Anritsu MS2665C Manual de usuario

The test & measurement

equipment you need at

the price you want.

Alltest carries the world’s largest selection of

used/refurbished benchtop test & measurement

equipment at 50% the price of new.

Our equipment is guaranteed working, warrantied, and

available with certified calibration from our in-house staff

of technicians and engineers.

• 10+ full time technicians with over 150 years of

specialization

• 90 day warranty & 5 day right of return on all

equipment

•

• 1-3 year warranties for new and

premium-refurbished equipment

• Every unit tested to OEM specifications

• Satisfaction guaranteed

You have plans, we will help you achieve them.

Any project. Any budget.

Get a quote today!

CCall (732) 919-3339 or email sales@alltest.net.

Alltest Instruments, Inc.

500 Central Ave.

Farmingdale, NJ 07727

P: (732) 919-3339

F: (732) 919-3332

alltest.net

sales@alltest.net

Document No.: M-W1335AE-15.0

ANRITSU CORPORATION

MS2665C/67C/68C

Spectrum Analyzer

Operation Manual

Vol. 1

(Basic Operating Instructions)

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

15th Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following

safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the

symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols

and take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MS2665C/67C/68C

Spectrum Analyzer

Operation Manual Vol. 1 (Basic Operating Instructions)

28 November 1997 (First Edition)

12 December 2007 (15th Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

WARNING

1. ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the

left may also be used with other marks and descriptions to indicate

other dangers.

2. IEC 61010 Standard

The IEC 61010 standard specifies four categories to ensure that an

instrument is used only at locations where it is safe to make

measurements. This instrument is designed for measurement

category I (CAT I). DO NOT use this instrument at locations

specified as category II, III, or IV as defined below.

Measurement category I (CAT I):

Secondary circuits of a device that is not directly connected to a

power outlet.

Measurement category II (CAT II):

Primary circuits of a device that is directly connected to a power outlet,

e.g., portable tools or home appliance.

Measurement category III (CAT III):

Primary circuits of a device (fixed equipment) to which power is

supplied directly from the distribution panel, and circuits running from

the distribution panel to power outlet.

Measurement category IV (CAT IV):

Building service-line entrance circuits, and circuits running from the

service-line entrance to the meter or primary circuit breaker

(distribution panel).

3. To ensure that the instrument is earthed, always use the supplied 3-

pin power cord, and insert the plug into an outlet with an earth

terminal. If power is supplied without earthing the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

Electric Shock

For Safety

WARNING

4. This equipment cannot be repaired by the operator. DO NOT attempt

to remove the equipment covers or unit covers or to disassemble

internal components. Only qualified service personnel with a

knowledge of electrical fire and shock hazards should service this

equipment. There are high-voltage parts in this equipment presenting

a risk of severe injury or fatal electric shock to untrained personnel. In

addition, there is a risk of damage to precision components.

5. The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu service

personnel, or service personnel of an Anritsu sales representative,

should break this seal to repair or calibrate the equipment. If the

performance-guarantee seal is broken by you or a third party, the

performance of the equipment cannot be guaranteed. Be careful not

to break the seal by opening the equipment or unit covers.

6. This equipment should always be positioned in the correct manner.

If the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

7. DO NOT short the battery terminals and never attempt to disassemble

the battery or dispose of it in a fire. If the battery is damaged by any of

these actions, the battery fluid may leak. This fluid is poisonous.

DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is

accidentally ingested, spit it out immediately, rinse your mouth with

water and seek medical help. If it enters your eyes accidentally, do

not rub your eyes, rinse them with clean running water and seek

medical help. If the liquid gets on your skin or clothes, wash it off

carefully and thoroughly.

8. This instrument uses a Liquid Crystal Display (LCD). DO NOT subject

the instrument to excessive force or drop it. If the LCD is subjected to

strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested

accidentally, spit it out immediately, rinse your mouth with water and

seek medical help. If it enters your eyes accidentally, do not rub

your eyes, rinse them with clean running water and seek medical help.

If the liquid gets on your skin or clothes, wash it off carefully and

thoroughly.

Repair

Falling Over

Battery Fluid

LCD

Calibration

For Safety

CAUTION

1. Always remove the mains power cable from the power outlet before

replacing blown fuses. There is a risk of electric shock if fuses are

replaced with the power cable connected. Always use new fuses of

the type and rating specified on the rear panel of the instrument.

There is a risk of fire if a fuse of a different rating is used.

T5A indicates a time-lag fuse.

2. Keep the power supply and cooling fan free of dust.

•Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

•Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

3. Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

• Maximum DC voltage ratings:

RF Input DC 0 V

• Maximum AC power ratings:

RF Input +30 dBm

• NEVER input a >+30 dBm and >DC 0 V power to RF Input.

• Excessive power may damage the internal circuits.

Fuse Replacement

Cleaning

Check Terminal

For Safety

CAUTION

This equipment uses a Poly-carbomonofluoride lithium battery to backup

the memory. This battery must be replaced by service personnel when

it has reached the end of its useful life; contact the Anritsu sales section

or your nearest representative.

Note: The battery used in this equipment has a maximum useful life of

7 years. It should be replaced before this period has elapsed.

This equipment uses memory cards as external storage media for

storing data and programs.

If this media is mishandled or becomes faulty, important data may be lost.

To prevent this chance occurrence, all important data and programs

should be backed-up.

Anritsu will not be held responsible for lost data.

Pay careful attention to the following points.

•Never remove the memory card from the instrument while it is being

accessed.

•The memory card may be damaged by static electric charges.

•The back-up battery in SRAM memory cards has a finite life.

Replace the battery periodically. For details, refer to the explanation

on the memory card later in this manual.

•Anritsu has thoroughly tested all external storage media shipped with

this instrument. Users should note that external storage media not

shipped with this instrument may not have been tested by Anritsu, thus

Anritsu cannot guarantee the performance or suitability of such media.

This instrument is designed for an industrial environment.

In a residential environment this instrument may cause radio interference

in which case the user may be required to take adequate measures.

Replacing Memory

Back-up Battery

External

Storage Media

Use in a residential

environment

vii

Equipment Certificate

Anritsu Corporation certifies that this equipment was tested before

shipment using calibrated measuring instruments with direct traceability

to public testing organizations recognized by national research

laboratories, including the National Institute of Advanced Industrial

Science and Technology, and the National Institute of Information and

Communications Technology, and was found to meet the published

specifications.

Anritsu Warranty

Anritsu Corporation will repair this equipment free-of-charge if a

malfunction occurs within one year after shipment due to a manufacturing

fault, under the condition that this warranty is void when:

•The fault is outside the scope of the warranty conditions described in

the operation manual.

•The fault is due to mishandling, misuse, or unauthorized modification

or repair of the equipment by the customer.

•The fault is due to severe usage clearly exceeding normal usage.

•The fault is due to improper or insufficient maintenance by the

customer.

•The fault is due to natural disaster including fire, flooding, earthquake,

etc.

•The fault is due to use of non-specified peripheral equipment,

peripheral parts, consumables, etc.

•The fault is due to use of a non-specified power supply or in a non-

specified installation location.

In addition, this warranty is valid only for the original equipment

purchaser. It is not transferable if the equipment is resold.

Anritsu Corporation shall assume no liability for injury or financial loss of

the customer due to the use of or a failure to be able to use this equipment.

Anritsu Corporation Contact

In the event that this equipment malfunctions, contact an Anritsu Service

and Sales office. Contact information can be found on the last page of

the printed version of this manual, and is available in a separate file on

the CD version.

viii

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country of origin for re-export from you

country.

Before re-exporting the product or manuals, please contact us to confirm

whether they are export-controlled items or not.

When you dispose of export-controlled items, the products/manuals need

to be broken/shredded so as not to be unlawfully used for military purpose.

Crossed-out Wheeled Bin Symbol

Equipment marked with the Crossed-out Wheeled Bin Symbol complies

with council directive 2002/96/EC (the “WEEE Directive”) in European

Union.

For Products placed on the EU market after August 13, 2005, please

contact your local Anritsu representative at the end of the product's

useful life to arrange disposal in accordance with your initial contract and

the local law.

Otros manuales para MS2665C

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Anritsu

Anritsu

Anritsu 37 D Series Manual de usuario

Anritsu

Anritsu Site Master S113BQ Manual de usuario

Anritsu

Anritsu MU181500B Manual de usuario

Anritsu

Anritsu VNA Master MS2026C Manual del propietario

Anritsu

Anritsu VectorStar ME7838G4 Manual de usuario

Anritsu

Anritsu HA-100 Series Manual de usuario

Anritsu

Anritsu VNA Master MS2026C Manual de usuario

Anritsu

Anritsu MT8212E Manual de usuario

Anritsu

Anritsu Network Data Analyzer MD6430A Manual de usuario

Anritsu

Anritsu ms9710b Manual de usuario

Anritsu

Anritsu MS2690A Manual de usuario

Anritsu

Anritsu Spectrum Master MS2711E Manual de usuario

Anritsu

Anritsu VNA master Manual de usuario

Anritsu

Anritsu MT1000A Network Master Pro Manual de usuario

Anritsu

Anritsu MS2711B Manual de usuario

Anritsu

Anritsu MT8852B Manual de usuario

Anritsu

Anritsu CMA50 Manual de usuario

Anritsu

Anritsu PowerMaster MA245 A Series Manual de usuario

Anritsu

Anritsu MS2681A Manual de usuario

Anritsu

Anritsu 11 Series Instrucciones de funcionamiento

Anritsu

Anritsu MS9710C Manual de usuario

Anritsu

Anritsu MX269017A Manual de usuario

Anritsu

Anritsu MP1763C Manual de usuario

Anritsu

Anritsu MS2690A Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario