Anritsu MS2690A Manual de usuario
MS2690A/MS2691A/MS2692A
and MS2830A
Signal Analyzer
Operation Manual
Phase Noise Measurement Function
R
e
m
ote
Co
n
t
r
o
l
Third Edition
•For safety and warning information, please read this
manual before attempting to use the equipment.
•Additional safety and warning information is provided
within the “MS2690A/MS2691A/MS2692A and
MS2830A Signal Analyzer Operation Manual
(Mainframe Operation)”. Please also refer to this
document before using the equipment.
•Keep this manual with the equipment.
ANRITSU CORPORATION
Document No.: M-W3118AE-3.0
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the
following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of
the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu
equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this
manual.
Symbols used in manual
DANGER
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
WARNING This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
CAUTION This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and
take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
ii
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer
Operation Manual Phase Noise Measurement Function Remote Control
25 April 2008 (First Edition)
24 June 2011 (Third Edition)
Copyright © 2008-2011, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re-export from you
r
country.
Before re-exporting the product or manuals, please contact us to confirm
whether they are export-controlled items or not.
When you dispose of export-controlled items, the products/manuals need
to be broken/shredded so as not to be unlawfully used for military purpose.
iii
iv
About This Manual
Associated Documents
The operation manual configuration of the MS2690A/MS2691A/MS2692A
and MS2830A Signal Analyzer is shown below.
MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Main Frame Operation)
MS2690A/MS2691A/MS2692A and MS2830A Signal Analyzer Operation Manual
(Phase Noise Measurement Function Operation)
MS2690A/MS2691A/MS2692A and MS2830A Signal Analyzer Operation Manual
(Phase Noise Measurement Function Remote Control)
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer Operation Manual (Main Frame Remote Control)
MS2830A Signal Analyzer
Operation Manual
(Main Frame Operation)
Or
MS2690A/MS2691A/MS2692A
Signal Analyzer Operation Manual
(Signal Analyzer Function
Operation)
MS2690A/MS2691A/MS2692A and MS2830A Signal Analyzer Operation Manual
(Signal Analyzer Function Remote Control)
MS2830A
Signal Analyzer Operation Manual
(Signal Analyzer Function
Operation)
Or
MS2690A/MS2691A/MS2692A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function
Operation)
MS2690A/MS2691A/MS2692A and MS2830A
Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote Control)
MS2830A
Spectrum Analyzer Operation Manual
(Spectrum Analyzer Function
Operation)
Or
I
II
•Signal Analyzer Operation Manual (Mainframe Operation)
•Signal Analyzer Operation Manual (Mainframe Remote Control)
Description of basic operations, maintenance procedures, common
functions and common remote functions of the mainframe
•Signal Analyzer Operation Manual (Signal Analyzer Function)
•Signal Analyzer Operation Manual (Signal Analyzer Function Remote
Control)
Description of basic operations, functions and remote functions of the
signal analyzer
•Signal Analyzer Operation Manual (Spectrum Analyzer Function)
•Signal Analyzer Operation Manual (Spectrum Analyzer Function Remote
Control)
Description of basic operations, functions and remote functions of the
spectrum analyzer
•Signal Analyzer Operation Manual (Phase Noise Measurement Function)
•Signal Analyzer Operation Manual (Phase Noise Measurement Function
Remote Control) <This document>
Description of basic operations, functions and remote functions of the Phase
Noise
III
3
2
1
Table of Contents
About This Manual ........................................ I
Chapter 1 Overview.................................... 1-1
1.1 Overview ....................................................................... 1-2
1.2 Native Mode.................................................................. 1-4
1.3 Setting Numeric Program Data..................................... 1-7
Chapter 2 SCPI Device Message Details.. 2-1
2.1 Selecting Application..................................................... 2-4
2.2 Setting Basic Parameter ............................................... 2-11
2.3 Utility Function .............................................................. 2-26
2.4 Common Measurement Function ................................. 2-30
2.5 Log Plot Measurement.................................................. 2-35
Chapter 3 SCPI Status Register................ 3-1
3.1 Querying Measurement Status ..................................... 3-2
3.2 STATus:QUEStionable Register................................... 3-3
3.3 STATus:OPERation Register ....................................... 3-13
IV.
Chapter 1 Overview
1-1
1
Overview
This chapter provides an overview of the remote control of the Phase
Noise Measurement Function (hereinafter, referred to as “this
application”).
1.1 Overview ....................................................................... 1-2
1.1.1 Interface............................................................ 1-2
1.1.2 Controlled Application....................................... 1-3
1.2 Native Mode.................................................................. 1-4
1.3 Setting Numeric Program Data..................................... 1-7
Chapter 1 Overview
1-2
1.1 Overview
This application can be controlled from an external controller (PC) by
remote control commands using the MS2690/MS2691/MS2692A or
MS2830A Signal Analyzer (hereinafter, referred to as “this instrument”).
The remote control commands are defined by the SCPI format.
1.1.1 Interface
This instrument has GPIB, Ethernet, and USB interfaces for remote
control. Those interfaces cannot be used at the same time.
The interface is automatically determined when a command is received
at the start of communication. This instrument enters the remote state
after the interface has been determined. The front panel lamp
lights during remote interface operation, and goes off during
local-interface operation.
Refer to the “MS2690A/MS2691A/MS2692A and MS2830A Signal
Analyzer Operation Manual (Mainframe Remote Control)” for more
details of the basic operations for remote control, such as interface
setting.
Otros manuales para MS2690A
13
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Instrumento de medición de Anritsu
Anritsu
Anritsu Spectrum Master MS2720T Manual de usuario
Anritsu
Anritsu MP1900A Series Manual de usuario
Anritsu
Anritsu Network Master Series Manual de usuario
Anritsu
Anritsu MS2681A Manual de usuario
Anritsu
Anritsu Spectrum Master MS2711D Manual de usuario
Anritsu
Anritsu MS2690A Manual de usuario
Anritsu
Anritsu Field Master Pro MS2090A Manual de usuario
Anritsu
Anritsu ML2437A Manual del propietario
Anritsu
Anritsu Site Master S120A Manual de usuario
Anritsu
Anritsu VNA Master MS2024B Manual de usuario
Anritsu
Anritsu VectorStar ME7848A Series Manual de usuario
Anritsu
Anritsu Field Master MS2080A Manual de usuario
Anritsu
Anritsu VectorStar ME7848A-0272 Manual de usuario
Anritsu
Anritsu MP1595A Manual de usuario
Anritsu
Anritsu Site Master S820D Manual de usuario
Anritsu
Anritsu PIM Master MW82119A Manual de usuario
Anritsu
Anritsu MT8801C Manual de usuario
Anritsu
Anritsu ms9710b Manual de usuario
Anritsu
Anritsu MS2665C Manual de usuario
Anritsu
Anritsu MP1777A Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario