Assa Abloy SARGENT 5300 Series Manual de usuario

Installation Instructions

1-800-727-5477 • www.sargentlock.com A8255A 08/19

part without the express written permission of SARGENT Manufacturing Company is prohibited.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

5300 Series

Alarmed Exit Devices

ATTENTION INSTALLER

Disconnect all input power before beginning installation

to prevent electrical shock and equipment damage.

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

TOC Table of Contents

1 General Description .............................................................3

2 Contents ........................................................................3

a Package Contents ...............................................................3

b Miscellaneous Parts .............................................................4

3 Dip Switch (SW-2, 6-position) ...................................................4

4 AL - Circuit Board ................................................................5

5 Installation Instructions .........................................................6

6 Apply Rail Assembly .............................................................7

7 Cylinder Installation .............................................................7

a Door Preparation................................................................7

b Add or Remove Cylinder.........................................................8

c Installation and Orientation of Cylinder ..........................................8

8 Alarmed Exit (5300) Standard Operating Instructions ...........................9

a Arm Alarm ......................................................................9

b Security/Tamper Violation .......................................................9

c Low Battery Alert ...............................................................9

9 Optional Features ............................................................. 10

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

1 General Description

The SARGENT Alarmed Exit is designed for areas that require an alarm to sound upon exiting. Once armed,

any push rail movement will activate the horn in the push rail. The horn will continue to sound for two (2)

minutes and shut off automatically. The LED will flash, indicating a violation has occurred.

Alarmed Exit

Circuitry Figure1

Manual dogging is provided standard

on non fire rated devices

2 Contents

a Package Contents

Figure2

Figure 2 Description

1 Mounting Rail, Wilde Stile

2 Chassis Assembly (Wide)

3 5300 Cover, Chassis

4 End Cap Bracket

5 End Cap

6 Pull (Sold Separately)

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

2 Contents (cont.)

b Miscellaneous Parts

Endcap

Mounting Plate

Exit device

chassis and rail

assembly shown

Chassis

Assembly

Cover Mounting rail insert

Figure3

3 Dip Switch (SW-2, 6-position)

Factory settings shown.

1. DS-1 = OFF, DS-2 = OFF - REX / Passage Delay

(set to 7 seconds).

2. DS-3 = OFF, DS-4 = OFF - Automatic Alarm

Reset (set to 2 minutes).

3. DS-5 = ON - Selects LED color (Armed = Green,

Violation = Red, Passage = Yellow).

4. DS-6 = ON - Monitor Relay is enabled (will

activate when rail is violated).

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

4 AL - Circuit Board

Printed Circuit Board:

Figure4

Note

SW-1, Arm/Disarm Switch shown in ON (armed) position.

Insert with circuit board:

Battery

Figure5

OFF

SW-2 6-position

dip switch

SW-1

Arm/Disarm

switch

6 5 4 3 2 1

Figure6

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

5 Installation Instructions

• These instructions are for the 5300 Series exit device, which is designed for areas requiring field

selectable time delay and automatic alarm reset options.

• Verify hand and bevel of door. Exit devices are always reverse bevel and are mounted on inside of

door.

Left Hand Reverse Bevel Hinges

Left. Open Outward LHRB

Inside View Outside View Inside View Outside View

Right Hand Reverse Bevel Hinges

Left. Open Outward RHRB

LHRB Shown RHRB Shown

Figure7

5. Installation must be performed by a trained and experienced service person.

6. 9V battery operated.

7. No external wires.

Note:

For retrofit applications, refer to retrofit instructions.

Figure8

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

6 Apply Rail Assembly

1. Depress lift arm into rail assembly and slide rail onto chassis.

2. Attach rail assembly to chassis with two (2) #8 truss head machine screws. Do not tighten screws

(Figure9).

3. Secure chassis to door with four (4) #10 flat head screws. (Figure8)

4. Level rail.

5. Place mounting plate tight against rail and attach to door with two (2) #10 round head screws.

6. Tighten all screws securely (Figure10).

Figure9

Lift Arm Level Mounting Plate

Rail Assembly

Rail Mounting Screw (2 Places)

(#8-32 x 3/8 PH. Truss HD. Machine Screw)

Mounting Plate

Mounting Plate Screws

(#10-24 x 3/4"PH. RD. HD. Machine Screw)

Figure10

Chassis Mounting Screws

(1/4-20 x5/8 PH. FL. HD.

Machine Screws)

Four (4) places

Figure11

7 Cylinder Installation

a Door Preparation

1. Prepare door according to template.

2. Verify size 41 cylinder is installed in rail insert with collar prior to installing exit device on door.

NOTE: Use caution not to damage wires when installing cylinder nut.

Collar

Cylinder nut

Side View. Battery holder

not shown.

Use caution not to dam-

age wires when installing

cylinder nut.

Figure12

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

7 Cylinder Installation (cont.)

b Add or Remove Cylinder

3. Remove insert assembly from rail by sliding toward rail end.

Figure13

c Installation and Orientation of Cylinder

1. Slide cylinder through collar into insert as shown.

2. Note orientation of cylinder.

3. Secure cylinder with cylinder nut, tightening firmly.

4. Operate cylinder and verify cam is operating switch properly.

Figure14

Figure15

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

8 Alarmed Exit (5300) Standard Operating Instructions

a Arm Alarm

Turn key clockwise. Yellow PASSAGE LED will flash for

15 seconds (default), then a quick chirp and ARMED

green LED will flash and repeat every 30 seconds.

Signal above cylinder indicates unit is armed.

NOTE: Unit is automatically armed 15 seconds after

it is turned on. Field selectable settings listed at

bottom of page.

b Security/Tamper Violation

When ARMED, depressing the push rail will activate alarm.

Horn will sound and red violation LED will flash. The horn

will continue to sound for two (2) minutes (default).

After two (2) minutes, unit will reset on its own and red

LED will flash every 30 seconds until rearmed using the

key. Turn key counter-clockwise to deactivate alarm.

Turn key clockwise to rearm alarm.

c Low Battery Alert

Horn chirps intermittently to indicate low battery

condition. Replace 9-volt alkaline battery.

Figure16

Figure17

Figure18

5300 Series

Installation Instructions

Alarmed Exit Devices

A8255A 08/191-800-727-5477 • www.sargentlock.com

part without the express written permission of SARGENT Manufacturing Company is prohibited.

9 Optional Features

Once power is connected, turn key clockwise to activate alarm. A time delay of 7, 10, 15 or 20 seconds

initiates prior to rail going into an armed state. This allows individualized alarm setting. LED will flash

yellow during this time.

Horn will chirp one (1) time. LED will flash green and repeat every 30 seconds to indicate unit is armed.

Once armed, depress push bar to sound alarm. Rail alarm will sound until disarmed using one (1) of the

following methods:

1. Rail cylinder key

2. Automatic reset (after optional field settable time delay of 2, 5 or 10 minutes)

LED will flash red every 30 seconds to indicate rail has been violated and will continue to flash red until

unit is reset manually. If battery powered and low battery voltage is detected, horn chirps quickly and

repeats every 10 seconds until battery is replaced.

These field selectable switches can change the following functions:

Auto Alarm Reset Request to Exit/Passage Time Delay

DS3 DS4 Timer Reset DS1 DS2 Timer Reset

Off Off 2 minutes Off Off 7 seconds

Off On 5 minutes Off On 10 seconds

On Off 10 minutes On Off 15 seconds

On On Continuous On On 20 seconds

Tabla de contenidos

Otros manuales de Cerradura de puerta de Assa Abloy

Assa Abloy

Assa Abloy Corbin Russwin CLX3300 Series Manual de usuario

Assa Abloy

Assa Abloy KESO Genie Manual de usuario

Assa Abloy

Assa Abloy shine Manual de usuario

Assa Abloy

Assa Abloy LOCKWOOD 3782 Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 Series Manual de usuario

Assa Abloy

Assa Abloy AUE100 Aperio Manual de usuario

Assa Abloy

Assa Abloy Valencia AJAX Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin ED5800 Series Manual de usuario

Assa Abloy

Assa Abloy Hes 5200 Series Manual de usuario

Assa Abloy

Assa Abloy Sargent FM-PE8700 Series Manual de usuario

Assa Abloy

Assa Abloy ADAMS RITE 4300 Series Manual de usuario

Assa Abloy

Assa Abloy Sargent PE8893 Manual de usuario

Assa Abloy

Assa Abloy Lockwood CAVITY LOCK Manual de usuario

Assa Abloy

Assa Abloy CL33700 TCPWI1 Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin HP3000 Series Manual de usuario

Assa Abloy

Assa Abloy Lockwood Standalone Manual

Assa Abloy

Assa Abloy Sargent PE8400 Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin Access 800 TCAC2 Series Manual de instalación

Assa Abloy

Assa Abloy EL580 Manual de usuario

Assa Abloy

Assa Abloy Yale PAS3621 Manual de usuario

Assa Abloy

Assa Abloy eCLIQ Manual de usuario

Assa Abloy

Assa Abloy DC423.2 Manual de usuario

Assa Abloy

Assa Abloy Connect 310 Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario

Saflok

Saflok Quantum ädesē RFID Manual de usuario