Anritsu MT9812B Manual de usuario

Document No.: M-W1555AE-9.0

ANRITSU CORPORATION

MT9812B

Multi Channel Box

Operation Manual

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

Ninth Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings

of the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols

and take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MT9812B

Multi Channel Box

Operation Manual

1 February 1999 (First Edition)

9 May 2008 (Ninth Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

WARNING

1. ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the

left may also be used with other marks and descriptions to indicate

other dangers.

2. IEC 61010 Standard

The IEC 61010 standard specifies four categories to ensure that an

instrument is used only at locations where it is safe to make

measurements. This instrument is designed for measurement

category I (CAT I). DO NOT use this instrument at locations

specified as category II, III, or IV as defined below.

Measurement category I (CAT I):

Secondary circuits of a device that is not directly connected to a

power outlet.

Measurement category II (CAT II):

Primary circuits of a device that is directly connected to a power outlet,

e.g., portable tools or home appliance.

Measurement category III (CAT III):

Primary circuits of a device (fixed equipment) to which power is

supplied directly from the distribution panel, and circuits running from

the distribution panel to power outlet.

Measurement category IV (CAT IV):

Building service-line entrance circuits, and circuits running from the

service-line entrance to the meter or primary circuit breaker

(distribution panel).

For Safety

WARNING

3. Laser radiation warning

•NEVER look directly into the cable connector on the equipment

nor into the end of a cable connected to the equipment. There is

a risk of injury if laser radiation enters the eye.

•The Laser Safety label is attached to the equipment for safety use

as indicated in "Laser Safety" later in this section.

4. To ensure that the instrument is earthed, always use the supplied 3-

pin power cord, and insert the plug into an outlet with an earth

terminal. If power is supplied without earthing the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

5. This equipment cannot be repaired by the operator. DO NOT attempt

to remove the equipment covers or unit covers or to disassemble

internal components. Only qualified service personnel with a

knowledge of electrical fire and shock hazards should service this

equipment. There are high-voltage parts in this equipment presenting

a risk of severe injury or fatal electric shock to untrained personnel. In

addition, there is a risk of damage to precision components.

6. The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu service

personnel, or service personnel of an Anritsu sales representative,

should break this seal to repair or calibrate the equipment. If the

performance-guarantee seal is broken by you or a third party, the

performance of the equipment cannot be guaranteed. Be careful not

to break the seal by opening the equipment or unit covers.

7. This equipment should always be positioned in the correct manner.

If the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

Repair

Falling Over

Electric Shock

Calibration

For Safety

CAUTION

1. Always remove the mains power cable from the power outlet before

replacing blown fuses. There is a risk of electric shock if fuses are

replaced with the power cable connected. Always use new fuses of

the type and rating specified on the rear panel of the instrument.

There is a risk of fire if a fuse of a different rating is used.

T5A indicates a time-lag fuse.

2. Keep the power supply and cooling fan free of dust.

•Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

•Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

Fuse Replacement

Cleaning

For Safety

Class 1, 1M indicate the danger degree of the laser radiation specified

below according to IEC 60825-1:2001.

Class 1: Lasers that are safe under reasonably foreseeable conditions

of operation, including the use of optical instruments for

intrabeam viewing.

Class 1M: Lasers emitting in the wavelength range from 302.5 to 4000

nm that are safe under reasonably foreseeable conditions of

operation, but may be hazardous if the user employs optics

within the beam. Two conditions apply:

a) for diverging beams, if the user views the laser output with

certain optical instruments (for example, eye loupes,

magnifiers and microscopes) within a distance of 100 mm;

b) for collimated beams, if the user views the laser output with

certain optical instruments (for example, telescopes and

binoculars).

Class I, IIa, II, IIIa, IIIb indicate the degree of danger of the laser radiation

outlined below as defined by 21 CFR 1040.10:1995.

Class I: Class I levels of laser radiation are not considered to be

hazardous.

Class IIa: Class IIa levels of laser radiation are not considered to be

hazardous if viewed for any period of time less than or equal

to 1×103seconds but are considered to be a chronic viewing

hazard for any period of time greater than 1×103seconds.

The wavelength range of laser radiating is in 400 to 710 nm.

Class II: Class II levels of laser radiation are considered to be a chronic

viewing hazard. The wavelength range of laser radiating is

in 400 to 710 nm.

Class IIIa: Class IIIa levels of laser radiation are considered to be,

depending upon the irradiance, either an acute intrabeam

viewing hazard or chronic viewing hazard, and an acute

viewing hazard if viewed directly with optical instruments.

The wavelength range of laser radiating is in 400 to 710 nm.

Class IIIb: Class IIIb levels of laser radiation are considered to be an

acute hazard to skin and eyes from direct radiation.

For Safety

vii

CAUTION

Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

The use of optical instruments with this product will increase eye hazard.

For Safety

viii

WARNING

Before using this instrument, always ensure that the warning light is lit

when the optical output switch is turned on.

If this warning light does not turn on, the equipment may be faulty and for

safety reasons should be returned to an Anritsu service center or

representative for repair.

The laser in the plug-in unit provided for this equipment is classified as

Class 1, 1M according to the IEC 60825-1:2001 standard, or as Class I,

IIIb according to the 21 CFR 1040.10:1995 standard.

Never use optical instruments to directly view Class 1M laser products.

Doing so may result in serious damage to the eyes.

Table 1 Laser Safety Classifications Based on IEC 60825-1:2001

Model Name Class Max. Optical

Output Power (mW)*

Pulse Width (s)/

Repetition Rate

Emitted

Wavelength (nm) Laser Aperture

MU954501A Class 1 10 CW 1550 Fig. 1, [1]

MU952501A Class 1M 40 CW 1545-1553 Fig. 1, [1]

MU952502A Class 1M 40 CW 1553-1561 Fig. 1, [1]

MU952503A Class 1M 40 CW 1561-1564 Fig. 1, [1]

MU952504A Class 1M 40 CW 1537-1545 Fig. 1, [1]

MU952505A Class 1M 40 CW 1530-1537 Fig. 1, [1]

MU952601A Class 1M 40 CW 1564-1569 Fig. 1, [1]

MU952602A Class 1M 40 CW 1569-1578 Fig. 1, [1]

MU952603A Class 1M 40 CW 1577-1586 Fig. 1, [1]

MU952604A Class 1M 40 CW 1586-1594 Fig. 1, [1]

MU952605A Class 1M 40 CW 1594-1603 Fig. 1, [1]

MU952606A Class 1M 40 CW 1603-1610 Fig. 1, [1]

MU951301A Class 1M 40 CW 1310 Fig. 1, [1]

MU951501A Class 1M 40 CW 1550 Fig. 1, [1]

MU951001A Class 1M 40 CW 1310/1550 Fig. 1, [1]

*: Indicates the possible optical output power when each and every

reasonably foreseeable single-fault condition is included.

Laser Safety

For Safety

Table 2 Laser Safety Classifications Based on FDA21 CFR 1040.10:1995

Model Name Class Max. Optical

Output Power (mW)

Pulse Width (s)/

Repetition Rate

Emitted

Wavelength (nm) Laser Aperture

MU954501A Class I 10 CW 1550 Fig. 1, [1]

MU952501A Class IIIb 40 CW 1545-1553 Fig. 1, [1]

MU952502A Class IIIb 40 CW 1553-1561 Fig. 1, [1]

MU952503A Class IIIb 40 CW 1561-1564 Fig. 1, [1]

MU952504A Class IIIb 40 CW 1537-1545 Fig. 1, [1]

MU952505A Class IIIb 40 CW 1530-1537 Fig. 1, [1]

MU952601A Class IIIb 40 CW 1564-1569 Fig. 1, [1]

MU952602A Class IIIb 40 CW 1569-1578 Fig. 1, [1]

MU952603A Class IIIb 40 CW 1577-1586 Fig. 1, [1]

MU952604A Class IIIb 40 CW 1586-1594 Fig. 1, [1]

MU952605A Class IIIb 40 CW 1594-1603 Fig. 1, [1]

MU952606A Class IIIb 40 CW 1603-1610 Fig. 1, [1]

MU951301A Class IIIb 40 CW 1310 Fig. 1, [1]

MU951501A Class IIIb 40 CW 1550 Fig. 1, [1]

MU951001A Class IIIb 40 CW 1310/1550 Fig. 1, [1]

For Safety

Table 3 Indication Labels on Product

Type Sample Affixed to: Model Name

1 Explanation Fig. 1, A MU954501A

2 Explanation Fig. 1, B

MU952501A/02A/03A/04A/05A

MU952601A/02A/03A/04A/05A/06A

MU951301A

MU951501A

MU951001A

3 Explanation Fig. 1, C

MU952501A/02A/03A/04A/05A

MU952601A/02A/03A/04A/05A/06A

MU951301A

MU951501A

MU951001A

4 Certification Fig. 1, D MT9810B

MT9812B

5 Identification Fig. 1, E MT9810B

MT9812B

6 Warning Fig. 1, F

MU954501A

MU952501A/02A/03A/04A/05A

MU952601A/02A/03A/04A/05A/06A

MU951301A

MU951501A

MU951001A

7 Aperture Fig. 1, G

MU954501A

MU952501A/02A/03A/04A/05A

MU952601A/02A/03A/04A/05A/06A

MU951301A

MU951501A

MU951001A

Otros manuales para MT9812B

Tabla de contenidos

Otros manuales de Equipo de prueba de Anritsu

Anritsu

Anritsu MD8470A Manual de usuario

Anritsu

Anritsu MP8931A Manual de usuario

Anritsu

Anritsu OSL Series Manual de uso y cuidado

Anritsu

Anritsu MP2110A BERTWave Manual de usuario

Anritsu

Anritsu MT8870A Manual de usuario

Anritsu

Anritsu MT9810A Manual de usuario

Anritsu

Anritsu Network Master Series Manual de usuario

Anritsu

Anritsu Site Master S112 Manual de usuario

Anritsu

Anritsu 3656B W1 Manual de usuario

Anritsu

Anritsu MD8480A Manual de usuario

Anritsu

Anritsu MD1230B-26 Manual de usuario

Anritsu

Anritsu MG3641A Manual de usuario

Anritsu

Anritsu VectorStar MN4690B Series Manual de usuario

Anritsu

Anritsu SQA-R MP1900A Manual de referencia

Anritsu

Anritsu OSL Series Manual de usuario

Anritsu

Anritsu MU150101A Manual de usuario

Anritsu

Anritsu MS8608A Manual de usuario

Anritsu

Anritsu Network master Pro Manual de usuario

Anritsu

Anritsu MS8911A Manual de usuario

Anritsu

Anritsu AutoCal 36581NNF Manual de usuario

Anritsu

Anritsu MT8860B Manual del propietario

Anritsu

Anritsu Site Master S330A Manual de usuario

Anritsu

Anritsu MT8852A Manual de usuario

Anritsu

Anritsu CMA50 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario