Anritsu MS2690A Manual de usuario
Document No.: M-W3655AE-1.0
ANRITSU CORPORATION
MS2690A/MS2691A/MS2692A
and MS2830A
Signal Analyzer
Operation Manual
Noise Figure Measurement Function
Operation
First Edition
•
For safety and warning information, please read this
manual before attempting to use the equipment.
•
Additional safety and warning information is
provided within the MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Mainframe
Operation) or MS2830
A Signal Analyzer Operation
Manual (Mainframe Operation). Please also refer
to
this document before using the equipment.
•
Keep this manual with the equipment.
ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the
following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of
the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu
equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this
manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and
take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer
Operation Manual Noise Figure Measurement Function Operation
23 October 2012 (First Edition)
Copyright © 2012, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION
iii
Equipment Certificate
Anritsu Corporation guarantees that this equipment was inspected at
shipment and meets the published specifications.
Anritsu Warranty
•During the warranty period, Anritsu Corporation will repair or exchange this
software free-of-charge if it proves defective when used as described in the
operation manual.
•The warranty period is 6 months from the purchase date.
•The warranty period after repair or exchange will remain 6 months from
the original purchase date, or 30 days from the date of repair or
exchange, depending on whichever is longer.
•This warranty does not cover damage to this software caused by Acts of
God, natural disasters, and misuse or mishandling by the customer.
In addition, this warranty is valid only for the original equipment purchaser. It
is not transferable if the equipment is resold.
Anritsu Corporation shall assume no liability for injury or financial loss of the
customer due to the use of or a failure to be able to use this equipment.
Anritsu Corporation Contact
In the event that this equipment malfunctions, contact an Anritsu Service and
Sales office. Contact information can be found on the last page of the printed
version of this manual, and is available in a separate file on the CD version.
iv
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re
-
export from your
country.
Bef
ore re-
exporting the product or manuals, please contact us to confirm
whet
her they are export-controlled items or not.
When you dispose of export
-
controlled items, the products/manuals need
to be broken/shredded so as not to be unlawfully used for military purpose.
Cautions against computer virus infection
•Copying files and data
Only files that have been provided directly from Anritsu or generated
using Anritsu equipment should be copied to the instrument.
All other required files should be transf
erred by means of USB or
CompactFlash media after undergoing a thorough virus check.
•Adding software
Do not download or install software that has not been specifically
recommended or licensed by Anritsu.
•Network connections
Ensure that the network has sufficient anti-
virus security protection in
place
.
v
Software End-User License Agreement (EULA)
Please read this Software End-User License Agreement (hereafter this EULA) carefully before using
(includes executing, copying, registering, etc.) this software (includes programs, databases, scenarios,
etc., used to operate, set, etc., Anritsu electronic equipment). By reading this EULA and using this
software, you are agreeing to be bound by the terms of its contents and Anritsu Corporation (hereafter
Anritsu) hereby grants you the right to use this Software with the Anritsu-specified equipment
(hereafter Equipment) for the purposes set out in this EULA.
1. Grant of License and Limitations
1. Regardless of whether this Software was
purchased from or provided free-of-charge by
Anritsu, you agree not to rent, lease, lend, or
otherwise distribute this Software to third
parties and further agree not to disassemble,
recompile, reverse engineer, modify, or create
derivative works of this Software.
2. You may make one copy of this Software for
backup purposes only.
3. You are not permitted to reverse engineer
this software.
4. This EULA allows you to install one copy of
this Software on one piece of Equipment.
2. Disclaimers
To the extent not prohibited by law, in no
event shall Anritsu be liable for personal
injury, or any incidental, special, indirect or
consequential damages whatsoever,
including, without limitation, damages for
loss of profits, loss of data, business
interruption or any other commercial
damages or losses, arising out of or related
to your use or inability to use this Software.
3. Limitation of Liability
a. If a fault (bug) is discovered in this Software,
preventing operation as described in the
operation manual or specifications whether
or not the customer uses this software as
described in the manual, Anritsu shall at its
own discretion, fix the bug, or exchange the
software, or suggest a workaround,
free-of-charge. However, notwithstanding
the above, the following items shall be
excluded from repair and warranty.
i) If this Software is deemed to be used for
purposes not described in the operation
manual or specifications.
ii) If this Software is used in conjunction with
other non-Anritsu-approved software.
iii) Recovery of lost or damaged data.
iv) If this Software or the Equipment has been
modified, repaired, or otherwise altered
without Anritsu's prior approval.
v) For any other reasons out of Anritsu's direct
control and responsibility, such as but not
limited to, natural disasters, software virus
infections, etc.
b. Expenses incurred for transport, hotel, daily
allowance, etc., for on-site repairs by Anritsu
engineers necessitated by the above faults
shall be borne by you.
c. The warranty period for faults listed in
article 3a above covered by this EULA shall
be either 6 months from the date of purchase
of this Software or 30 days after the date of
repair, whichever is longer.
vi
4. Export Restrictions
You may not use or otherwise export or
re-export directly or indirectly this Software
except as authorized by Japanese and
United States law. In particular, this
software may not be exported or re-exported
(a) into any Japanese or US embargoed
countries or (b) to anyone on the Japanese or
US Treasury Department's list of Specially
Designated Nationals or the US Department
of Commerce Denied Persons List or Entity
List. By using this Software, you warrant
that you are not located in any such country
or on any such list. You also agree that you
will not use this Software for any purposes
prohibited by Japanese and US law,
including, without limitation, the
development, design and manufacture or
production of missiles or nuclear, chemical
or biological weapons of mass destruction.
5. Termination
Anritsu shall deem this EULA terminated if
you violate any conditions described herein.
This EULA shall also be terminated if the
conditions herein cannot be continued for
any good reason, such as violation of
copyrights, patents, or other laws and
ordinances.
6. Reparations
If Anritsu suffers any loss, financial or
otherwise, due to your violation of the terms
of this EULA, Anritsu shall have the right to
seek proportional damages from you.
7. Responsibility after Termination
Upon termination of this EULA in
accordance with item 5, you shall cease all
use of this Software immediately and shall
as directed by Anritsu either destroy or
return this Software and any backup copies,
full or partial, to Anritsu.
8. Dispute Resolution
If matters of dispute or items not covered by
this EULA arise, they shall be resolved by
negotiations in good faith between you and
Anritsu.
9. Court of Jurisdiction
This EULA shall be interpreted in
accordance with Japanese law and any
disputes that cannot be resolved by
negotiation described in Article 8 shall be
settled by the Japanese courts.
I
About This Manual
Associated Documents
The operation manual configuration of the MS2690A/MS2691A/MS2692A
and MS2830A Signal Analyzer is shown below.
MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Main Frame Operation)
MS2690A/MS2691A/MS2692A and MS2830A Signal Analyzer Operation Manual
(Noise Figure Measurement Function Operation)
MS2690A/MS2691A/MS2692Aand MS2830A Signal Analyzer Operation Manual
(Noise Figure Measurement Function Remote Control)
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer Operation Manual (Main Frame Remote Control)
MS2830A Signal Analyzer
Operation Manual
(Main Frame Operation)Or
MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Signal Analyzer Function
Operation)
MS2690A/MS2691A/MS2692A and MS2830A Signal Analyzer Operation Manual
(Signal Analyzer Function Remote Control)
MS2830A
Signal Analyzer Operation Manual
(Signal Analyzer Function
Operation)
Or
MS2690A/MS2691A/MS2692A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function
Operation)
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control)
MS2830A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function
Operation)
Or
II
• Signal Analyzer Operation Manual (Mainframe)
• Signal Analyzer Operation Manual (Mainframe Remote Control)
Description of basic operations, maintenance procedures, common
functions and common remote functions of the mainframe
• Signal Analyzer Operation Manual (Signal Analyzer Function)
• Signal Analyzer Operation Manual (Signal Analyzer Function Remote Control)
Description of basic operations, common functions and common remote
functions of the signal analyzer
• Signal Analyzer Operation Manual (Spectrum Analyzer Function)
• Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote
Control)
Description of basic operations, common functions and common remote
functions of the spectrum analyzer
• Signal Analyzer Operation Manual (Noise Figure Measurement Function)
<This document>
• Signal Analyzer Operation Manual (Noise Figure Measurement Function
Remote Control)
Description of basic operations, common functions and common remote
functions of the Phase Noise Measurement function
Convention Used in This Manual
Throughout this document, the use of MS269x Series is assumed unless
otherwise specified.
If using MS2830A, change MS269xA to read MS2830A.
In this document, indicates a panel key.
1
III
2
3
4
Appendix Index
5
Table of Contents
About This Manual........................................ I
Chapter 1 Overview.................................... 1-1
1.1 Product Overview.......................................................... 1-2
1.2 Product Composition..................................................... 1-3
1.3 Specifications................................................................ 1-5
Chapter 2 Before Use................................. 2-1
2.1 Part Names................................................................... 2-2
2.2 Signal Path Setup......................................................... 2-12
2.3 Application Startup and Selection................................. 2-13
2.4 Initialization and Calibration.......................................... 2-14
Chapter 3 Measurement ............................ 3-1
3.1 Basic Operation ............................................................ 3-2
3.2 Setting Frequency......................................................... 3-5
3.3 Setting Level ................................................................. 3-10
3.4 Setting Common Items ................................................. 3-12
3.5 Setting the Measure Function....................................... 3-24
3.6 Setting the Marker Function.......................................... 3-28
3.7 Setting the Peak Search Function ................................ 3-29
3.8 Measurement Results................................................... 3-31
Chapter 4 Other Functions ...................... 4-1
4.1 Selecting Other Functions............................................. 4-2
4.2 Setting Title................................................................... 4-2
4.3 Deleting Warm-up Message ......................................... 4-2
Chapter 5 Performance Test .................... 5-1
5.1 Overview of Performance Test..................................... 5-2
5.2 Power Port Operation Check........................................ 5-4
IV.
Appendix A Error Message.......................... A-1
Appendix B Default Value List..................... B-1
Index .......................................................... Index-1
Otros manuales para MS2690A
13
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Instrumento de medición de Anritsu
Anritsu
Anritsu CMA 5000 - UTA Manual de usuario
Anritsu
Anritsu Field Master MS2080A Manual de usuario
Anritsu
Anritsu Spectrum Master MS2712E Manual de usuario
Anritsu
Anritsu MS9740A Manual de usuario
Anritsu
Anritsu MP1800A Manual de usuario
Anritsu
Anritsu Field Master Pro MS2090A Manual de usuario
Anritsu
Anritsu MS2690A Manual de usuario
Anritsu
Anritsu VectorStar ME7848A Series Manual de usuario
Anritsu
Anritsu BTS Master MT8222A Manual de usuario
Anritsu
Anritsu Site Master S810D Manual de usuario
Anritsu
Anritsu VNA master Manual de usuario
Anritsu
Anritsu MS2690A Manual de usuario
Anritsu
Anritsu VNA Master MS2024B Manual de usuario
Anritsu
Anritsu SM/PL Series Manual de uso y cuidado
Anritsu
Anritsu MS27100A Manual de usuario
Anritsu
Anritsu MT8212E Manual de usuario
Anritsu
Anritsu Site Master Manual de usuario
Anritsu
Anritsu VectorStar ME7838 Series Manual de usuario
Anritsu
Anritsu MU104014B Manual de usuario
Anritsu
Anritsu MS2690A Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario