Assa Abloy Hes 8000 Series Manual de usuario

8000/8300 Series Electric Strike

Installation Instructions

HES, Inc.

22630 N. 17th Ave.

Phoenix, AZ 85027

800-626-7590

www.hesinnovations.com

Product Components

Diagram 1: Electrical Specifications

ELECTRICAL RATINGS FOR SOLENOID MINIMUM WIRE GAUGE REQUIREMENTS SOLENOID VOLTAGE

CONTINUOUS DUTY

12VDC 12VDC

.24

24VDC 24VDC

200 50 200

.12 .12

12-16VAC 24VAC

INTERMITTENT DUTY*

Resistance in Ohms

Amps

Solenoids are rated at +/- 10% indicated value.

*10% max duty cycle (2 min. max on time)

200 feet or less

200 - 300 feet

300 - 400 feet

18 gauge

16 gauge

14 gauge

20 gauge

18 gauge

16 gauge

12 & 24 Volt Pigtails

8000/8300 Electric Strike Body

Sticky Shims (optional use)

.24-.32

2. Select the appropriate Plug In Connector that matches

system power and electrically connect as illustrated in

Diagram 2. For 12V AC/DC or 16V AC, the pigtail marked “12

VDC” should be used. For 24V AC/DC, the pigtail marked

“24 VDC” should be used. If no connector is present,

configure the wires as illustrated within Diagram 2.

3. Make sure that the electric strike is in correct mode of

operation. This electric strike ships in fail secure mode. If

you need to convert the unit to fail safe, see Diagram 3 on

page 3.

4. If using Latchbolt Monitor (LBM), see Diagram 4.

5. Attach the faceplate to the electric strike, using the #8-32

screws provided. Be sure that the ramps are on top of the

faceplate. (see Diagram 5 on page 3).

Installation Directions

1. Verify opening is plumb and square. For important detail,

see “Read Me” guide.

6. Prepare door jamb per the appropriate template detail

(see pages 4-6).

Prepare Strike

Evaluate Opening

7. If applicable, install mounting tabs using #10-32 screws.

Do not tighten.

8. If opening is not plumb and square, see “Read Me” guide

for recommended corrections.

9. Install the electric strike unit in jamb cutout, using

#12-24 screws provided (or wood screws where

necessary).

10. The deadlatch must not interfere with the 8000/8300

ramps (see Diagram 6 on page 3). If you need to adjust the

ramps, mark the centerline of the deadlatch onto the

8000/8300 faceplate. Remove the 8000/8300 electric strike

from jamb. Loosen screws and slide internal ramp until the

groove between the ramps aligns with the mark made on

the faceplate. Tighten the screws. (see Diagram 7 on page

3).

11. Connect wires from power source to the electric strike.

12. Reinstall electric strike, tighten the #12-24 screws and

verify clearance of deadlatch.

13. If applicable, tighten the #10-32 screws holding the

mounting tabs.

Finish Installing

Prepare Frame

CAUTION! Before connecting any device at the installation site, verify input voltage using a multimeter.

Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding

10% of the solenoid rating may cause severe damage to the unit and will void the warranty.

DIAGRAM 2: 12V to 24V CONVERSION

RED

RED/GREEN

BLACK

VIOLET

RED

BLACK

VIOLET

RED/GREEN

IF CONNECTOR IS MISSING

(+ 12 VDC)

(-NEG)

(+ 24 VDC)

(-NEG)

ELECTRIC

STRIKE

ELECTRIC

STRIKE

CONNECT

TOGETHER

CONNECT

TOGETHER

CONNECT

TOGETHER

Installation Diagrams

LBM WIRING

White

Orange Normally Open

Green Normally Closed

Common

DIAGRAM 4: LATCHBOLT MONITORDIAGRAM 3: FAIL SAFE TO FAIL SECURE

DIAGRAM 5: FACEPLATE INSTALLATION

Loosen screws, but do not

remove them

Move screws to the Fail Safe

position as shown

Tighten screws

DIAGRAM 7: VERTICAL ADJUSTABILITY

DIAGRAM 6: VERTICAL ALIGNMENT

Fail Safe*

Centerline

*Fire rating only applies to Fail

Secure units. Conversion to Fail

Safe negates fire rating on 8300

White

Orange

Green

1/8" [3]

NOTE: The 8000/8300 electric strike

with 801faceplate will fit right into

most standard ANSI A115.2, 1”

deep dustboxes (e.g. the Curries

E-1 preparation), requiring no

cutting.

If you elect to place the 8000/8300

into the existing dustbox, simply

drill for wire connections.

8000/8300 with 801 Faceplate

1-1/4” X 4-7/8” Square Corner Faceplate

ANSI Metal Jamb Installations

4-7/8" [124]

4-1/8" [105]

1-1/4" [32]

3-3/8" [86]

Cutout Templates

DIAGRAM 8: WIRE DRILLING

3/16" [4.8]

3/8" 3/4" [19]

1-1/32” [26.2]

[9.5]

Inches [mm]

Diameter

3-3/8" [86]

1/8" [3]

7-15/16" [202]

1-7/16" [36.5]

7-5/32" [182]

R 5/32" [4]

8000/8300 with 801A Faceplate

1-1/4” x 4-7/8” Radius Corner Faceplate

Aluminum Jamb Installations

8000/8300 with 802 Faceplate

1-7/16” x 7-15/16” Radius Corner Faceplate

Aluminum and Wood Jamb Installations

1/8" [3]

3-3/8" [86]

1-1/4"[32]

4-7/8" [124]

R 5/32" [4]

4-1/8" [105]

Cutout Templates

Remove additional material as

needed to provide clearance for

electric strike and wires. Then drill

for wires (see Diagram 8)

Inches [mm]

8000/8300 with 803 Faceplate

1-1/4” x 6-7/8” Radius Corner Faceplate

Aluminum Jamb Installations

8000/8300 with 805 Faceplate

1-3/8” x 9” Radius Corner Faceplate

Aluminum or Wood Jamb Installations

6-1/8" [156]

6-7/8" [175]

3-3/8" [86]

1-1/4" [32]

1/8" [3]

9" [228.4]

1-3/8" [35]

3-3/8" [86]

3/32" [2.4]

1/8" [3]

Cutout Template

3068006.003 rev A.

Remove additional material as

needed to provide clearance for

electric strike and wires. Then drill

for wires (see Diagram 8)

Inches [mm]

1-1/16

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerrar de Assa Abloy

Assa Abloy

Assa Abloy LOCKWOOD Sliding Door Latch Manual de usuario

Assa Abloy

Assa Abloy Sargent 8200 Series Manual de usuario

Assa Abloy

Assa Abloy Sargent 8200 Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin IN220 PoE Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario

Assa Abloy

Assa Abloy YALE 4600CK Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin UT5200 Series Guía de inicio rápido

Assa Abloy

Assa Abloy Sargent XC Series Manual de usuario

Assa Abloy

Assa Abloy Yale YDD424A Manual de usuario

Assa Abloy

Assa Abloy Sargent 8200 Series Manual de usuario

Assa Abloy

Assa Abloy Sargent 6500 Manual de instrucciones

Assa Abloy

Assa Abloy Yale 7370 Series Manual de usuario

Assa Abloy

Assa Abloy Yale Assure Lever YRL216 Instrucciones de montaje

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC216 Especificaciones técnicas

Assa Abloy

Assa Abloy SARGENT 115 Hospital Latch Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin FE6800 Series Manual de usuario

Assa Abloy

Assa Abloy Yale Real Living YRD210-ZW Especificaciones técnicas

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario

Assa Abloy

Assa Abloy Yale 5300 Series Manual de usuario

Assa Abloy

Assa Abloy VingCard Essence Manual de usuario

Assa Abloy

Assa Abloy ALARM CONTROLS Magnalock 1200DE Delayed... Manual

Assa Abloy

Assa Abloy Door Lock Manual de usuario

Assa Abloy

Assa Abloy OneSystem 309N Guía de instalación

Assa Abloy

Assa Abloy SARGENT Profile LK Series Manual de instalación

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario

Assa Abloy hes 8000 Series Manual de usuario

Manuales populares de Cerrar de otras marcas