Anritsu MD1230B Manual de usuario
Quick Start Guide
MU120131A/32A
PON Quick Start Guide
MD1230B
Data Quality Analyzer
MU120131A/32A PON Quck Start Guide
1
Contents
1. Introduction................................................................................................................................ 2
1.1. Structure of Guide............................................................................................................ 2
2. Starting ...................................................................................................................................... 3
2.1. Installing MD1230B............................................................................................................ 3
2.2. Installing Modules.............................................................................................................. 3
2.3. Power-on/off....................................................................................................................... 3
2.4. Starting............................................................................................................................... 4
3. Shared Settings......................................................................................................................... 5
3.1. Obtaining Ownership ......................................................................................................... 5
3.2. Setting Ports....................................................................................................................... 5
4. End-to-End Measurement......................................................................................................... 7
4.1. Connecting DUT ................................................................................................................ 7
4.2. Creating OLT-side Tx Frames (and Setting OLT->ONU Stream (Down Signal)) .............. 8
4.3. Creating ONU-side Tx Frames (and Setting ONU->OLT Stream (Up Signal))............... 12
4.4. Checking Flow from Each ONU (Setting OLTONU Tx/Rx Counter)............................ 17
4.5. Checking OLT→ONU (Down SIgnal) Flow~Setting Custom Counter............................. 26
4.6. Testing Load..................................................................................................................... 29
5. Monitoring E-PON Systems.................................................................................................... 32
5.1. Connecting DUT .............................................................................................................. 32
5.2. Checking MPCP Control and OAM Function................................................................... 33
5.3. Application Example 1: Verifying DBA Function.............................................................. 39
5.4. Application Example 2: Verifying QoS............................................................................. 42
6. Summary................................................................................................................................. 46
MU120131A/32A PON Quck Start Guide
2
1. Introduction
The MD1230/MP1590 family (hereafter MD1230B) is a measuring instruments designed for
next-generation networks. This documents explains its applications for PON used in increasingly
common FTTH networks (B-PON, E-PON (GE-PON), G-PON).
First, it explains the methods for performing simultaneous one-way and two-way End-to-End
measurement of all the ONU and OLT equipment in a 32-branch PON system with a single
measuring instrument.
Additionally, it explains the method for verifying E-PON frames by capturing and decoding system
frames, especially E-PON related.
1.1. Structure of Guide
Fig. 1 Structure of Guide
*This document presumes use of the MU120131A/32A module (Ver. 7.0 and later). For the
procedure for installing or upgrading Ver. 7.0 of the MD1230 software, see the version upgrade
procedure.
*Upgrade the firmware according to the version upgrade procedure, check the installation and
then connect to the unit.
Note: When the Ver. 7.0 installer is executed. All setting conditions are cleared. When
wanting to save the settings of the older version, use the Save settings function
before upgrading.
Introduction
Shared Settings
End to End Measurement
(B-PON, E-PON, G-PON etc.)
E-PON System Monitoring
(E-PON)
Summary
MU120131A/32A PON Quck Start Guide
3
2. Starting
This section explains installation of the MD1230B and the power-on and start-up procedures.
2.1. Installing MD1230B
Install the MD1230B on a flat and stable surface.
The MD1230B has a cooling fan in the back panel. Position the MD1230B so that it is
at least 10 cm from walls and obstructions to allow sufficient cooling air flows.
Supply power in the voltage ranges of 100~120 Vac or 200~240 Vac at a frequency of
50~60 Hz. The power consumption is 600 Vac.
> 10 cm
2.2. Installing Modules
Install three MU120131Aunits in Slots 2 to 4 and one MU120132A in Slot 5.
2.3. Power-on/off
(1) At power-on
Plug the power cord into the power socket.
Set the power switch to ON.
(2) At power-off
Shutdown the MD1230B in the same way as a normal PC and set the power switch to
OFF.
Power switch
MU120131A/32A PON Quck Start Guide
4
2.4. Starting
Main start-up
At power-on, the Selector screen shown above is displayed. Click “Main application”.
The screen changes to the Measurement screen automatically after about 15
seconds.
MU120131A/32A PON Quck Start Guide
5
3. Shared Settings
This section explains the procedures for reserving and setting ports.
3.1. Obtaining Ownership
Before starting measurement, the ports to be measured must be reserved.
Right-click Unit1 and select “Reservation...” . The ports of usable modules that can be
used are listed as shown below; place checkmarks in the required ports and press the
“Check all” button.
3.2. Setting Ports
After reserving the ports to be measured, set the ports.
MU120131A/32A PON Quck Start Guide
6
Right-click Port1(Unit1:2:1) and select “Port Setting...”.
Open the “IPv4” selector screen and set “IPv4 Address:”, “Netmask:”, and ‘Gateway:”.
