Anritsu VectorStar ME7838D Manual de usuario

Quick Start Guide

VectorStar™ME7838D/G

2-Port Broadband/Banded

Millimeter-Wave System

High Performance Modular Broadband/Banded Millimeter-Wave

Vector Network Analyzer (VNA) Measurement System,

70 kHz to 145 GHz (150 GHz) or 70 kHz to 220 GHz (226 GHz)

ME7838D, 70 kHz to 145 GHz (150 GHz)

ME7838G, 70 kHz to 220 GHz (226 GHz)

ME7838D BB/mm-Wave VNA System – MS4647B VNA, 3739C Test Set, MA25300A Modules

ME7838G BB/mm-Wave VNA System – MS4647B VNA, 3739C Test Set, MA25400A Modules

Anritsu Company

490 Jarvis Drive

Morgan Hill, CA 95037-2809

USA

http://www.anritsu.com

Part Number: 10410-00732

Revision: C

Published: January 2020

1. Installing Rear Panel Cables (MS464xA VNA)

QSG-2 PN: 10410-00732 Rev. C VectorStar ME7838D/G QSG

High Performance Modular Broadband/Banded Millimeter-Wave

Vector Network Analyzer (VNA) Measurement System,

70 kHz to 145 GHz or 220 GHz

This guide provides quick setup instructions for the ME7838D/G Broadband/Banded mm-Wave VNA System

assembly. For additional safety and compliance information, and for more details about the assembly,

configuration, setup, and test of the equipment, refer to the VectorStar™ ME7838 Series

Broadband/Millimeter-Wave System Installation Guide – 10410-00293.

This and all other documentation that supports the ME7838D/G is available on the VectorStar product web

page:

http://www.anritsu.com/en-us/products-solutions/products/ms4640b-series.aspx

On this web page, you can select various tabs for more information about your instrument. Included is a

“Library” tab which contains links to all the latest technical documentation related to this instrument.

The ME7838D/G Broadband system consists of the MS4647B VNA with Option 007 (Receiver Offset),

Option 08x (Modular Broadband Connection Capability), the 3739C Broadband Test Set, two MA25300A or

two MA25400A Millimeter-Wave Modules, and the necessary front and rear panel cables. A fully configured

system is shown below.

The ME7838D/G Banded Millimeter-Wave system consists of an MS464xA/B VNA with Option 08x, the 3739C

Broadband Test Set, and two 3744A-EE, 3744A-EW, or two OML/VDI Millimeter-Wave Modules.

1. Installing Rear Panel Cables (MS464xA VNA)

The MS4647A VNA can be used in the ME7838D-based systems only.

This section focuses on installing cables when using a MS464xA VNA. Start the ME7838D assembly by placing

the 3739C Broadband Test Set so you can access the rear panel for cable connection.

Warning To avoid injury, use two or more people to lift the MS464xA VNA to the top of the 3739C Test Set.

Caution

To avoid connector damage or inaccurate measurements, before making any connections, review

the 10100-00060-Connector Care Instruction Sheet. Observe connector torque requirements where

indicated in this guide.

Note The MS4647A software does not support the ME7838G system.

1. Installing Rear Panel Cables (MS464xA VNA)

VectorStar ME7838D/G QSG PN: 10410-00732 Rev. C QSG-3

At the rear panels connect the cables as shown in Figure 1 and Table 1.

Figure 1. Install Rear Panel Cables between 3739C Test Set and MS464xA VNA

WARNING

No operator service-

able parts inside.

Refer servicing to

qualified personnel.

Ext

Alc

Out

Ext

Analog

a1ba2b2

IF Outputs

External I/O

~ LINE INPUT

47-63 Hz

85-240 VAC

150 VA Max

Fuse 250V 2A T

CAUTION

Do not operate with

power cord ungrounded.

CAUTION

For continued fire protection

replace only with specified

type and rated fuse.

Cable Length

Standard Extended

Module Interface

MS464xA VNA

3739C Test Set

b1 IF a2 IF

a1 IF b2 IF

Ext Analog Out Ext ALC External I/O

Ext Analog In

Ext ALC Out

External I/O

Module Interface

Cable Length Switch

1. Installing Rear Panel Cables (MS464xA VNA)

QSG-4 PN: 10410-00732 Rev. C VectorStar ME7838D/G QSG

Table 1. ME78383D Cable Rear Panel Connections (MS464xA VNA)

Part Number Index Description From VNA Location

To 3739C Test Set

Location

MS464xA VNA 1

3739C Test Set 2

73598-1 a

(5 cable bundle)

a. Tighten each cable in this group using an 8 mm (5/16 in) torque end wrench set to 0.9 N·m (8 lbf·in).

3 IF Interface Cables

a1 IF

b1 IF

a2 IF

b2 IF

a1 IF

b1 IF

a2 IF

b2 IF

4 External I/O Cable External I/O External I/O

3-806-225 5 BNC (M-M) Cable VNA Ext Analog Out Test Set Ext Analog In

3-806-225 6 BNC (M-M) Cable VNA Ext ALC Test Set Ext ALC Out

GPIB Cable

(Not supplied) 7Cable for program-

matic control

IEEE 488.2 GPIB (For remote

controlling ME7838) NA

GPIB Cable

(Not supplied) 8Cable for program-

matic control

Dedicated GPIB (For con-

trolling peripherals such as

Power Meter)

Ethernet Cable

(Not supplied) 9

Cable for program-

matic control Ethernet Port NA

USB Type B Cable

(Not supplied)

Cable for program-

matic control USB Port (2) NA

– 10 AC Power Cord AC Power Input NA

– 11 AC Power Cord NA AC Power Input

– 12 Module Interface Cable Length Switch (Included with 3739C-003 Option)

2. Installing Rear Panel Cables (MS464xB VNA)

VectorStar ME7838D/G QSG PN: 10410-00732 Rev. C QSG-5

2. Installing Rear Panel Cables (MS464xB VNA)

This section focuses on installing cables when using a MS464xB VNA. Start the ME7838D/G assembly by

placing the 3739C Broadband Test Set so you can access the rear panel for cable connection.

At the rear panels connect the cables as shown in Figure 2 and Table 2.

Warning To avoid injury, use two or more people to lift the MS464xB VNA to the top of the 3739C Test Set.

Caution

To avoid connector damage or inaccurate measurements, before making any connections, review

the 10100-00060-Connector Care Instruction Sheet, that was shipped with this system. Observe

connector torque requirements where indicated in this guide.

Figure 2. Install Rear Panel Cables between 3739C Test Set and MS464xB VNA

WARNING

No operator service-

able parts inside.

Refer servicing to

qualified personnel.

Ext

Alc

Out

Ext

Analog

a1ba2b2

IF Outputs

External I/O

~ LINE INPUT

47-63 Hz

85-240 VAC

150 VA Max

Fuse 250V 2A T

CAUTION

Do not operate with

power cord ungrounded.

CAUTION

For continued fire protection

replace only with specified

type and rated fuse.

Cable Length

Standard Extended

Module Interface

Ext In ALC 2

(With Option 031)

Ext In ALC 1

(No Option 031)

Module Interface

Cable Length Switch

MS464xB VNA

b1 IF a2 IF

a1 IF b2 IF

Ext Analog Out

External I/O

Ext Analog In

Ext ALC Out

External I/O

333

3739C Test Set

3739C-003 Option Only

2. Installing Rear Panel Cables (MS464xB VNA)

QSG-6 PN: 10410-00732 Rev. C VectorStar ME7838D/G QSG

Table 2. ME78383D/G Cable Rear Panel Connections (MS464xB VNA)

Part Number Index Description From VNA Location

To 3739C Test Set

Location

MS464xB VNA 1

3739C Test Set 2

73598-1 a

(5 cable bundle)

a. Tighten each cable in this group using an 8 mm (5/16 in) torque end wrench set to 0.9 N·m (8 lbf·in).

3 IF Interface Cables

a1 IF

b1 IF

a2 IF

b2 IF

a1 IF

b1 IF

a2 IF

b2 IF

4 External I/O Cableb

b. Tighten the connector screws with a flat blade screwdriver.

External I/O External I/O

3-806-225 5 BNC (M-M) Cable Ext Analog Out Test Set Ext Analog In

3-806-225 6 BNC (M-M) Cable Ext In ALC 1 (without Option 031)

Ext In ALC 2 (with Option 031) Test Set Ext ALC Out

GPIB Cable

(Not supplied) 7Cable for program-

matic control

IEEE 488.2 GPIB (for remote

controlling ME7838) NA

GPIB Cable

(Not supplied) 8Cable for program-

matic control

Dedicated GPIB (For controlling

peripherals such as Power

Meter)

Ethernet Cable

(Not supplied) 9

Cable for program-

matic control Ethernet Port NA

USB Type B Cable

(Not supplied)

Cable for program-

matic control USB Port (2) NA

– 10 AC Power Cordc

c. Do not yet connect to AC power cords to the AC source.

AC Power Input NA

– 11 AC Power CordcNA AC Power Input

– 12 Module Interface Cable Length Switch (Included with 3739C-003 Option)

3. Installing Front Panel Cables

VectorStar ME7838D/G QSG PN: 10410-00732 Rev. C QSG-7

3. Installing Front Panel Cables

Connect the front panel cables between the MS464xA/B VNA and the 3739C Test Set, and between the Test

Set and the millimeter-Wave modules as shown in Figure 3 and as described in Table 3.

Example MS464xA/B VNA equipped with Option 051, 061, or 062 with included Front Panel Loops

Note: The cables for Test Port 1 to Module SRC (key 8 to 9) and Test Port 2 to Module SRC (key 12 to13) are not

used with mm-Wave modules 3744A-EE, 3744A-EW, or 3744A-Rx.

Figure 3. Front Panel Cables between 3739C Test Set, MS464xA/B VNA, and Modules

+27 dBm MAX AVOID STATIC DISCHARGE

ALL PORTS: CAUTION

Standby Operate

Frequency

Power

Sweep

Avg

Response

Display

Scale

Marker

Channel

Trace

Measurement

Calibration

Application

File

System

Help

Preset

RF, LO, Test, Ref,

and Pwr/Signal to

Port 1

Module

Test Port 1

to Module SRC

(MA25300A, MA25400A, or 3743A)

Test Port 2

to Module SRC

(MA25300A, MA25400A, or 3743A)

RF, LO, Test, Ref,

and Pwr/Signal to

Port 2

Module

3. Installing Front Panel Cables

QSG-8 PN: 10410-00732 Rev. C VectorStar ME7838D/G QSG

Table 3. ME78383D/G Cable Interconnect Part Numbers and Locations

Part Number Index Description

Connection

From

Connection

MS464xA/B 1 VectorStar VNA – –

3739C 2 3739C Broadband Test Set – –

67357-xx

(See Note 1)

3 Semi-Rigid (KM-KM) Cable

• Tighten using an 8 mm (5/16 in) torque end

wrench set to 0.9 N·m (8 lbf·in).

VNA RF Test Set RF

67357-xx

(See Note 1)

4 Semi-Rigid (KM-KM) Cable

• Tighten using an 8 mm (5/16 in) torque end

wrench set to 0.9 N·m (8 lbf·in).

VNA LO1 Test Set LO1

67357-xx

(See Note 1)

5 Semi-Rigid (KM-KM) Cable

• Tighten using an 8 mm (5/16 in) torque end

wrench set to 0.9 N·m (8 lbf·in).

VNA LO2 Test Set LO2

75685-1

6-7,

10-11

mm-Wave Module Interface Cables

(for MA25300A, MA25400A, 3743A,

3744A-EE, 3744A-EW modules)

Group of 5 cables for each port

Test Set

(Port 1, Port 2)

RF, LO, Test, Ref,

Power/Signal

Module

(Port 1, Port 2)

RF, LO, Test, Ref,

Power/Signal

75685-2

OML Module Interface Cables

Group of 4 cables for each port

Test Set

(Port 1, Port 2)

RF, LO, Test, Ref

Module

(Port 1, Port 2)

RF, LO, Test IF,

Ref IF

VDI Module Interface Cables

Group of 4 cables for each port

Test Set

(Port 1, Port 2)

RF, LO, Test, Ref

Module

(Port 1, Port 2)

RF Input, LO

Input, Meas. IF,

Ref IF

75685-3

mm-Wave Module Interface Cables

(for 3744A-Rx modules)

Group of 3 cables

Test Set

(Port 1, Port 2)

LO, Test,

Power/Signal

Module

(Port 1, Port 2)

LO, Test,

Power/Signal

806-xxx-R a

(See Note 2)

8-9,

12-13

Coaxial Cable

(MA25300A, MA25400A, or 3743A modules)

VNA

(Port 1, Port 2)

mmWave module

(Port 1, Port 2)

Cable Selection Notes

Note 1

Cable Selection Description

67357-13 Standard

(Non-Rack Mount) –

67357-67 3739C-001 Rack

Mount Option –

Note 2

Cable Selection Description

806-206-R 24 in, 1.85 mm

M-F coaxial cable –

806-209-R 36 in, 1.85 mm

M-F coaxial cable –

806-396-R

36 in, 1.85 mm

M-F phase stable

coaxial cable

–

3. Installing Front Panel Cables

VectorStar ME7838D/G QSG PN: 10410-00732 Rev. C QSG-9

a. The 806-xxx-R Coaxial Cables are not included or required when using the 3744A-EE, 3744A-EW mm-Wave modules, or the

3744A-Rx Receiver Module.

4. Millimeter-Wave Module Connections

QSG-10 PN: 10410-00732 Rev. C VectorStar ME7838D/G QSG

4. Millimeter-Wave Module Connections

Connect the 3739C Broadband Test Set Port-1 and Port-2 cables to the MA25300A, MA25400A, 3743A,

3744A-EE, 3744A-EW, or 3744A-Rx Modules as shown in Figure 4 and Figure 5, observing the correct torque

limits for each connector, as specified in Table 4. Route the cable assemblies through the cable restraint.

Note

For ease of connection, the module can be removed from the bracket, then reinstalled after cables

are secured. Observe torque instructions where indicated.

Each module (except the 3744A-Rx) is characterized for absolute power for a specific VNA Serial

Number and VNA Test Port as designated on the module port assignment label. Ensure the module

matches the correct VNA and Test Set port.

If an alternative MA25300A or 3743 series mm-Wave module is used there will be approximately

1 dB of absolute power inaccuracy, which can be corrected by performing a power calibration.

An alternative MA25400A mm-wave module can lead to a 3 dB absolute power accuracy at higher

frequencies which can also be corrected by performing a power calibration.

For more detailed information on the modules including DUT Waveguide (WG) connection alignment

and custom bracket mounting, refer to 10410-00311-VectorStar® Broadband/Banded

Millimeter-Wave Modules Reference Manual.

Figure 4. Millimeter-Wave Module Connections—374x Modules

TEST

Power/Signal

REF

SRC (Not used)

3744A-EE

3744A-EW

3743A

TEST REF

SRC

Power/Signal

LO 6

3743A

TEST REF

SRC

Power/Signal

(Not used)

3744A-Rx

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Anritsu

Anritsu

Anritsu Site Master S332D Manual de usuario

Anritsu

Anritsu MT8801C Manual de usuario

Anritsu

Anritsu VectorStar MS4640A Series Manual de usuario

Anritsu

Anritsu Field Master Pro Manual de usuario

Anritsu

Anritsu Field Master Pro MS2090A Manual del propietario

Anritsu

Anritsu LMR Master Manual de usuario

Anritsu

Anritsu Site Master S331D Manual del propietario

Anritsu

Anritsu FieldMaster MS2080A Manual de usuario

Anritsu

Anritsu Field Master Pro MS2090A Manual de usuario

Anritsu

Anritsu MU196060A Manual de usuario

Anritsu

Anritsu Power Master MA24507A Manual de usuario

Anritsu

Anritsu VectorStar ME7848E Series Manual de usuario

Anritsu

Anritsu Site Master S331C Manual de usuario

Anritsu

Anritsu Spectrum Master MS2711E Manual de usuario

Anritsu

Anritsu Series MS278XB Manual de usuario

Anritsu

Anritsu 11 Series Instrucciones de funcionamiento

Anritsu

Anritsu MS2830A Manual de usuario

Anritsu

Anritsu VNA Master MS203 A Series Manual de usuario

Anritsu

Anritsu Field Master MS2080A Manual de usuario

Anritsu

Anritsu MP1763C Manual de usuario

Anritsu

Anritsu MS2722C Manual de usuario

Anritsu

Anritsu VectorStar ME7838E4 Manual de usuario

Anritsu

Anritsu Spectrum Master MS2711E Manual de usuario

Anritsu

Anritsu MS2665C Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario