Anritsu MS2691A Manual de usuario

Document No.: M-W2852AE-30.0

ANRITSU CORPORATION

●For safety and warning information, please read this

manual before attempting to use the equipment.

●

Additional safety and warning information is provided

within the MS2690A/MS2691A/MS2692A Signal

Analyzer Operation Manual (Mainframe Operation).

Please also refer to this document before using the

equipment.

●

Keep this manual with the equipment.

MS2690A/MS2691A/MS2692A

Signal Analyzer

Operation Manual

Signal Analyzer Function

Operation

30th Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following

safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the

symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu equipment.

In addition, there may be other labels attached to products that are not shown in the diagrams in this manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is indicated

symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MS2690A/MS2691A/MS2692A

Signal Analyzer

Operation Manual Signal Analyzer Function Operation

24 April 2007 (First Edition)

30 October 2017 (30th Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

iii

Notes On Export Management

This product and its manuals may require an Export License/Approval by

the Government of the product's country

of origin for re-

export from your

country.

Before re

exporting the product or manuals, please contact us to confirm

whet

her they are export-controlled items or not.

When you dispose of export

controlled items, the products/manuals need to

be broken/shredded so as not to be unlawfully used for military purpose.

Cautions Against Computer Virus Infection

●

Copying files and data

Only files that have been provided directly from Anritsu or generated

using Anritsu equipment should be copied to the instrument.

All other required files should be transferred by means of USB or

CompactFlash media after undergoing a thorough virus check.

●

Adding software

Do not download or install software that has not been specifically

recommended or licensed by Anritsu.

●

Network connections

Ensure that the network has sufficient anti-

virus security protection in

place.

About This Manual

Operation manual configuration

The operation manual configuration of the MS2690A/MS2691A/MS2692A

Signal Analyzer is shown below.

MS2690A/MS2691A/MS2692A Signal Analyzer Operation Manual

(

Main Frame O

eration

)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A

Signal Analyzer Operation Manual (Phase Noise Measurement Function Operation)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A

Signal Analyzer Operation Manual (Phase Noise Measurement Function Remote Control)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A

Signal Analyzer Operation Manual (Main Frame Remote Control)

MS2850A Signal Analyzer Operation Manual (Main Frame Operation)

MS2830A Signal Analyzer Operation Manual (Main Frame Operation)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A

Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control)

MS2830A/MS2840A/MS2850A

Signal Analyzer Operation Manual

(Signal Analyzer Function Operation)

MS2690A/MS2691A/MS2692A

Spectrum Analyzer Operation Manual

(Spectrum Analyzer Function Operation)

MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A

Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control)

MS2830A/MS2840A/MS2850A

Spectrum Analyzer Operation Manual

(Spectrum Analyzer Function Operation)

MS2840A Signal Analyzer Operation Manual (Main Frame Operation)

MS2690A/MS2691A/MS2692A

Signal Analyzer Operation Manual

(Signal Analyzer Function Operation)

Signal Analyzer Operation Manual (Mainframe Operation)

Signal Analyzer Operation Manual (Mainframe Remote Control)

Description of basic operations, maintenance procedures, common

functions and common remote functions of the mainframe

Signal Analyzer Operation Manual (Signal Analyzer Function Operation)

Signal Analyzer Operation Manual (Signal Analyzer Function Remote

Control)

Description of basic operations, functions and remote functions of the

signal analyzer

Signal Analyzer Operation Manual (Spectrum Analyzer Function

Operation)

Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote

Control)

Description of basic operations, functions and remote functions of the

spectrum analyzer

Signal Analyzer Operation Manual (Phase Noise Measurement Function

Operation)

Signal Analyzer Operation Manual (Phase Noise Measurement Function

Remote Control)

Description of basic operations, functions and remote functions of the

phase noise measurement function.

In this document, indicates a panel key.

III

Appendix Index

Table of Contents

About This Manual........................................ I

Chapter 1 Overview ........................................... 1-1

1.1 Overview of Signal Analyzer......................................... 1-2

1.2 Features of Signal Analyzer.......................................... 1-3

Chapter 2 Basic Operation................................ 2-1

2.1 Display Description ....................................................... 2-2

2.2 Setting Frequency......................................................... 2-4

2.3 Setting Level ............................................................... 2-15

2.4 Setting IQ Data Capture Time Range......................... 2-31

Chapter 3 Selecting Waveform Capture

Method............................................ 3-1

3.1 Single/Continuous Measurement.................................. 3-2

3.2 Trigger Function............................................................ 3-3

Chapter 4 Trace ................................................. 4-1

4.1 Selecting Trace............................................................. 4-3

4.2 Spectrum....................................................................... 4-5

4.3 Power vs Time ............................................................ 4-71

4.4 Frequency vs Time ................................................... 4-118

4.5 Phase vs Time .......................................................... 4-157

4.6 CCDF ........................................................................ 4-175

4.7 Spectrogram ............................................................. 4-200

4.8 No Trace ................................................................... 4-221

4.9 Sub-Trace ................................................................. 4-227

Chapter 5 Digitize Function .............................. 5-1

5.1 Saving IQ Data.............................................................. 5-2

5.2 Replay Function.......................................................... 5-10

5.3 Playback Function ...................................................... 5-18

IV.

Chapter 6 System Setting ................................. 6-1

6.1 Setting System.............................................................. 6-2

6.2 Erasing Warm up Message .......................................... 6-3

6.3 Setting Title ................................................................... 6-4

6.4 Adjusting Internal Reference Clock Signal ................... 6-5

6.5 Input Source for Reference Clock Signal ..................... 6-6

6.6 Pre-Amp On/Off Display ............................................... 6-7

6.7 Setting Preselector ....................................................... 6-8

Chapter 7 Setting DigRF 3G.............................. 7-1

7.1 Display Description ....................................................... 7-2

7.2 Setting Input.................................................................. 7-3

7.3 Setting Frequency......................................................... 7-8

7.4 Setting Level ................................................................. 7-9

7.5 Setting IQ Data Capture Time Range......................... 7-11

7.6 Trigger Function.......................................................... 7-14

7.7 Selecting Trace........................................................... 7-16

7.8 Saving IQ Data............................................................ 7-36

7.9 System Setting............................................................ 7-40

7.10 Default Value List........................................................ 7-42

Appendix A Error Messages....................... A-1

Appendix B Default Value List ................... B-1

Appendix C Standard Parameter List ........ C-1

Appendix D FFT and RBW .......................... D-1

Appendix E IQ Data Time Actually Required.. E-1

Appendix F Saving Waveform CSV DATA F-1

Index .......................................................... Index-1

1-1

Overview

Chapter 1

Overview

This chapter describes an overview of the Signal Analyzer function.

1.1 Overview of Signal Analyzer......................................... 1-2

1.2 Features of Signal Analyzer.......................................... 1-3

Chapter 1 Overview

1-2

1.1 Overview of Signal Analyzer

The MS2690A/MS2691A/MS2692A Signal Analyzer (hereinafter, referred

to as “MS2690A/MS2691A/MS2692A”) can measure the transmitter

characteristics of wireless devices for various types of mobile

communications quickly, accurately, and easily.

The Signal Analyzer function can achieve high-speed spectrum analysis

and simultaneous analysis on the frequency and time axes, which cannot

be achieved by a conventional sweep type spectrum analyzer, by using

FFT processing (fast Fourier transformation). Also, it can record the RF

input signal as digital data (digitize function).

The Signal Analyzer function has the following features:

•Broad frequency band (6 GHz/13.5 GHz/26.5 GHz)

•Broad analysis bandwidth (31.25 MHz/62.5 MHz*1/125 MHz*2)

•Continuous analysis of captured data is available

•High-capacity waveform memory is installed

•High-speed spectrum analysis is available

•Wide variety of measurement functions

These characteristics enable the MS2690A/MS2691A/MS2692A to be

used for various applications, from research and development to

manufacturing.

*1: 62.5 MHz can be set only when Option 078 Analysis Bandwidth

(hereafter, Option 078) is installed.

*2: 125 MHz can be set only when Option 004 Wideband Analysis

Hardware or Option 078 Analysis Bandwidth (hereafter, Option 078) is

installed.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Anritsu

Anritsu

Anritsu MU196020A PAM4 PPG Manual de usuario

Anritsu

Anritsu Spectrum Master MS2711D Manual del propietario

Anritsu

Anritsu MP1570A Manual de usuario

Anritsu

Anritsu Spectrum Master MS2711E Manual de usuario

Anritsu

Anritsu Network Master MT9090A Series Manual de usuario

Anritsu

Anritsu LMR Master S412E Manual de usuario

Anritsu

Anritsu MS2665C Manual de usuario

Anritsu

Anritsu VectorStar ME7848A Series Manual de usuario

Anritsu

Anritsu Spectrum Master MS2711D Manual de usuario

Anritsu

Anritsu VNA Master MS202 B Series Manual de usuario

Anritsu

Anritsu Spectrum Master MS2721B Manual de usuario

Anritsu

Anritsu MS2665C Manual de usuario

Anritsu

Anritsu VectorStar ME7848E Series Manual de usuario

Anritsu

Anritsu MS2690A Manual de instalación

Anritsu

Anritsu MD1230A Manual de usuario

Anritsu

Anritsu Field Master Pro Manual de usuario

Anritsu

Anritsu MS2830A Manual de usuario

Anritsu

Anritsu ms2602a Manual de usuario

Anritsu

Anritsu FieldMaster MS2080A Manual de usuario

Anritsu

Anritsu VectorStar ME7838D Manual de usuario

Anritsu

Anritsu ShockLine ME7868A Manual de usuario

Anritsu

Anritsu VectorStar ME7828A Series Manual de usuario

Anritsu

Anritsu VNA Master MS2026C Manual de usuario

Anritsu

Anritsu MT8801C Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario