Anritsu MP1590B Manual de usuario

Document No.: M-W2420AE-21.0

ANRITSU CORPORATION

MP1590B

Network Performance Tester

Operation Manual

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

21st Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of

the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MP1590B

Network Performance Tester

Operation Manual

1 September 2004 (First Edition)

18 October 2013 (21st Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

WARNING

•ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the left

may also be used with other marks and descriptions to indicate other

dangers.

•Overvoltage Category

This equipment complies with overvoltage category II defined in IEC

61010. DO NOT connect this equipment to the power supply of

overvoltage category III or IV.

•Laser radiation warning

•NEVER look directly into the cable connector on the equipment

nor into the end of a cable connected to the equipment. There is a

risk of injury if laser radiation enters the eye.

•The Laser Safety label is attached to the equipment for safety use

as indicated in "Laser Safety" later in this section.

•To ensure that the equipment is grounded, always use the supplied

3-pin power cord, and insert the plug into an outlet with a ground

terminal. If power is supplied without grounding the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

•Only qualified service personnel with a knowledge of electrical fire and

shock hazards should service this equipment. This equipment cannot

be repaired by the operator. DO NOT attempt to remove the

equipment covers or unit covers or to disassemble internal

components. There are high-voltage parts in this equipment

presenting a risk of severe injury or fatal electric shock to untrained

personnel. In addition, there is a risk of damage to precision

components.

Electric Shock

Repair

For Safety

WARNING

•The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu

service personnel, or service personnel of an Anritsu sales

representative, should break this seal to repair or calibrate the

equipment. Be careful not to break the seal by opening the

equipment or unit covers. If the performance-guarantee seal is

broken by you or a third party, the performance of the equipment

cannot be guaranteed.

•This equipment should always be positioned in the correct manner. If

the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

•When replacing the battery, use the specified battery and insert it

with the correct polarity. If the wrong battery is used, or if the battery

is inserted with reversed polarity, there is a risk of explosion causing

severe injury or death.

Falling Over

Replacing Battery

Calibration

For Safety

WARNING

•DO NOT short the battery terminals and never attempt to disassemble

the battery or dispose of it in a fire. If the battery is damaged by any of

these actions, the battery fluid may leak. This fluid is poisonous.

DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is

accidentally ingested, spit it out immediately, rinse your mouth with

water and seek medical help. If it enters your eyes accidentally, do

not rub your eyes, rinse them with clean running water and seek

medical help. If the liquid gets on your skin or clothes, wash it off

carefully and thoroughly.

•DO NOT expose batteries to heat or fire. Do not expose batteries to

fire. This is dangerous and can result in explosions or fire. Heating

batteries may cause them to leak or explode.

•This equipment uses a Liquid Crystal Display (LCD). DO NOT subject

the equipment to excessive force or drop it. If the LCD is subjected to

strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested

accidentally, spit it out immediately, rinse your mouth with water and

seek medical help. If it enters your eyes accidentally, do not rub your

eyes, rinse them with clean running water and seek medical help. If

the liquid gets on your skin or clothes, wash it off carefully and

thoroughly.

Battery Fluid

LCD

Battery Disposal

For Safety

CAUTION

•Always remove the mains power cable from the power outlet before

replacing blown fuses. There is a risk of electric shock if fuses are

replaced with the power cable connected. Replace the fuses with the

same type. Failure to do so may result in fire.

T10A indicates a time-lag fuse.

•Always remove the main power cable from the power outlet before

cleaning dust around the power supply and fan.

•Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

•Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

•Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

Check Terminal

Fuse Replacement

Cleaning

For Safety

vii

Class 1, 1M indicate the danger degree of the laser radiation specified

below according to IEC 60825-1:2007.

Class 1: Lasers that are safe under reasonably foreseeable conditions

of operation, including the use of optical instruments for

intrabeam viewing.

Class 1M: Lasers emitting in the wavelength range from 302.5 to 4000

nm that are safe under reasonably foreseeable conditions of

operation, but may be hazardous if the user employs optics

within the beam. Two conditions apply:

a) for diverging beams, if the user views the laser output with

certain optical instruments (for example, eye loupes,

magnifiers and microscopes) within a distance of 100 mm;

b) for collimated beams, if the user views the laser output

with certain optical instruments (for example, telescopes

and binoculars).

CAUTION

Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

The use of optical instruments with this product will increase eye

hazard.

WARNING

The laser in the plug-in unit provided for this equipment is classified as

Class 1 or 1M according to the IEC 60825-1:2007 standard and is safe

under reasonably foreseeable operating conditions.

Never use optical instruments to directly view Class 1M laser products.

Doing so may result in serious damage to the eyes.

Laser Safety

For Safety

viii

Table 1 Laser Safety Classifications Based on IEC 60825-1:2007

Model Name Class

Max.

Optical

Output

Power

(mW)*

Pulse

Width (s)/

Repetition

Rate

Emitted

Wavelength

(nm)

Beam

Divergence

(deg)

Incorporated

Laser

Specification

(refer to Table

Laser

Aperture

MU120112A 1

0.4 CW 850 32.0 G0105A

Figure 1,

[1]

2.6 CW 1310 11.5 G0107A

2.6 CW 1550 11.5 G0108A

MU120118B 1

0.74 CW 850 23.0 G0277A

Figure 2,

[1]

1.2 CW 1310 11.5 G0192A

2.6 CW 1550 11.5 G0193A

MU120118C 1

0.74 CW 850 23.0 G0277A

Figure 3,

[1]

1.2 CW 1310 11.5 G0192A

2.6 CW 1550 11.5 G0193A

MU120122A 1

0.6 CW 850 32.0 G0181A

Figure 4,

[1]

2.0 CW 1310 11.5 G0183A

3.2 CW 1550 11.5 G0184A

MU120132A 1

0.6 CW 850 32.0 G0181A

Figure 5,

[1]

2.0 CW 1310 11.5 G0182A

3.2 CW 1550 11.5 G0184A

MU120138A

1M 0.8 CW 850 32.0 G0238A

Figure 6,

[1]

1 1.2 CW 1310 11.5 G0239A

2.6 CW 1550 11.5 G0271A

MU150100A 1 2.0 CW 1310 11.5 a) Figure 7,

[1]

2.0 CW 1550 11.5 b)

MU150101A 1 2.0 CW 1310 11.5 a) Figure 8,

[1]

2.0 CW 1550 11.5 b)

MU150110A 1

0.8 CW 1310 11.5 G0194A

Figure 9,

[1]

1.6 CW 1550 11.5 G0195A

2.0 CW 1310 11.5 c) Figure 9,

[2]

2.0 CW 1550 11.5 d)

MU150121A 1 2.0 CW 1310 11.5 e)

Figure 10,

[1]

2.0 CW 1550 11.5 f)

*: Indicates the possible optical output power when each and every

reasonably foreseeable single-fault condition is included.

For Safety

Table 1 Laser Safety Classifications Based on IEC 60825-1:2007 (Cont’d)

Model Name Class

Max.

Optical

Output

Power

(mW)*

Pulse Width

(s)/

Repetition

Rate

Emitted

Wavelength

(nm)

Beam

Divergence

(deg)

Incorporated

Laser

Specification

(refer to Table 2)

Laser

Aperture

MU150121B 1 2.0 CW 1310 11.5 e) Figure

11, [1]

2.0 CW 1550 11.5 f)

MU150135A 1 0.8 CW 1310 11.5 G0194A

Figure

12, [1]

1.6 CW 1550 11.5 G0195A

The following products are now discontinued.

For Laser Safety Classifications of the discontinued products, see

MP1590B Network Performance Tester Operation Manual, 15th Edition.

MU120102A, MU120118A, MU150134A

For Safety

Table 2 Incorporated Laser Specification

Incorporated

Laser

Max. Optical

Output Power

(mW)*

Pulse Width

(s)/

Repetition

Rate

Emitted

Wavelength

(nm)

Beam

Divergence

(deg)

G0105A 0.4 CW 850 32.0

G0107A 2.6 CW 1310 11.5

G0108A 2.6 CW 1550 11.5

G0181A 0.6 CW 850 32.0

G0183A 2.0 CW 1310 11.5

G0184A 3.2 CW 1550 11.5

G0192A 1.2 CW 1310 11.5

G0193A 2.6 CW 1550 11.5

G0194A 0.8 CW 1310 11.5

G0195A 1.6 CW 1550 11.5

G0238A 0.8 CW 850 32.0

G0239A 1.2 CW 1310 11.5

G0271A 2.6 CW 1550 11.5

G0277A 0.74 CW 850 23.0

a) 9.4 CW 1310 11.5

b) 9.4 CW 1550 11.5

c) 4.0 CW 1310 11.5

d) 4.0 CW 1550 11.5

e) 3.2 CW 1310 11.5

f) 3.2 CW 1550 11.5

*：Maximum output power is the estimated value when something

breaks down.

Otros manuales para MP1590B

Tabla de contenidos

Otros manuales de Equipo de prueba de Anritsu

Anritsu

Anritsu MS8608A Manual de usuario

Anritsu

Anritsu MT9812B Manual de usuario

Anritsu

Anritsu MT9812B Manual de usuario

Anritsu

Anritsu LMR Master S412E Manual del propietario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu MD1230B-26 Manual de usuario

Anritsu

Anritsu Precision AutoCal 36585 Series Manual de usuario

Anritsu

Anritsu InterferenceHunter MA2700A Manual de usuario

Anritsu

Anritsu VectorStar MN4690B Series Manual de usuario

Anritsu

Anritsu MG369 A Series Manual de usuario

Anritsu

Anritsu OSL Series Manual de usuario

Anritsu

Anritsu MT9810A Manual de usuario

Anritsu

Anritsu MT8860C Manual de usuario

Anritsu

Anritsu 693 B Series Manual de usuario

Anritsu

Anritsu MT9810A Manual de usuario

Anritsu

Anritsu MP1800A Manual de usuario

Anritsu

Anritsu MT9810B Manual de usuario

Anritsu

Anritsu MU150101A Manual de usuario

Anritsu

Anritsu MP8931A Manual de usuario

Anritsu

Anritsu Site Master S113B Manual de usuario

Anritsu

Anritsu CMA50 Manual de usuario

Anritsu

Anritsu Network Master Series Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu 681XXC Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario