Assa Abloy EMTEK EMTouch Classic Style Instrucciones de funcionamiento
ASSA ABLOY, the global leader in door opening solutions
Installation & Programming Guide
EMTouch™ & EMTouch™ Classic Style
Electronic Deadbolt Locksets
EMTouch™
EMTouch™ Classic Style
2
4c
4d
2
3
ITEM NO. DESCRIPTION QTY.
1Key 2
2Outside Trim Plate Assembly 1
3Deadbolt Latch Assembly 2 3/8”or 2 ¾” Backset 1
4Inside Trim Plate Assembly 1
4a Inside Chassis
1
4b Inside Trim Plate
1
4c
#8-32 x 3/8” Flat Head Machine Screw 2
4d
9V Alkaline Battery 1
5#8-32 x 1½” Flat Head Machine Screw 2
6#8 x ¾”Wood Screw 4
7Strike Plate 1
8Security Plate 1
9#10 x 3”Wood Screw 2
6
5
1
6
8
9
7
4
4b
4a
What’s in the Box
3
2-3/8” or 2-3/4” Backset
2 1/8” Diameter Bore
1/8” Deep
2 ¼”
1 “ 1” Diameter Edge Bore
2. Door Jamb Prep
1. Door Prep
Preparation
Step 1: Fasten Security Plate using two #10 x 3”Wood Screws (item #9).
Step 2: Fasten Strike Plate using two #8 x ¾”Wood Screws (item #6).
2-3/4"
#10 x 3”Wood Screws
3/16” Deep
2 ¾”
11/8”
¾”
#8 x ¾”Wood Screws
1¼”
1¼” Deep
4
Scan
this QR
code for
details.
Fasten Latch using two #8 x ¾”Wood Screws (item #6).
2. Remove Screws from Inside Trim Plate
1. Install Latch
How to Install
!
REMOVE INSIDE CHASSIS
FROM TRIM PLATE BEFORE
INSTALLING THE OUTSIDE
TRIM. THUMBTURN MUST
BE IN UNLOCKED POSITION.
Unlocked Locked
THE LATCH ASSEMBLY
MUST BE ORIENTED
AS SHOWN AND THE
BOLT MUST BE IN THE
RETRACTED POSITION
FOR INSTALLATION.
!
Crosshairs
at bottom.
Use a Phillips head screwdriver to remove screws (item #4c) shown below and
detach Inside Trim Plate from the Inside Chassis.
screws
(item #4c)
5
3. Install Outside Trim Plate Assembly
4. Install Inside Chassis
Position the Outside Trim Plate Assembly through the bore hole.
!
Fit Flat Shaft
through latch.
Flat Shaft must be
in vertical position
for installation.
ONCE POSITIONED,
OUTSIDE TRIM PLATE
ASSEMBLY REQUIRES
SUPPORT.
Feed wire harness
through the bore hole.
HOLE FOR FLAT
SHAFT MUST BE IN
VERTICAL POSITION
FOR INSTALLATION.
!
Step 1: Confirm the position of Flat Shaft.
√ Correct for Installation.
X Incorrect for Installation.
Scan
this QR
code for
details.
6
4. Install Inside Chassis
Step 2: Feed the Wire Harness through Inside Chassis.
Step 3: Fasten Inside Chassis using two #8-32 x 1½”Flat Head Machine Screws (item #5).
CHECK ALIGNMENT BEFORE
FULLY TIGHTENING SCREWS.
!
7
Step 4: Connect Wire Harness (A) and tuck Connectors as shown (B).
A
B
Step 5: Install Battery.
For optimal performance, always use a good quality battery.
9V Battery
Scan
this QR
code for
details.
8
*Unlocked position is required for installation and removal of the Inside
Trim Plate Assembly.
*Unlocked
Correct for installation
Locked
Screws (item #4c)
Incorrect for installation
!
!
THUMBTURN MUST BE IN
UNLOCKED POSITION FOR
INSTALLATION.
USER CODES
ARE LOCATED
ON THE INSIDE
TRIM PLATE &
ON PAGE 11.
Inside
5. Install Inside Trim Plate
Fasten Inside Trim Plate using two #8-32 x 3/8” Flat Head Machine Screws
(item #4c).
9
Your Emtek lock is shipped with two 4-digit user codes and a 6-digit
programming code. These codes are randomly generated at the factory.
(Turn to next page for Programming Instructions.)
To Unlock:
To Lock:
Option 1
1. Press EMTEK key.
2. Rotate Thumbturn.
Option 2
1. Touch 3 ngers across screen.
2. Enter 4-digit user codes.
(See sticker located on the inside
trim plate or on page 11).
3. Rotate Thumbturn.
Your Lock is Ready to Use
How to Use
3
2
2
1
1
1. Press EMTEK key or touch
3 ngers across screen.
2. Enter 4-digit user codes.
(See sticker located on the inside
trim plate or on page 11).
3. Rotate Thumbturn.
10
How to Program
Programming Your Lock
In order to perform each of the following six functions, the lock must rst be
placed in Programming Mode:
*If no input within 20 seconds, Yellow LED goes out, Red LED ashes and lock exits Programming Mode.
1. Press and hold EMTEK button for 3 seconds
2. Yellow LED ashes, then remains solid*, number keys also illuminate
3. Enter Programming Code
4. Yellow LED ashes, then 1 beep
5. Yellow LED remains solid (awaiting button press; see following Table)
Ifyou wIsh to Press
Button
ActIons IndIcAtors
Change
Programming
Code
(6 digits)
1Enter New
Programming
Code
(6 digits)
Re-Enter
New
Programming
Code
(6 digits)
• 1 Green LED ash
• 1 beep
• 1 Green LED ash
• 1 beep
• 2 Green LED ashes
• 2 beeps
Add User Code
(4 digits)
(Store up to 20
User Codes)
2Enter New
User Code
(4 digits)
Re-Enter
New User
Code
(4 digits)
• 1 Green LED ash
• 1 beep
• 1 Green LED ash
• 1 beep
• 2 Green LED ashes
• 2 beeps
Delete User Code 3Enter User
Code to be
Deleted
Re-Enter
User Code to
be Deleted
• 1 Green LED ash
• 1 beep
• 1 Green LED ash
• 1 beep
• 2 Green LED ashes
• 2 beeps
**Enable/Disable
All User Codes
4Entering ‘4’ disables all Users
(enables all if disabled)
• 2 Green LED ashes
• 2 beeps
Delete All User
Codes
5Re-Enter Programming Code • 1 Green LED ash
• 1 beep
• 2 Green LED ashes
• 2 beeps
Turn Beeper On/
Off
6Entering ‘6’ turns OFF (or ON) • 1 Green LED ash
• 1 beep
• 2 Green LED ashes
• 2 beeps
**Also referred to as “vacation mode”. This command temporarily disables all user codes (metal key
override will still work).
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cerrar de Assa Abloy
Assa Abloy
Assa Abloy Bolt ASSA 560/13 Manual de usuario
Assa Abloy
Assa Abloy Sargent 9700 Manual de instrucciones
Assa Abloy
Assa Abloy Sargent 6500 Manual de instrucciones
Assa Abloy
Assa Abloy Sargent KP Series Manual de instalación
Assa Abloy
Assa Abloy 840C-50 Manual de usuario
Assa Abloy
Assa Abloy Sargent 8200 Manual de usuario
Assa Abloy
Assa Abloy ELECTRIC LOCK Manual de usuario
Assa Abloy
Assa Abloy Yale 7370 Series Manual de usuario
Assa Abloy
Assa Abloy OneSystem 819N Guía de instalación
Assa Abloy
Assa Abloy Yale YM Series Manual de usuario
Assa Abloy
Assa Abloy IKON eCLIQ N111 BA3 Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin IN120 Manual de usuario
Assa Abloy
Assa Abloy 421-30-10 Manual de usuario
Assa Abloy
Assa Abloy 3090 Guía
Assa Abloy
Assa Abloy Adams Rite DL100 Manual de usuario
Assa Abloy
Assa Abloy Aperio Series Manual de usuario
Assa Abloy
Assa Abloy 8037...UL-91E91 Series Manual de usuario
Assa Abloy
Assa Abloy Sargent Passport 1000 Series Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin IN220 PoE Manual de usuario
Assa Abloy
Assa Abloy OneSystem 309N Manual de usuario
