Assa Abloy Cabinet Lock Series Manual de usuario

1 Part Number 3085006.001, Rev 3

HES K200-622

Cabinet Lock Series

Installation Instructions

Machine

screw with

washer

Package Contents

Strike Plate

6-32 screws

5/16”

1”

1-5/8”

1-1/4”

1-3/4”

2-1/2”

Shaft Extension

0-80x½”

2-56x3/8”

2-56x1-1/4”

Key Override Paddle

6 x 1/2”

1-7/8”

Recommended Tools

Optional:

Cam lock for key override

Double door bracket

Lock Body

Drill, Drill bits: 5/32”, 1/2”

Approved Credential:

i.e. iCLASS or Prox ID card

Phillips drivers P0, P2

Pencil, Wire Stripper

Voltage: 12–24 VDC ±10% (Power Supply not provided)

HES K200-622 (Reader) Current Consumption:

12 VDC: 38 mA peak for Red and Green LED only

226 mA peak for Red and Green LED and Motor Drive

24 VDC: 17 mA peak for Red and Green LED only

118 mA peak for Red and Green LED and Motor Drive

Operating Temperature: -10C to 50C

Holding Force: 150 lbs

Lock Reader

Specifications

Mounting

Template

Interface Cable, Lock Side

Interface Cable,

System Side

Cam

2 Part Number 3085006.001, Rev 3

Connector Pin Wiring:

Molex 8-Pin Connector Pin

Wire Color

Description

Black

12 VDC Reader (–)

White

Wiegand Data (1)

N/A

Red

12 VDC Reader (+)

Green

Wiegand Data (0)

Blue

Red LED

Yellow

Green LED

Molex 4-Pin Connector Pin

Violet

12/24 VDC / Lock (COM, –)

Pink

Tamper / DPS (NC, +)

Gray

12/24 VDC / Lock (COM, +)

Tan

Tamper / DPS (COMM, –)

LED Function: LED states are controlled and defined by the User’s EAC. Enabling the red and green LEDs on

the HES K200 occurs via an active low (ground) signal.

Output Type: SIAAC-01-1996 Wiegand Output Compliant.

FCC Part 15, Compliant, Industry Canada Compliant

BHMA: A156.3, A156.36, A156.25 Compliant

NOTE: Contact HID Global Technical Support at (866) 607-7339 for additional configuration cards to enable

the credential capabilities of “iCLASS Elite”and “NFC over HCE.”

Credentials Supported: 125 kHz Proximity or 13.56 MHz iCLASS, iCLASS Elite, iCLASS SEOS, iCLASS SE, ISO

15693 ICLASS, ISO 14443A Mifare, Mifare Plus, Desfire SE, Desfire EV1, and NFC over HCE.

SYSTEM OVERVIEW

The HES K200-622 wired cabinet lock (K200) extends access control to a cabinet or drawer. The HES K200

lock is capable of reading radio-frequency identification (RFID) credentials and providing that credential data

to an electronic access control (EAC) system via Wiegand data signaling. The EAC is responsible for

determining whether user access should be granted or denied. When the EAC provides an active-high unlock

signal to the lock in the access granted case, the HES K200 drives a motor to complete the unlock/lock cycle.

EAC indication of user access/denial is provided to the user by way of LED control inputs on each lock.

Additional lock monitoring features (e.g., door position, tamper) are monitored within the lock and status of

each is provided to the EAC.

3 Part Number 3085006.001, Rev 3

MOUNTING THE LOCK

NOTE: The HES K200 reader and lock body can be oriented in several ways to accommodate various cabinets and

drawers. When selecting an orientation, it should be noted that some reader orientations may prevent use

of the key override function. For example, in the door handing shown here, the key override paddle cannot

be accessed in orientation “A”, but it can be accessed in orientations “B,” “C” and “D”.

1. ESTABLISH the horizontal centerline of the latch.

a. HOLD the lock body to the inside of the door and POSITION it generally where you would like it to mount.

b. LOCATE lock centerline notch on the latch, and MARK this point on the inside of the cabinet door using a

pencil.

c. DRAW the horizontal latch centerline from this mark on the inside of the cabinet door and TRANSFER it to the

outside of the cabinet door.

d. TRANSFER this centerline to the inside of the cabinet or the second door on a double-door cabinet.

1b + 1c

4 Part Number 3085006.001, Rev 3

2. TRANSFER the location of the inside wall of the cabinet to the door.

a. MEASURE the horizontal distance between the inside edge of the cabinet and the door edge.

NOTE: The drawn line depicts the location of the strike mounting surface.

b. LOCATE the lock centerline notch on the latch and MARK this point on the inside of the cabinet door using a

pencil.

c. DRAW the horizontal latch centerline from this mark on the inside of the cabinet door and TRANSFER it to the

outside of the cabinet door.

