Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario
For installation assistance contact Corbin Russwin
QR Codes
To view the QR Code video clips within this document, download a free mobile app and scan the QR Code with your mobile device.
The complete video can be viewed on YouTube at https://youtu.be/I5MLFWODumo
Installation Instructions
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
BHSS Trim for
ML2000 Series Mortise Locks
1Mortise Lock Handing Instructions.............................................2
Mortise Lock Door Preparation & Installation .....................................3
BHSS Trim Installation .....................................................5
Turn-Piece Installation.....................................................8
Coin-Turn Installation .....................................................8
3
2
TOC Table of Contents
4
5
Outside Trim
Inside Trim
#10 Escutcheon
Mounting Screws
#8 Escutcheon
Mounting Screws
Lever Set Screw
Thru-bolt
Holes
#8 Adapter
Mounting Screws
Mounting Posts
Cast-in Posts
Adapter Plate
Ta b
Set Screw
Hole
WARNING
This product can expose
you to lead which is
known to the state of
California to cause cancer
and birth defects or other
reproductive harm. For
more information go to
www.P65warnings.ca.gov.
08/2018
For installation assistance contact Corbin Russwin
1-888-607-5703 • [email protected]
2
FM352 10/18
BHSS Trim
Installation Instructions
ML2000 Series Mortise Lock
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
MAKE SURE CATCH PLATE IS
EVEN W/ TOP SURFACE
GOOD BAD
WARNING:
LOCK-IN CAN
OCCUR IF LATCH
IS NOTPROPERLY
INSTALLED
4. Push in latch while holding
screwdriver behind latch tail.
(Figure 3)
5. Rotate lock front to match bevel of door as
shown. (Figure 5)
1 Mortise Lock Handing Instructions
Figure 1
Figure 2
Figure 3
RED Locking Screw
Catch Plate
LOCK HANDING
IS CRITICAL TO
ENSURE LOCK
FUNCTIONS
PROPERLY
Figure 4
1. Move the Red locking screw to side of lockbody
being locked.
2. Push in latch then depress catch plate with
screwdriver. (Figure 1)
3. Pull latch out of lock-body and turn latch over.
(Figure 2)
Figure 5
NOTE:
PUSH IN LATCH UNTIL CATCH
PLATE IS NO LONGER DEPRESSED.
(FIGURE 4)
For installation assistance contact Corbin Russwin
1-888-607-5703 • [email protected]
3
FM352 10/18
BHSS Trim
ML2000 Series Mortise Lock
Installation Instructions
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Turn-Piece Door
Marker Template
Turn-Piece Door
Marker Template
Outside
of Door
Figure 6
2 Mortise Lock Door Preparation & Installation
NOTE:
MAKE SURE TEMPLATE IS ORIENTED
CORRECTLY. (FIGURE 7)
Important: Be sure to hand the lockbody
before installing. See page 4.
1. Insert mortise lock into door and fully
tighten 1" lock mounting combination
screws. (Figure 6)
2. Insert spindle into outside lockbody hub.
3. Slide trim door marker template over
spindle.
4. Square template to edge of door. (Figure 7)
5. Mark two thru-bolt holes.
6. Repeat steps 2-5 for inside of door.
7. TURN-PIECE FUNCTIONS ONLY:
Insert turn-piece door marker spindle into
lockbody on inside of door.
8. TURN-PIECE FUNCTIONS ONLY:
Slide turn-piece door marker over spindle.
9. TURN-PIECE FUNCTIONS ONLY:
Mark three holes for turn-piece. (Figure 9)
NOTE:
USE SQUARE SIDE OF DOOR MARKER SPINDLE.
(FIGURE 8)
NOTE:
USE SQUARE SIDE OF DOOR MARKER SPINDLE.
(FIGURE 8)
10. COIN-TURN FUNCTIONS ONLY:
Insert turn-piece marker spindle into lockbody
on outside of door.
11. COIN-TURN FUNCTIONS ONLY:
Slide turn-piece door marker template over
spindle.
12. COIN-TURN FUNCTIONS ONLY:
Mark two holes for coin-turn. (Figure 10)
Figure 7
Figure 8
Square
Side
Figure 9
Figure 10
Lock-body
Installation
Inside
of Door
For installation assistance contact Corbin Russwin
1-888-607-5703 • [email protected]
4
FM352 10/18
BHSS Trim
Installation Instructions
ML2000 Series Mortise Lock
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Ø.290" Ø3/8"
Ø3/8"
Ø1/8" Ø1/8"
Thru-bolt
Plate
13. Remove lockbody from door.
14. Drill two thru-bolt holes (9/16") halfway
through one side of door.
15. Drill two thru-bolt holes (9/16") through from
opposite side of door.
16. TURN-PIECE FUNCTIONS ONLY:
Drill one middle hole (.290") and two outer holes
(3/8") halfway through door. (Figure 11)
17. COIN-TURN FUNCTIONS ONLY:
Drill two holes (1/8") halfway through door.
(Figure 12)
18. TURN-PIECE FUNCTIONS ONLY:
Install turn-piece thru-bolt plate using truss
head screw. (Leave screw slightly loose.)
(Figure 13)
19. Insert mortise lockbody into door and loosely
tighten 1" lock mounting combination screws.
NOTE:
DRILL THROUGH BOTH SIDES OF DOOR FOR
BETTER ACCURACY.
NOTE:
MAKE SURE LOCK IS UNLOCKED. (FIGURE 14)
2Mortise Lock Door Preparation & Installation
Figure 11
Figure 12
Figure 13
Drill Thrubolt
Holes
Figure 14
NOTE:
THE THRU-BOLT PLATE IS INSTALLED INSIDE
THE DOOR POCKET.
MAKE SURE LOCK
IS UNLOCKED
Un-Locked
Locked
Narrower Hole
Wider Hole
Strike Lip
* Strikes for Non-Deadbolt functions
only have narrower hole.
For installation assistance contact Corbin Russwin
1-888-607-5703 • [email protected]
5
FM352 10/18
BHSS Trim
ML2000 Series Mortise Lock
Installation Instructions
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Narro
wer Hole
Wider Hole
Strike Lip
Cylinder
Set Screw
Figure 15
Figure 16
BHSS Strike
Installation
Cylinder
Installation
Figure 17
3 BHSS Trim Installation
1. Install strike using 3/4" strike mounting screws.
2. CYLINDER FUNCTIONS ONLY:
Slide cylinder(s) through spring and collar,
threading into lockbody until cylinder face is
flush with collar. (Figure 16)
3. CYLINDER FUNCTIONS ONLY:
Install cylinder set screw(s). (Figure 18)
4. Fully tighten lock mounting screws.
NOTE:
STRIKE MUST BE ORIENTED WITH
NARROWER HOLE ON LOWER HALF OF
STRIKE AND STRIKE LIP TOWARDS PULL
SIDE OF DOOR. (FIGURE 15)
NOTE:
PULL KEY SLIGHTLY OUT OF CYLINDER TO HELP
THREAD INTO LOCKBODY.
NOTE:
CYLINDER MUST BE ORIENTED CORRECTLY.
(FIGURE 17)
NOTE: Key and
cylinder must be
rotated as shown
Correct Incorrect
®
ASSA ABLO Y
®
ASSA ABLOY
Figure 18
For installation assistance contact Corbin Russwin
1-888-607-5703 • [email protected]
6
FM352 10/18
BHSS Trim
Installation Instructions
ML2000 Series Mortise Lock
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
3 BHSS Trim Installation
Spindle & Outside
Trim Assembly
Installation
Adapter Plate
Installation
Outside Trim
Adaptor
Plate
Hub
NOTE:
SPINDLE CAN BE USED TO HELP THREAD HUB
INTO LEVER.
Outside Trim
Mounting
P
osts
5. Thread adapter plate hub into lever and fully
tighten. (Figure 19)
6. Align adapter plate hub with square hole in lever;
keeping hub as tight as possible. (Figure 20)
7. Insert spindle into outside trim assembly.
8. With lever in “up” position, align mounting posts
on adapter plate with holes in lockbody and
install outside trim assembly. (Figure 21)
9. Insert spindle into lockbody on inside of door.
(Figure 22)
NOTE:
AFTER OUTSIDE TRIM IS INSTALLED, ROTATE
LEVER TO MAKE SURE SPINDLE IS ENGAGED IN
LOCK.
Figure 19
Figure 20
Use Correct Spindle Orientation
GOODBAD
Figure 21
Figure 22
For installation assistance contact Corbin Russwin
1-888-607-5703 • [email protected]
7
FM352 10/18
BHSS Trim
ML2000 Series Mortise Lock
Installation Instructions
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Set Scre
w
Hole
Adapter
Plate Ta b
Inside Trim
Mounting
Screws
Inside Le
ver
Set Screw
3 BHSS Trim Installation
Mount Escutcheon
Lock Front
Installation
10. Slide inside adapter plate over spindle and
install using two adapter plate mounting
screws. (Figure 23)
11. With lever in “up” position, install inside trim
assembly.
12. Tighten inside lever set screw. (Figure 24)
13. Install three escutcheon mounting screws
through inside escutcheon. (Figure 24)
14. Install lock front using two front screws.
(Figure 25)
NOTE:
AFTER TRIM IS INSTALLED, ROTATE LEVER TO
MAKE SURE SPINDLE IS ENGAGED IN LOCK.
NOTE:
MAKE SURE ADAPTER PLATE TAB AND SET
SCREW HOLE ARE FACING LOCK FRONT PRIOR
TO INSTALLING SCREWS.
Figure 23
Figure 24
Inside Trim
Assembly
Installation
Figure 25
For installation assistance contact Corbin Russwin
1-888-607-5703 • [email protected]
FM352 10/18
Copyright © 2017 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Patent pending and/or patent: www.assaabloydss.com/patents
Corbin Russwin
225 Episcopal Road
Berlin, CT 06037
Phone: 800-543-3658
Fax: 800-447-6714
corbinrusswin.com
4 Turn-Piece Installation
Turn-Piece
Installation
5 Coin-Turn Installation
1. Install coin-turn using two surface mount
screws. (Figure 28)
1. Install turn-piece loosely using two turn-
piece mounting screws. (Figure 26)
2. Adjust location of turn-piece on door until
turn-piece rotates easily, then fully tighten
mounting screws.
Figure 26
Figure 27
NOTE:
MAKE SURE LOCK IS UNLOCKED AND
TURN-PIECE IS ROTATED TOWARDS
LATCH. (FIGURE 27)
Figure 28
MAKE SURE LOCK
IS UNLOCKED
Un-Locked
Locked
Narrower Hole
Wider Hole
Strike Lip
* Strikes for Non-Deadbolt functions
only have narrower hole.
Otros manuales para Corbin Russwin BLSS ML2000 Series
4
Tabla de contenidos
Otros manuales de Cerrar de Assa Abloy
Assa Abloy
Assa Abloy Corbin Russwin CL3100 Series Manual de usuario
Assa Abloy
Assa Abloy Yale Real Living Real Living YRC246 Especificaciones técnicas
Assa Abloy
Assa Abloy eCLIQ Manual de usuario
Assa Abloy
Assa Abloy Yale 7370 Series Manual de usuario
Assa Abloy
Assa Abloy Securitron CEPT-10-10 Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin FE6800 Series Manual de usuario
Assa Abloy
Assa Abloy effeff 9338 Guía
Assa Abloy
Assa Abloy Securitron GL1 Manual de usuario
Assa Abloy
Assa Abloy Yale inTouch Especificaciones técnicas
Assa Abloy
Assa Abloy TCWI1-M812 Manual de usuario
Assa Abloy
Assa Abloy Yale P117 Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin SE LP10 ML20600 Manual de usuario
Assa Abloy
Assa Abloy Access Control Electric Locking Manual
Assa Abloy
Assa Abloy SECURITRON CEPT-10 Manual de usuario
Assa Abloy
Assa Abloy G-S Manual de instrucciones
Assa Abloy
Assa Abloy KESO KEK i-handle S Guía del usuario
Assa Abloy
Assa Abloy 118F A71 Series Manual de usuario
Assa Abloy
Assa Abloy Yale Real Living Assure Lock YRD226 Especificaciones técnicas
Assa Abloy
Assa Abloy Door Lock Manual de usuario
Assa Abloy
Assa Abloy hes 8000 Series Manual de usuario