(Any values can be set but here “192.168.0.1”, “255.255.255.0”, and “192.168.0.255:”
are used as examples.)
Put checkmarks in “Reply to this port ARP request”, and in “Reply to this port PING
request” (when performing ARP and PING).
Set “MAC Address:”. (Any value can be set but here “00-00-00-00-00-01” is used as
an example.)
Set “Test Pattern:”to “Cross PRBS 31”
Set Port1~Port12 for Unit2, Unit3, and Unit4 in the same way. Set “IPv4 Address:”
sequentially in the range of “192.168.0.1 to 36”, and ”MAC Address:”in the sequential range
of ”00-00-00-00-00-01~24” (hexadecimal).
MU120131A/32A PON Quck Start Guide
7
4. End-to-End Measurement
This section explains the end-to-end measurement procedure by connecting the measuring
instrument to the OLT and the outside of each ONU.
In concrete terms, this measurement checks that data is flowing normally to each ONU by
measuring Throughput and Latency by counting Bit Rate and number of Frames. In addition
sequence errors are detected by imposing a load by varying the number of Frame and gaps and
using the packet BER measurement function to confirm that packet loss does not occur.
4.1. Connecting DUT
Connect ONI1~32 to Unit1 Port1~Port12 of the MU120131A, Unit2 Port1~Port12, and Unit3
Port1~Port8. Connect the OLT to Unit3 Port12.
1
PON System
2
31
32
36
ONU
OLT
MAC:00-00-00-00-00-01
IPv4:192.168.0.1
MAC:00-00-00-00-00-20
IPv4:192.168.0.32
MAC:00-00-00-00-00-24
IPv4:192.168.0.36
MU120131A/32A PON Quck Start Guide
8
4.2. Creating OLT-side Tx Frames (and Setting OLT->ONU Stream (Down Signal))
(Objective) Using 32-branch PON, create test signal emulating real network with different
payloads in each Frame
(Procedure) Increment the MAC address for each ONU address and create a multiple-address
stream.
Input a PRBS pattern amd perform BER measurement.
(Results, Goal) Create OLT-side Tx Frames~Create OLT→ONU Stream (Down signal)
Creating OLT-side Tx Frames (Tx Stream)
Select Port12 of Unit4.
Press “Add” at the □Tx Stream screen and create the stream.
Press “Edit...” to edit the created stream.
MU120131A/32A PON Quck Start Guide
9
Select “Jump to Stream” at “Distribution:”of Stream Control and “Frame per Burst:”to
32. (This returns to the default stream after sending 32 streams.)
Setting “Inter Frame Gap:”changes the Tx rate. Here, select “Fixed” at ”Inter Frame
Gap:”and set “Unit” of ”Value:”to “%” and “6.5625%”. (The setting is 6.5625% (5
Mbps) here, because the data is the same as video traffic of several Mbps flowing on
an actual network.)
Set “Frame Length” at [General] of Frame Setting. (When “Auto” is selected, 64 byte
is set automatically. With E-PON Frames, 64 bytes is common, but set 70 bytes
because we want a PRBS test frame of more than 28 bytes in the Data Field.)
Leave “Protocol:”unchanged as “IPv4”. (This is the common protocol setting.)
Put a checkmark in VLAN (because group division is commonly by LAN for each
Tabla de contenidos
Otros manuales de Instrumento de medición de Anritsu
Anritsu
Anritsu Site Master S311D Manual de usuario
Anritsu
Anritsu MS2830A Manual de usuario
Anritsu
Anritsu 37 C Series Manual de usuario
Anritsu
Anritsu VectorStar ME7838 4 Series Manual de usuario
Anritsu
Anritsu ShockLine MS46131A-010 Manual de usuario
Anritsu
Anritsu Field Master MS2080A Manual de usuario
Anritsu
Anritsu 37 D Series Manual de usuario
Anritsu
Anritsu Microwave Site Master S820E Manual de usuario
Anritsu
Anritsu Field Master Pro MS2090A Manual de usuario
Anritsu
Anritsu MW9076 Series Manual de usuario
Anritsu
Anritsu VNA Master MS2026C Manual de usuario
Anritsu
Anritsu PIM Master MW8219A Manual de usuario
Anritsu
Anritsu VectorStar ME7848A-0272 Manual de usuario
Anritsu
Anritsu Field Master Pro Manual de usuario
Anritsu
Anritsu PIM Master MW8208A Manual de usuario
Anritsu
Anritsu MS2665C Manual de usuario
Anritsu
Anritsu MT8852B Manual de usuario
Anritsu
Anritsu MS2665C Manual de usuario
Anritsu
Anritsu LMR Master S412E Manual de usuario
Anritsu
Anritsu Field Master Pro MS2090A Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario