-Deadbolt functions
only have narrower hole.
5 Coin-Turn Installation
Figure 27
1. Install coin-turn using two surface mount
screws. (Figure 29)
Tabla de contenidos
Otros manuales de Cerrar de Assa Abloy
Assa Abloy
Assa Abloy Cabinet Lock Series Manual de usuario
Assa Abloy
Assa Abloy Sargent PASSPORT 1000 P1 Manual de usuario
Assa Abloy
Assa Abloy Sargent IN100 Manual de usuario
Assa Abloy
Assa Abloy Assa compact 3000 Series Manual de usuario
Assa Abloy
Assa Abloy Yale Real Living Assure Lock YRD226 Especificaciones técnicas
Assa Abloy
Assa Abloy APERIO E100 Scand Manual de usuario
Assa Abloy
Assa Abloy Securitron CEPT-10-10 Manual de usuario
Assa Abloy
Assa Abloy Sargent Profile v.S1 Manual de usuario
Assa Abloy
Assa Abloy Yale Doorman Manual de usuario
Assa Abloy
Assa Abloy Securitron SAM Manual de usuario
Assa Abloy
Assa Abloy EMTEK EMTouch Classic Style Instrucciones de funcionamiento
Assa Abloy
Assa Abloy HES KS200-640 Manual de usuario
Assa Abloy
Assa Abloy Yale Real Living Assure Lock SL Series Especificaciones técnicas
Assa Abloy
Assa Abloy Securitron Shear Aligning Magnalock SAM... Manual de usuario
Assa Abloy
Assa Abloy ML53PA Manual de usuario
Assa Abloy
Assa Abloy Sargent 8200 Series Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin FE6800 Series Manual de usuario
Assa Abloy
Assa Abloy Sargent KP Series Manual de instalación
Assa Abloy
Assa Abloy effeff 9338 Guía
Assa Abloy
Assa Abloy Door Lock Manual de usuario
