Anritsu MX183000A Manual de usuario

Document No.: M-W3813AE-4.0

ANRITSU CORPORATION

MX183000A

High-Speed Serial Data

Test Software

Operation Manual

Fourth Edition

•For safety and warning information, please read this

manual before attempting to use the equipment.

•

Additional safety and warning information is provided

in the MP1800A Signal Quality Analyzer

Installation

Guide and the MT1810A 4 Slot Chassis Inst

allation

Guide. Please also refer to one of these documents

before using the equipment.

•

Keep this manual with the equipment.

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of

the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MX183000A

High-Speed Serial Data Test Software

Operation Manual

1 February 2016 (First Edition)

26 October 2016 (Fourth Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

iii

Equipment Certificate

Anritsu Corporation guarantees that this equipment was inspected at

shipment and meets the published specifications.

Anritsu Warranty

•During the warranty period, Anritsu Corporation will repair or exchange this

software free-of-charge if it proves defective when used as described in the

operation manual.

•The warranty period is 6 months from the purchase date.

•The warranty period after repair or exchange will remain 6 months from

the original purchase date, or 30 days from the date of repair or

exchange, depending on whichever is longer.

•This warranty does not cover damage to this software caused by Acts of

God, natural disasters, and misuse or mishandling by the customer.

In addition, this warranty is valid only for the original equipment purchaser. It

is not transferable if the equipment is resold.

Anritsu Corporation shall assume no liability for injury or financial loss of the

customer due to the use of or a failure to be able to use this equipment.

Anritsu Corporation Contact

In the event of this equipment malfunctions, contact an Anritsu Service and

Sales office. Contact information can be found on the last page of the printed

version of this manual, and is available in a separate file on the PDF version.

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country o

f origin for re-

export from your

country.

Before re

exporting the product or manuals, please contact us to confirm

whet

her they are export-controlled items or not.

When you dispose of export

controlled items, the products/manuals need

to be broken/shredded so as not to be unlawfully used for military purpose.

Software End-User License Agreement (EULA)

Please read this Software End-User License Agreement (hereafter this EULA) carefully before using

(includes executing, copying, registering, etc.) this software (includes programs, databases, scenarios,

etc., used to operate, set, etc., Anritsu electronic equipment). By reading this EULA and using this

software, you are agreeing to be bound by the terms of its contents and Anritsu Corporation (hereafter

Anritsu) hereby grants you the right to use this Software with the Anritsu-specified equipment

(hereafter Equipment) for the purposes set out in this EULA.

1. Grant of License and Limitations

1. Regardless of whether this Software was

purchased from or provided free-of-charge by

Anritsu, you agree not to rent, lease, lend, or

otherwise distribute this Software to third

parties and further agree not to disassemble,

recompile, reverse engineer, modify, or

create derivative works of this Software.

2. You may make one copy of this Software for

backup purposes only.

3. You are not permitted to reverse engineer

this software.

4. This EULA allows you to install one copy of

this Software on one piece of Equipment.

2. Disclaimers

To the extent not prohibited by law, in no

event shall Anritsu be liable for personal

injury, or any incidental, special, indirect or

consequential damages whatsoever,

including, without limitation, damages for

loss of profits, loss of data, business

interruption or any other commercial

damages or losses, arising out of or related

to your use or inability to use this Software.

3. Limitation of Liability

a. If a fault (bug) is discovered in this Software,

preventing operation as described in the

operation manual or specifications whether

or not the customer uses this software as

described in the manual, Anritsu shall at its

own discretion, fix the bug, or exchange the

software, or suggest a workaround,

free-of-charge. However, notwithstanding

the above, the following items shall be

excluded from repair and warranty.

i) If this Software is deemed to be used for

purposes not described in the operation

manual or specifications.

ii) If this Software is used in conjunction with

other non-Anritsu-approved software.

iii) Recovery of lost or damaged data.

iv) If this Software or the Equipment has been

modified, repaired, or otherwise altered

without Anritsu's prior approval.

v) For any other reasons out of Anritsu's direct

control and responsibility, such as but not

limited to, natural disasters, software virus

infections, etc.

b. Expenses incurred for transport, hotel, daily

allowance, etc., for on-site repairs by Anritsu

engineers necessitated by the above faults

shall be borne by you.

c. The warranty period for faults listed in

article 3a above covered by this EULA shall

be either 6 months from the date of purchase

of this Software or 30 days after the date of

repair, whichever is longer.

4. Export Restrictions

You may not use or otherwise export or

re-export directly or indirectly this Software

except as authorized by Japanese and

United States law. In particular, this

software may not be exported or re-exported

(a) into any Japanese or US embargoed

countries or (b) to anyone on the Japanese or

US Treasury Department's list of Specially

Designated Nationals or the US Department

of Commerce Denied Persons List or Entity

List. By using this Software, you warrant

that you are not located in any such country

or on any such list. You also agree that you

will not use this Software for any purposes

prohibited by Japanese and US law,

including, without limitation, the

development, design and manufacture or

production of missiles or nuclear, chemical

or biological weapons of mass destruction.

5. Termination

Anritsu shall deem this EULA terminated if

you violate any conditions described herein.

This EULA shall also be terminated if the

conditions herein cannot be continued for

any good reason, such as violation of

copyrights, patents, or other laws and

ordinances.

6. Reparations

If Anritsu suffers any loss, financial or

otherwise, due to your violation of the terms

of this EULA, Anritsu shall have the right to

seek proportional damages from you.

7. Responsibility after Termination

Upon termination of this EULA in

accordance with item 5, you shall cease all

use of this Software immediately and shall

as directed by Anritsu either destroy or

return this Software and any backup copies,

full or partial, to Anritsu.

8. Dispute Resolution

If matters of dispute or items not covered by

this EULA arise, they shall be resolved by

negotiations in good faith between you and

Anritsu.

9. Court of Jurisdiction

This EULA shall be interpreted in

accordance with Japanese law and any

disputes that cannot be resolved by

negotiation described in Article 8 shall be

settled by the Japanese courts.

vii

Before Using VISA*1

For Those Who Use MP1800A

To use the

MX183000A High-Speed Serial Data

Test Software (hereafter

MX183000A

), you are required to install National Instruments™ (

hereafter

™) NI-VISA™*2on the PC controller.

We recommend using

-VISA™*2provided in the USB memory stick

that contains

MX183000A

You are allowed to use

NI-VISA™*2contained in the

USB memory

stick

only for the purpose of using it for MX183000A. Use

-VISA™*2for any other product or purpose is prohibited.

When uninstalling

MX183000A from the PC controller

, uninstall

-VISA™ that was installed from the USB memory stick as well.

Glossary of Terms

*1: VISA: Virtual Instrument Software Architecture

I/O software specification for remote control of measuring

instruments using interfaces such as GPIB, Ethernet, USB, etc.

*2 :NI-VISA™

World de facto standard I/O software interface developed by NI

and standardized by the VXI Plug&Play Alliance.

Trademarks

- National Instruments™, NI™, NI-

VISA™ and National Instruments

Corporation are all trademarks of National Instruments Corporation

viii

Before Using VISA*1

For Those Who Use MT1810A

To use the

MX183000A High-Speed Serial Data Test Softwar

e (hereafter

MX183000A

), you are required to install National Instruments™

(hereafter

™) NI-VISA™*2on the PC controller.

You need to get the

NI-VISA™ Installer yourself.

The USB memory stick

for

MX183000A does not contain

-VISA™ because MT1810A does not include any

NI™

hardware.

Glossary of Terms

*1: VISA: Virtual Instrument Software Architecture

I/O software specification for remote control of measuring

instruments using interfaces such as GPIB, Ethernet, USB, etc.

*2 :NI-VISA™

World de facto

standard I/O software interface developed by NI

and standardized by the VXI Plug&Play Alliance.

Trademarks

- National Instruments™, NI™, NI-

VISA™ and National Instruments

Corporation are all trademarks of National Instruments Corporation

Protection Against Computer Virus Infections

Prior to the software installation

Before installing this software or any other software recommended or

approved by Anritsu,

run

a virus scan on your computer, including

removable media (e.g. USB memory stick and CF memory card) you

want to connect to your computer.

When using this software and connecting with the measuring instrument

•Copying files and data

On your computer, do not save any copies other than the following:

•Files and data provided by Anritsu

•Files created by this software

•Files specified in this document

Before copying these files and/or data, run a virus

scan, including

removable media (e.g. USB memory stick and CF memory card).

•Connecting to network

Connect your computer to the network tha

t provides adequate

protection against computer viruses.

Cautions on Proper Operation of Software

This software may not operate normally if any of the following operations

are performed

on your computer:

•Simultaneously running any software other th

an that recommended or

approved by Anritsu

•Closing the lid (Laptop computer)

•Turning on the screen saver function

•Turning on the battery-power saving function (Laptop computer)

For how to turn off the functions, refer to the

operation manual that cam

with your computer.

CE Conformity Marking

Anritsu affixes the CE Conformity marking on the following product(s) in

accordance with the Decision 768/2008/EC to indicate that they conform to

the EMC and LVD directive of the European Union (EU).

CE marking

1. Product Model

Software: MX183000A High-Speed Serial Data Test Software

2. Applied Directive and Standards

When the MX183000A Jitter/Noise Tolerance Test Software is installed in

the MP1800A or MT1810A, the applied directive and standards of this unit

conform to those of the MP1800A or MT1810A main frame.

PS: About main frame

Please contact Anritsu for the latest information on the main frame

types that MX183000A can be used with.

Tabla de contenidos

Otros manuales de Equipo de prueba de Anritsu

Anritsu

Anritsu MG3641A Manual de usuario

Anritsu

Anritsu MT8852B Manual del propietario

Anritsu

Anritsu BERTWave MP2100B Manual de usuario

Anritsu

Anritsu MT8852A Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu MU150101A Manual de usuario

Anritsu

Anritsu MT9810A Manual de usuario

Anritsu

Anritsu ME7840A Manual de usuario

Anritsu

Anritsu MT8860C Manual de usuario

Anritsu

Anritsu MT8860B Manual del propietario

Anritsu

Anritsu VectorStar MN4690B Series Manual de usuario

Anritsu

Anritsu OSL Series Manual de uso y cuidado

Anritsu

Anritsu Site Master S112 Manual de usuario

Anritsu

Anritsu MP2110A BERTWave Manual de usuario

Anritsu

Anritsu Site Master S251B Manual de usuario

Anritsu

Anritsu MG369 A Series Manual de usuario

Anritsu

Anritsu MP1590B Manual de usuario

Anritsu

Anritsu MD8470A Hoja de especificaciones

Anritsu

Anritsu AutoCal 36581NNF Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu MP1800A Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario