Assa Abloy Sargent 8200 Series Manual de usuario

1-800-727-5477 • www.sargentlock.com

A8260D 11/21

Installation Instructions

7800 & 8200 Series Mortise Lock

Used with VN1 Escutcheon Trim and V Series Indicators

written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in dam-

age to the product and void the

factory warranty.

WARNING

1-800-727-5477 • www.sargentlock.com A8260D 11/21

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

Tools Required

TOC Table of Contents

1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Indicator Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3 Lock set configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4 Rehanding Indicator (if required). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

a Prepare Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

b Install Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

c Install Outside Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

d Install Inside Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

e Install Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

f Install Outside Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

g Perform Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

h Indicator Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

#2 & #3 Phillips

head screwdrivers

Flat blade

screwdriver

1/8”Allen

Wrench

3/32"Drill bit T-20 Torx Screw

with Tamper Pin

Driver

1-800-727-5477 • www.sargentlock.com

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

A8260D 11/21

Indicator Variants

Depending on function and option ordered, indicators are provided in

the following variations, these instructions detail how to install with

cylinder, however other variations follow similar instructions. (Figure1)

Contact factory for any questions.

Coin Turn - For

installation

on outside of

door.

Cylinder - For

installation

on inside or

outside of

door.

No input /

blank - For

installation

on inside or

outside of

door.

Thumbturn -

For installation

on inside of

door.

Figure1

Lock set configuration

To set function of multi-function lock or to re-hand, see instructions on

lock body.

Rehanding indicator (if required)

Indicator spindle cams MUST be oriented correctly per lock function and

door mounting location. Verify hand and bevel of door. (Figure2)

Left Hand

Hinges Left

Open Inward

Right Hand

Hinges Right

Open Inward

LHRB

Left Hand

Reverse Bevel

Hinges Left

Open Outward

RHRB

Right Hand

Reverse Bevel

Hinges Right

Open Outward

Figure2

Note:

Stand on outside of locked door when determining door hand.

Next, verify inside and/or outside indicators are handed correctly,

using Spindle Cam Position chart. (Figure3) If they are handed

correctly, skip to Step 5 "Prepare Door".

If they are not handed correctly:

1. Remove retaining pad and spindle cam from assembly. (Figure4)

2. Position spindle cam in correct direction for door hand. (Figure3)

Important:

• For thumbturn indicators, make sure thumbturn

is positioned in the 12 o’clock direction as

shown. (Figure5)

3. Slide spindle cam post into correct slot of display slide. (Figure4)

4. Re-seat retaining pad into original position.

5. Return indicator to the vacant/unlocked position for installation.

Scan this QR

code for the

Sargent Indicator

Handing Charts

Door Hand: RH / RHRB

Door Hand: LH / LHRB

Outside Indicator

Inside Indicator

Outside Indicator

Spindle Cam Position for Locks with Deadbolt (*and 56 function)

Door Hand: RH / RHRB

Door Hand: LH / LHRB

Outside Indicator

Inside Indicator

Outside Indicator

Spindle Cam Position for Locks without Deadbolt (*except 56 function)

Figure3

Figure4

Spindle

cam

Display

slide slot

Retaining

pad

Thumbturn

position

Figure5

1-800-727-5477 • www.sargentlock.com A8260D 11/21

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

aPrepare Door

bInstall Lock

Installation

Figure6

Prepare door for function holes, size, and location according to A8258 door

marker template, if not already prepped.

1. Verify strike location according to template. Clean out door pocket and door edge of debris.

2. Ensure handing of lock matches handing of door. Slide lock into door. (Figure6)

3. Temporarily hand tighten two (2) lock screws (#12 x 1-1/4"wood screws, or #12-24 x1/2"machine screws).

Notes:

• Keep door open until installation is complete.

cInstall Outside Trim

dInstall Inside Trim

Inside of door

Lock

Screws

Outside

of door

RH door

shown

1. Verify lock is in unlocked state (control hub slot should be vertical).

Also, verify indicator is in vacant/unlocked position.

2. Align trim posts with diagonal holes in door, be sure lever is horizontal. Slide outside

escutcheon assembly through lock body from outside door face. (Figure7)

Note:

If indicator is used on outside, align indicator spindle with control hub. Outside Escutcheon Assembly

Figure7

1. Slide spindle into lockbody hub. (Figure8)

2. Slide adapter and plate assembly over spindle.

3. Secure with two (2) #8-32 x 5/8" screws.

4. For Studio Collection levers only, use trim bushing over adapter plate.

5. Verify lock is in unlocked state (turn outside lever to ensure).

Also, Verify indicator is in vacant/unlocked position.

6. Align escutcheon over adapter and install inside escutcheon assembly onto

inside door face.

Note:

• If indicator is used on inside, align indicator spindle with control hub.

7. Through-bolt inside escutcheon to outside escutcheon with

two (2) #8-32 x 2-1/4"screws.

8. Install inside lever on adapter plate. Secure with set screw.

Note:

Screw heads should be visible on inside escutcheon.

Figure8

Inside

Escutcheon

Assembly

Studio

Collection

Trim

Bushing

Adapter Plate

Spindle

Lever

Set

screw

#8-32 x 2-1/4" screw

#8-32 x

2-1/4"

screw

#8-32 x

5/8" screws

1-800-727-5477 • www.sargentlock.com

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

A8260D 11/21

Installation, continued

eInstall Cylinder

fInstall Outside Front

1. Thread cylinder into lock until flush with escutcheon surface. (Figure9)

• Pull key slightly out of cylinder to help thread into lock body.

2. Tighten cylinder clamp screw with #1 Phillips screwdriver.

• Check operation and adjust cylinder if necessary.

Notes:

• SARGENT logo must be horizontal and on top. (Figure10)

• If double cylinder function is used, repeat steps 1 and 2 for second cylinder.

• Removable Core or Interchangeable Core cylinders require a control key (key

stamped with C) to remove and install the core. This is not provided standard;

it must be requested separately. If requesting 1-bitted control key, specify

113511 cut.

Cylinder

Clamp

Screw

Figure9

Incorrect

Key and cylinder must be rotated as shown.

Correct

Figure10

1. Tighten the two (2) lock screws completely. (Figure11)

2. Attach outside front with two (2) flat head screws #8-32 x 1/4".

gPerform Functional Check

DO NOT FORCE if resistance is encountered during functional check.

Refer back to Rehanding Indicator (if required) section to ensure

correct handing. Rehand if necessary.

1. Insert key into cylinder (if present) and rotate:

• Ensure there is no friction against lock case or any other obstructions.

2. Check key retracts latch:

• Key should rotate freely.

3. Throw deadbolt (if present):

• Check key retracts both deadbolt and latch.

4. Test levers:

• Confirm latch and deadbolt (if installed) retract.

5. Verify indicator displays correct status when locked and unlocked.

Figure11

Lock

screw

Outside

front

Lock screw

#8-32 x

1/4" screws

1-800-727-5477 • www.sargentlock.com A8260D 11/21

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

Indicator Parts List

* These parts are for 1-3/4"standard thickness doors. For other thicknesses, please contact factory.

Note:

Reference 8200 Series parts manual for all lock body parts.

Figure12

Figure12 Description Part Number Req.

1 VN1 Indicator Escutcheon Consult Factory 1

2 Indicator Window 81-0811 1

Indicator Display Assembly - Green Unlocked / Red Locked 82-5602

Indicator Display Assembly - Green Vacant / Red Occupied 82-5603

Indicator Display Assembly - Green Unlocked Icon / Red Locked Icon 82-5604

Indicator Display Assembly - White Unlocked / Red Locked 82-5605

Indicator Display Assembly - White Vacant / Red Occupied 82-5606

Indicator Display Assembly - White Unlocked Icon / Red Locked Icon 82-5607

4A Indicator Spindle Cam - Thumbturn / Coin Turn 81-0745 1

4B Indicator Spindle Cam - Cylinder / No Input / Blank 81-0756* 1

4C Indicator Spindle Cam - 05, 37, 38, 59 Functions 81-5577* 1

5 Indicator Backing Plate 81-0748 1

6 VN1 Escutcheon Screw Pack (Not shown) 82-5587 x finish* 1

7 Door Marker Template (Not shown) A8258 1

1-800-727-5477 • www.sargentlock.com

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

A8260D 11/21

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov. A8260D 11/21

Otros manuales para Sargent 8200 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerradura de puerta de Assa Abloy

Assa Abloy

Assa Abloy effeff Mini Shear Magnet Manual de usuario

Assa Abloy

Assa Abloy NORTON RIXSON M19 Manual de usuario

Assa Abloy

Assa Abloy SARGENT KP8977 Guía

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Manual de usuario

Assa Abloy

Assa Abloy ESA500 Manual de instalación

Assa Abloy

Assa Abloy 179B S4 Guía del usuario

Assa Abloy

Assa Abloy Yale Essential Series Manual de usuario

Assa Abloy

Assa Abloy SARGENT 5300 Series Manual de usuario

Assa Abloy

Assa Abloy SARGENT IN120 Wi-Fi Series Manual de usuario

Assa Abloy

Assa Abloy Yale 446F Manual de usuario

Assa Abloy

Assa Abloy effeff ANYKEY 496 Manual de usuario

Assa Abloy

Assa Abloy Yale Real Living YRD210-ZW Especificaciones técnicas

Assa Abloy

Assa Abloy Lockwood 8653 Manual de usuario

Assa Abloy

Assa Abloy Rixson 73ER Manual de usuario

Assa Abloy

Assa Abloy Sargent AL-PE80 Series Manual de usuario

Assa Abloy

Assa Abloy effeff 827A-IP Manual de usuario

Assa Abloy

Assa Abloy ES100 Series Manual de usuario

Assa Abloy

Assa Abloy besam US23-0696-01 Manual de programación

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Manual de usuario

Assa Abloy

Assa Abloy Sargent PR100 Manual de usuario

Assa Abloy

Assa Abloy IKON VERSO CLIQ Manual de usuario

Assa Abloy

Assa Abloy Yale nexTouch NTB610 Especificaciones técnicas

Assa Abloy

Assa Abloy Yale Doorman Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin ED3400 Series Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario

Saflok

Saflok Quantum ädesē RFID Manual de usuario