3. PLACE and USE the Lock/Reader Template.

NOTE: The orientation will be reversed for a right hand door.

a. CUT through line to separate the Strike Plate Template.

b. PEEL OFF the protective layer of the Lock Template, ALIGN it to both the latch centerline and the line

depicting the inside wall of cabinet, and PRESS to secure.

NOTE: Two of the holes in the following step are 3/16” [4.76 mm] diameter and two are 1/2” [12.70 mm]

diameter. The two pilot holes are 1/16” [1.59 mm].

c. DRILL four holes and two pilot holes through the cabinet, as shown in the figure below.

d. DRILL only one 3/16” [4.76 mm] hole, depending on the desired Antenna/Reader orientation.

e. IF the optional key override will be installed,

THEN GO TO Step 5.

f. REMOVE the lock template from the door.

5 Part Number 3085006.001, Rev 3

4. INSTALL the shaft extension.

IF the cabinet door thickness is greater than 1/2” [12.70 mm] (see Table 1),

THEN INSTALL the Shaft Extension to the Antenna/Reader as shown below to ensure proper engagement

into the lock. Firmly tighten the screw.

Table 1

Door Thickness

Extension Shaft Used?

1/16” [1.59 mm] – 1/2” [12.70 mm]

> 1/2” [12.70 mm] – 1-1/2” [38.10 mm]

Yes

5. IF a Cam Lock key override will be used,

AND the orientation allows for installation,

THEN INSTALL the Key Override Paddle.

a. INSERT the paddle’s arm into the opening shown, and ALIGN the rails of the paddle to the ones on the lock.

b. SLIDE the paddle gently until it stops.

6. PREPARE the Key Override Door.

NOTE: The Cam Lock is optional and is not included with the HES K200.

a. IF a Key Override is used,

THEN MARK and DRILL a hole for a 3/4” [19.05 mm] Cam Lock in the door using the template as a guide.

b. INSTALL the optional Cam Lock with the Cabinet Lock as shown in the figure.

6 Part Number 3085006.001, Rev 3

7. INSTALL the Antenna/Reader.

CAUTION

Pinching the wires may prevent the Reader and Lock from properly functioning.

a. PLACE and HOLD the antenna/reader to the outside of cabinet, routing the wire through the 1/2” [12.70 mm]

offset hole, and ENSURE the knob is in the vertical, locked position.

NOTE: Use Table 2 to determine the length of the top mount screw needed, based on the thickness of the

cabinet door.

b. INSTALL the top mount screw to attach the antenna/reader to the outside case.

Table 2

8. INSTALL the lock body.

a. REMOVE the cover from lock body.

b. PLACE the lock on the inside of the door, threading the cable through the lock.

c. ATTACH the lock to the antenna/reader using two 8-32 [4.00 mm] lock mount screws (see Table 2 for length),

and TIGHTEN the screws.

d. INSTALL the two #6 [3.5 mm] self-threading screws, and TIGHTEN.

NOTE: The third #6 [3.5 mm] self-threading screw is important to achieve maximum holding force for doors

greater than 5/8” [15.88 mm] thick.

e. INSTALL the third #6 [3.5 mm] self-threading screw only if the door is greater than 5/8” [15.88 mm] thick,

using the lock as a guide, and TIGHTEN.

7 Part Number 3085006.001, Rev 3

9. CONNECT the antenna/reader wire to the lock body.

NOTE: The antenna/reader wire connector is engineered to fit only one way.

a. INSERT the antenna/reader wire connector, ensuring correct orientation

b. TUCK excess cable into the lock body.

c. ATTACH the cover.

Connector cable tucked in 9b

8 Part Number 3085006.001, Rev 3

10. Attaching the Wiring

New 4-/8-Pin Molex

Integrated Wiegand: K/KS200 Cabinet Locks, ElectroLynx Wire Color/Function Assignments

Connecto

8-Pin Molex Connector

4-Pin Molex Connector

Pin/Wire

Color

Black

White

N/A

Red

Green

Blue

Yellow

Violet

Pink

Gray

Tan

Function

12 VDC

Reader

Wiegand

Data

N/A

12 VDC

Reader

Wiegand

Data

LED

12/24

VDC/

Lock

Tamper

/ DPS

12/24

VDC/

Lock

Tamper

/ DPS

Setting

NEG

Data 1

N/A

POS

Data 0

RED

Green

COM, -

NC, +

COM, +

COM, -

Legacy 10-Pin Molex to 4-/8-Pin Molex

Integrated Wiegand: K/KS200 Cabinet Locks, ElectroLynx Wire Color/Function Assignments

Connector

8-Pin Molex Connector

4-Pin Molex Connector

Pin/Wire

Color

Black

White

N/A

Red

Green

Orange

Brown

Gray

Yellow

Violet

Blue

Function

12 VDC

Reader

Wiegand

Data

N/A

12 VDC

Reader

Wiegand

Data

LED

12/24

VDC/

Lock

Tamper/

DPS

12/24

VDC/

Lock

Tamper/

DPS

Setting

NEG

Data 1

N/A

POS

Data 0

RED

Green

COM, -

NC, +

COM, +

COM, -

a. CONNECT the Lock Side Interface Cable to the lock.

b. CONNECT the Lock Side Interface Cable to the optional System Side Interface Cable (see Connector and Cable Diagram).

c. RUN the System Side Interface Cable, as required.

d. ATTACH the included 4-Pin and 8-Pin Molex Female Connectors to the bare wire side of the System Side Interface Cable.

Locke side

Interface Cable

(Optional accessory)

CBL 6-QC12- lock side interface cable 6ft

CBL 12-QC12- system side interface cable 12ft

9 Part Number 3085006.001, Rev 3

NOTE: It is recommended that 10-conductor, 24 AWG, cable be used.

11. ENSURE the following power cabling guidelines are followed:

Wire AWG

Supply Voltage

Allowed Cable Length (ft.)*

20 AWG

872

6679

22 AWG

548

4201

24 AWG

345

2641

* Round trip loss. V = 2 x I x R x xft xft = V / (2 x I x R)

12. POSITION the cable out of the way, as required.

13. PREPARE for the single door strike plate. (If installing on a double door, skip to Step 15)

a. PEEL OFF the protective layer of the Strike Plate Template and ALIGN it to both the latch centerline and the

cabinet edge.

b. DRILL the two pilot holes shown on the template.

c. REMOVE the template.

CAUTION

The Installer must ensure that the lock can be opened before closing the cabinet door.

14. INSTALL the single door strike plate.

a. PLACE the strike plate over the pilot holes, and INSERT and TIGHTEN the two screws in the slotted

holes.

b. CLOSE the door to verify installation, and ADJUST the strike plate if necessary.

c. INSERT and TIGHTEN the lock down screw on the strike plate.

10 Part Number 3085006.001, Rev 3

15. INSTALL for the double-door strike plate mounting bracket. (OPTIONAL)

NOTE: The double-door strike plate bracket requires that one door can be inactive or secured.

a. PLACE the bracket on door, making sure it aligns with the mark made in Step 2c and the edge of the door.

b. MARK the door.

c. REMOVE the bracket and DRILL pilot holes at the two marks.

d. INSTALL the bracket using the provided mounting screws.

16. INSTALL the double-door strike plate.

a. PLACE the strike plate over the holes on the bracket.

b. INSERT and TIGHTEN the three 6-32 x 5/16” (3.5 mm x 7.94 mm) provided screws.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

IC Statement

This device complies with Industry Canada license-exempt RSS standards(s). Operation is subject to the following

two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation.

15a and 15b 15c and 15d

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerrar de Assa Abloy

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Manual de usuario

Assa Abloy

Assa Abloy Sargent Passport 1000 Series Manual de usuario

Assa Abloy

Assa Abloy hes 8000 Series Manual de usuario

Assa Abloy

Assa Abloy Yale Real Living Assure Lock SL YRD256 Especificaciones técnicas

Assa Abloy

Assa Abloy KESO KEK i-handle S Guía del usuario

Assa Abloy

Assa Abloy SECURITRON MORTISE UNLATCH MUNL-12 Manual de usuario

Assa Abloy

Assa Abloy EL595 Manual de usuario

Assa Abloy

Assa Abloy Yale 5300 Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario

Assa Abloy

Assa Abloy INTERLOCK P84166 Manual de usuario

Assa Abloy

Assa Abloy Securitron Shear Aligning Magnalock SAM... Manual de usuario

Assa Abloy

Assa Abloy eCLIQ Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin UT5200 Series Guía de inicio rápido

Assa Abloy

Assa Abloy APERIO P100 Manual

Assa Abloy

Assa Abloy eCLIQ Manual de usuario

Assa Abloy

Assa Abloy HES 5000 Series Manual

Assa Abloy

Assa Abloy Yale Doorman Manual de usuario

Assa Abloy

Assa Abloy Sargent Passport 1000 PG Manual de usuario

Assa Abloy

Assa Abloy OneSystem 819N Guía de instalación

Assa Abloy

Assa Abloy Sargent Signature Series Manual de usuario

Assa Abloy

Assa Abloy Securitron M38 Series Manual de usuario

Assa Abloy

Assa Abloy EMTEK CF Mechanism Manual de usuario

Assa Abloy

Assa Abloy SARGENT Delayed Egress 57-80 Series Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario