Anritsu MT8860B Manual del propietario

MT8860B

Remote Programming Manual

WLAN Test Set

Remote Programming Manual

MT8860B

WLAN Test Set

Anritsu Company

490 Jarvis Drive

Morgan Hill, CA 95037-2809

USA

P/N: 13000-00202

Revision: J

Printed: September 2009

WARRANTY

The Anritsu product(s) listed on the title page is warranted against defects in materials and

workmanship for one year from the date of shipment.

Anritsu’s obligation covers repairing or replacing products which prove to be defective during the

warranty period. Buyers shall prepay transportation charges for equipment returned to Anritsu

for warranty repairs. Obligation is limited to the original purchaser. Anritsu is not liable for

consequential damages.

LIMITATION OF WARRANTY

The foregoing warranty does not apply to Anritsu connectors that have failed due to normal wear.

Also, the warranty does not apply to defects resulting from improper or inadequate maintenance

by the Buyer, unauthorized modification or misuse, or operation outside of the environmental

specifications of the product. No other warranty is expressed or implied, and the remedies

provided herein are the Buyer’s sole and exclusive remedies.

DISCLAIMER OF WARRANTY

DISCLAIMER OF WARRANTIES. TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, ANRITSU COMPANY AND ITS SUPPLIERS DISCLAIM ALL

WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, WITH REGARD TO THE SOFTWARE PRODUCT. THE USER ASSUMES THE

ENTIRE RISK OF USING THE PROGRAM. ANY LIABILITY OF PROVIDER OR

MANUFACTURER WILL BE LIMITED EXCLUSIVELY TO PRODUCT REPLACEMENT.

NO LIABILITY FOR CONSEQUENTIAL DAMAGES. TO THE MAXIMUM EXTENT

PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ANRITSU COMPANY OR ITS

SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR

CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,

DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF

BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE

USE OF OR INABILITY TO USE THE SOFTWARE PRODUCTS, EVEN IF ANRITSU

COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE

SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE

LIMITATION MAY NOT APPLY TO YOU.

TRADEMARK ACKNOWLEDGMENTS

Windows Vista and Windows XP are registered trademarks of Microsoft Corporation.

Acrobat Reader is a registered trademark of Adobe Corporation.

NOTICE

Anritsu Company has prepared this manual for use by Anritsu Company personnel and customers

as a guide for the proper installation, operation and maintenance of Anritsu Company equipment

and computer programs. The drawings, specifications, and information contained herein are the

property of Anritsu Company, and any unauthorized use or disclosure of these drawings,

specifications, and information is prohibited; they shall not be reproduced, copied, or used in whole

or in part as the basis for manufacture or sale of the equipment or software programs without the

prior written consent of Anritsu Company.

UPDATES

Updates, if any, can be downloaded from the Documents area of the Anritsu web site at:

http://www.us.anritsu.com

Materials Declaration for the People’s Republic of China

CE Conformity Marking

Anritsu affixes the CE Conformity marking onto its conforming products in accordance with

Council Directives of The Council Of The European Communities in order to indicate that

these products conform to the EMC and LVD directive of the European Union (EU).

C-tick Conformity Marking

Anritsu affixes the C-tick marking onto its conforming products in accordance with the

electromagnetic compliance regulations of Australia and New Zealand in order to indicate

that these products conform to the EMC regulations of Australia and New Zealand.

Notes On Export Management

This product and its manuals may require an Export License or approval by the government

of the product country of origin for re-export from your country.

Before you export this product or any of its manuals, please contact Anritsu Company to

confirm whether or not these items are export-controlled.

When disposing of export-controlled items, the products and manuals need to be broken or

shredded to such a degree that they cannot be unlawfully used for military purposes.

MT8860B Safety-1

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu

Company uses the following symbols to indicate safety-related information. For your own

safety, please read the information carefully before operating the equipment.

Symbols Used in Manuals

Safety Symbols Used on Equipment and in Manuals

The following safety symbols are used inside or on the equipment near operation locations to

provide information about safety items and operation precautions. Ensure that you clearly

understand the meanings of the symbols and take the necessary precautions before operating

the equipment. Some or all of the following five symbols may or may not be used on all

Anritsu equipment. In addition, there may be other labels attached to products that are not

shown in the diagrams in this manual.

Danger

This indicates a very dangerous procedure that could result in serious injury

or death, or loss related to equipment malfunction, if not performed properly.

Warning This indicates a hazardous procedure that could result in light-to-severe

injury or loss related to equipment malfunction, if proper precautions are not

taken.

Caution

This indicates a hazardous procedure that could result in loss related to

equipment malfunction if proper precautions are not taken.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates a compulsory safety precaution. The required operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically

in or near the triangle.

Safety-2 MT8860B

For Safety

This indicates a note. The contents are described in the box.

This indicates that the marked part should be recycled.

Warning Always refer to the operation manual when working near locations at

which the alert mark, shown on the left, is attached. There is a risk of

personal injury if operations are performed without heeding the

advice in the operation manual. In addition, the equipment

performance may be reduced. Moreover this alert mark is sometimes

used with other marks and descriptions indicating other dangers.

Warning

When supplying power to this equipment connect the accessory 3-pin

power cord to a 3-pin grounded power outlet. If a grounded 3-pin

outlet is not available use a conversion adapter and ground the green

wire, or connect the frame ground on the rear panel of the equipment

to ground. If power is supplied without grounding the equipment,

there is a risk of receiving a severe or fatal electric shock.

Warning

This equipment can not be repaired by the operator. Do not attempt to

remove the equipment covers or to disassemble internal

components. Only qualified service technicians with a knowledge of

electrical fire and shock hazards should service this equipment.

There are high-voltage parts in this equipment presenting a risk of

severe injury or fatal electric shock to untrained personnel. In

addition, there is a risk of damage to precision components.

MT8860B Safety-3

Caution

Electrostatic Discharge (ESD) can damage the highly sensitive

circuits in the instrument. ESD is most likely to occur as test devices

are being connected to, or disconnected from, the instrument’s front

and rear panel ports and connectors. You can protect the instrument

and test devices by wearing a static-discharge wristband.

Alternatively you can ground yourself to discharge any static charge

by touching the outer chassis of the grounded instrument before

touching the instrument’s front and rear panel ports and connectors.

Avoid touching the test port center conductors unless you are

properly grounded and have eliminated the possibility of static

discharge.

Repair of damage that is found to be caused by electrostatic

discharge is not covered under warranty.

Tabla de contenidos

Otros manuales de Equipo de prueba de Anritsu

Anritsu

Anritsu ML8720B Manual de usuario

Anritsu

Anritsu 691 B Series Manual de usuario

Anritsu

Anritsu MT8850A Manual de usuario

Anritsu

Anritsu Site Master S251B Manual de usuario

Anritsu

Anritsu Site Master S112 Manual de usuario

Anritsu

Anritsu Site Master S113B Manual de usuario

Anritsu

Anritsu MN469xC Series Manual de usuario

Anritsu

Anritsu Network Master Series Manual de usuario

Anritsu

Anritsu VectorStar MN469 C Series Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu BERTWave MP2100B Manual de usuario

Anritsu

Anritsu 681XXC Manual de usuario

Anritsu

Anritsu MT8852B Manual del propietario

Anritsu

Anritsu MG3681A Manual de usuario

Anritsu

Anritsu MT8870A Manual de usuario

Anritsu

Anritsu MT8852A Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu 3656B W1 Manual de usuario

Anritsu

Anritsu 693 B Series Manual de usuario

Anritsu

Anritsu MS8608A Manual de usuario

Anritsu

Anritsu SQA-R MP1900A Manual de referencia

Anritsu

Anritsu MP2110A BERTWave Manual de usuario

Anritsu

Anritsu Precision AutoCal 36585 Series Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario