Anritsu InterferenceHunter MA2700A Manual de usuario
User Guide
InterferenceHunter™
MA2700A
Handheld Direction Finding
System
Includes GPS and Electronic Compass
Anritsu Company
490 Jarvis Drive
Morgan Hill, CA 95037-2809
USA
Part Number: 10580-00361
Revision: D
Published: October 2022
Copyright 2013, 2022 Anritsu Company
WARRANTY
The Anritsu product listed on the title page is warranted against defects in materials and
workmanship for one year from the date of shipment.
Anritsu’s obligation covers repairing or replacing products which prove to be defective
during the warranty period. Buyers shall prepay transportation charges for equipment
returned to Anritsu for warranty repairs. Obligation is limited to the original purchaser.
Anritsu is not liable for consequential damages.
LIMITATION OF WARRANTY
The foregoing warranty does not apply to Anritsu connectors that have failed due to
normal wear. Also, the warranty does not apply to defects resulting from improper or
inadequate maintenance, unauthorized modification or misuse, or operation outside of the
environmental specifications of the product. No other warranty is expressed or implied,
and the remedies provided herein are the Buyer’s sole and exclusive remedies.
DISCLAIMER OF WARRANTY
DISCLAIMER OF WARRANTIES. TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, ANRITSU COMPANY AND ITS SUPPLIERS DISCLAIM ALL
WARRANTIES, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, WITH REGARD TO THE PRODUCT. THE USER
ASSUMES THE ENTIRE RISK OF USING THE PRODUCT. ANY LIABILITY OF
PROVIDER OR MANUFACTURER WILL BE LIMITED EXCLUSIVELY TO PRODUCT
REPLACEMENT.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ANRITSU COMPANY OR
ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER
PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THE
PRODUCT, EVEN IF ANRITSU COMPANY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES AND
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
TRADEMARK ACKNOWLEDGMENTS
InterferenceHunter is a trademark of Anritsu Company. All rights reserved.
NOTICE
Anritsu Company has prepared this manual for use by Anritsu Company personnel and
customers as a guide for the proper installation, operation and maintenance of Anritsu
Company equipment and computer programs. The drawings, specifications, and
information contained herein are the property of Anritsu Company, and any unauthorized
use or disclosure of these drawings, specifications, and information is prohibited; they
shall not be reproduced, copied, or used in whole or in part as the basis for manufacture or
sale of the equipment or software programs without the prior written consent of Anritsu
Company.
MA2700A UG PN: 10580-00361 Rev. D Title-3
Notes On Export Management
This product and its manuals may require an Export License or
approval by the government of the product country of origin for
re-export from your country.
Before you export this product or any of its manuals, please contact
Anritsu Company to confirm whether or not these items are
export-controlled.
When disposing of export-controlled items, the products and manuals
need to be broken or shredded to such a degree that they cannot be
unlawfully used for military purposes.
UPDATES
Updates, can be downloaded from the Anritsu Website at:
http://www.anritsu.com/contact-us
Title-4 PN: 10580-00361 Rev. D MA2700A UG
CE Conformity Marking
European Parliament and Council Directive 2012/19/EU
RCM Conformity Marking
UKCA Conformity Marking
Anritsu affixes the CE Conformity marking onto its
conforming products in accordance with Council
Directives of The Council Of The European Communities
in order to indicate that these products conform to the
EMC, LVD, RoHS, and RED directives of the European
Union (EU).
Equipment Marked with the crossed-out Wheelie Bin
symbol complies with the European Parliament and
Council Directive 2012/19/EU (the “WEEE Directive”) in
the European Union.
For Products placed on the EU market after August 13,
2012, please contact your local representative at the end
of the product’s useful life to arrange disposal in
accordance with your initial contract and the local law.
Anritsu affixes the Regulatory Compliance Mark (RCM)
onto its conforming products in accordance with the
electromagnetic compliance regulations of Australia and
New Zealand in order to indicate that these products
conform to the EMC regulations of Australia and New
Zealand.
Anritsu affixes the UKCA Conformity marking onto its
conforming products in accordance with the United
Kingdom conformity assessment body (CAB) in order to
indicate that these products conform to the market of
Great Britain (England, Wales, and Scotland).
MA2700A UG PN: 10580-00361 Rev. D Title-5
KCC Conformity Marking
Recycle Marking
Canadian ICES-001 Conformity Marking
Anritsu affixes the Korean Communications Commissions
(KCC) mark onto its conforming products in accordance
with the electromagnetic compliance regulations of Korea
Anritsu affixes the universal recycle symbol onto its
products to indicate that the marked part is made from
recyclable materials and should be recycled. Materials
should be recycled in accordance with your local
regulatory requirements.
CAN/ICES-1
(A)/NMB-1(A)
Anritsu affixes the CAN ICES-1(A)/NMB-1(A) compliance
label onto its conforming products in accordance with the
following Canadian Interference-Causing Equipment
Standards.
ICES-001 — Industrial, Scientific and Medical (ISM)
Radio Frequency Generators
Title-6 PN: 10580-00361 Rev. D MA2700A UG
Chinese RoHS Compliance Statement
MA2700A UG PN: 10580-00361 Rev. D Safety-1
Safety Symbols
To prevent the risk of personal injury or loss related to product
malfunction, Anritsu Company uses the following symbols to indicate
safety-related information. For your own safety, please read the
information carefully before operating the product.
Symbols Used in Manuals
Danger
This indicates a risk from a very dangerous condition or
procedure that could result in serious injury or death and
possible loss related to product malfunction. Follow all
precautions and procedures to minimize this risk.
Warning This indicates a risk from a hazardous condition or
procedure that could result in light-to-severe injury or
loss related to product malfunction. Follow all
precautions and procedures to minimize this risk.
Caution
This indicates a risk from a hazardous procedure that
could result in loss related to product malfunction.
Follow all precautions and procedures to minimize this
risk.
Safety-2 PN: 10580-00361 Rev. D MA2700A UG
Safety Symbols Used on Product and in Manuals
The following safety symbols are used inside or on the product near
operation locations to provide information about safety items and
operation precautions. Ensure that you clearly understand the
meanings of the symbols and take the necessary precautions before
operating the product. Some or all of the following five symbols may or
may not be used on all Anritsu products. In addition, there may be other
labels attached to products that are not shown in the diagrams in this
manual.
This indicates a prohibited operation. The prohibited
operation is indicated symbolically in or near the barred
circle.
This indicates a compulsory safety precaution. The
required operation is indicated symbolically in or near the
circle.
This indicates a warning or caution. The contents are
indicated symbolically in or near the triangle.
This indicates a note. The contents are described in the
box.
These indicate that the marked part should be recycled.
MA2700A UG PN: 10580-00361 Rev. D Safety-3
For Safety
Danger
Using the MA2700A InterferenceHunter while a
car is in motion could be dangerous and lead to
serious accidents.
Warning
Always refer to the operation manual when
working near locations at which the alert mark,
shown on the left, is attached. If the operation,
etc., is performed without heeding the advice in
the operation manual, there is a risk of personal
injury. In addition, the product performance may
be reduced. Moreover, this alert mark is
sometimes used with other marks and
descriptions indicating other dangers.
Warning
This product can not be repaired by the operator.
Do not attempt to remove the product covers or
to disassemble internal components. Only
qualified service technicians with a knowledge of
electrical fire and shock hazards should service
this product. There are high-voltage parts in this
product presenting a risk of severe injury or fatal
electric shock to untrained personnel. In addition,
there is a risk of damage to precision
components.
Safety-4 PN: 10580-00361 Rev. D MA2700A UG
For Safety
Caution
Electrostatic Discharge (ESD) can damage the
highly sensitive circuits in the instrument. ESD is
most likely to occur as test devices are being
connected to, or disconnected from, the
instrument’s front and rear panel ports and
connectors. You can protect the instrument and
test devices by wearing a static-discharge
wristband. Alternatively, you can ground yourself
to discharge any static charge by touching the
outer chassis of the grounded instrument before
touching the instrument’s front and rear panel
ports and connectors. Avoid touching the test
port center conductors unless you are properly
grounded and have eliminated the possibility of
static discharge.
Repair of damage that is found to be caused by
electrostatic discharge is not covered under
warranty.
Tabla de contenidos
Otros manuales de Equipo de prueba de Anritsu
Anritsu
Anritsu MT9812B Manual de usuario
Anritsu
Anritsu MP8931A Manual de usuario
Anritsu
Anritsu MP1800A Manual de usuario
Anritsu
Anritsu MT1000A Network Master Pro Manual de usuario
Anritsu
Anritsu MT9810A Manual de usuario
Anritsu
Anritsu OSL Series Manual de uso y cuidado
Anritsu
Anritsu 681XXC Manual de usuario
Anritsu
Anritsu ME7840A Manual de usuario
Anritsu
Anritsu MX900030A Manual de usuario
Anritsu
Anritsu MT1000A Network Master Pro Manual de usuario
Anritsu
Anritsu MT1000A Network Master Pro Manual de usuario
Anritsu
Anritsu BERTWave MP2100B Manual de usuario
Anritsu
Anritsu VectorStar MN469 C Series Manual de usuario
Anritsu
Anritsu LMR Master S412E Manual del propietario
Anritsu
Anritsu MT8870A Manual de usuario
Anritsu
Anritsu 3659 Manual de usuario
Anritsu
Anritsu MT1000A Network Master Pro Manual de usuario
Anritsu
Anritsu MX183000A Manual de usuario
Anritsu
Anritsu 693 B Series Manual de usuario
Anritsu
Anritsu MT8860B Manual del propietario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
