Amprobe AMCM100 Manual de usuario

CM100

Carbon Monoxide

Meter

Users Manual

• Mode d’emploi

• Bedienungshandbuch

• Manual d’Uso

• Manual de uso

• Användarhandbok

English

CM100

Carbon Monoxide Meter

Users Manual

CM100_Rev001

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for 1 year from the

date of purchase. This warranty does not cover fuses, disposable batteries or damage from accident,

neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling.

Resellers are not authorized to extend any other warranty on Amprobe’s behalf. To obtain service

during the warranty period, return the product with proof of purchase to an authorized Amprobe

Test Tools Service Center or to an Amprobe dealer or distributor. See Repair Section for details.

THIS WARRANTY IS YOUR ONLY REMEDY. ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED

OR STAUTORY - INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR

MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY

CAUSE OR THEORY. Since some states or countries do not allow the exclusion or limitation of an

implied warranty or of incidental or consequential damages, this limitation of liability may not apply

to you.

Repair

All test tools returned for warranty or non-warranty repair or for calibration should be accompanied

by the following: your name, company’s name, address, telephone number, and proof of purchase.

Additionally, please include a brief description of the problem or the service requested and include

the test leads with the meter. Non-warranty repair or replacement charges should be remitted in the

form of a check, a money order, credit card with expiration date, or a purchase order made payable

to Amprobe® Test Tools.

*(Correspondence only – no repair or replacement available from this address. European customers

please contact your distributor.)

➊Display current CO value.

➋Display maximum CO value.

➌Low battery indicator.

ppm

Max

CO Meter

LCD display

➊Turn the meter on and off. Select the alarm value.

➋Turn on and off the backlight. Reset the maximum

CO value. Select the calibration value.

➌Enter calibration mode by pressing both pushbuttons

Function Keys

CM100

Carbon Monoxide Meter

CONTENTS

Unpacking and Inspection..................................................................................................................5

Introduction.........................................................................................................................................5

Features..........................................................................................................................................5

CO Levels and Standards.....................................................................................................................5

Operation ............................................................................................................................................6

1. Power on/off ..............................................................................................................................6

2. Alarm setting .............................................................................................................................6

3. Measurement.............................................................................................................................6

4. Backlight.....................................................................................................................................6

5. Low battery indicator................................................................................................................7

6. Auto power off..........................................................................................................................7

Calibration...........................................................................................................................................7

0ppm calibration............................................................................................................................7

100ppm/500ppm calibration ........................................................................................................7

Troubleshooting..................................................................................................................................7

Precautions ..........................................................................................................................................8

Technical Speciﬁcations ......................................................................................................................8

UNPACKING AND INSPECTION

Your shipping container should include:

1 CM100 Carbon Monixide Detector

3 AAA battery

1 Carrying Case

1 Users Manual

INTRODUCTION

Congratulations on your purchase of this digital pen type CO meter. Please read the manual

completely before using the meter.

Features

Adjustable CO warning level•

Dual and digital display•

Backlight for operation in dark area•

Low battery indicator•

Auto power off function•

CO LEVELS AND STANDARDS

ppm Symptoms and applicable standard

0-1 Normal background levels

Maximum indoor air quality level:

Maximum allowable concentration per ASHRAE Residential standards 62-1989 for

living area.

25 Maximum limit 8 hrs of continuous exposure per California OSHA Workplace

standards.

35 Maximum 8 hrs average exposure level per US OSHA workplace standards.

50 Maximum concentration for continuous exposure in any 8 hrs average level per

OSHA standards.

100 Remove employees from enclosed space if the CO concentration exceeds 100ppm

per OSHA exposure limit.

200 Mild headache, fatigue, nausea and dizziness w/i 2-3 hrs.

ppm Symptoms and applicable standard

400 Frontal headache, life threatening after 3hrs. Maximum concentration in ﬂue gas

per EPA and AGA.

800 Dizziness, nausea, convulsions, death w/i 2-3 hrs.

1600 Nausea w/I 20 min; death w/I 2-3 hrs

OPERATION

1. Power on/off

Press• �to turn on and off the meter. When meter is power on, the preset alarm value and

current air temperature will be blinking on the LCD.

Meter will perform Self-Test for 15 seconds. A beep after the self test indicates that the•

meter is ready to use.

A 25 ppm

26 C

IMPORTANT:

It is recommended to turn on the meter in an area free of CO since high CO level may cause

failure in passing Self-Test.

2. Alarm setting

The meter alarm is preset to 25ppm to warn about possible danger.•

User can adjust the alarm level by choosing one. The available CO gas levels: 25, 30, 35, 45,•

50, 70, 100 and 200ppm.

Release the pushbutton to select the preferred value. The meter will return to Self-Test•

mode in a few seconds.

3. Measurement

The meter detects the existence of CO in the environment and displays the reading in ppm.•

It also indicates the maximum value (at lower side of the LCD) of all readings.

Reset the maximum value by pressing• pushbutton for two seconds in measuring mode.

4. Backlight

Press pushbutton to turn on and off the backlight.

5. Low battery indicator

Appears on the LCD when battery voltage is low.

6. Auto power off

The meter turns itself off automatically after 15 minutes of non-operation.

CALIBRATION

To enter the calibration mode, turn off meter and press �+ pushbuttons simultaneously

for 2 seconds. It will show a blinking ppm on the upper display and calibration value ”0” at

lower side. Now the meter is running 0ppm calibration as default.

0ppm calibration

The preset calibration value is 0ppm. Put the meter in an area free of CO and enter the

calibration mode. It calibrates automatically. The LCD is now displaying a blinking ppm value

at the upper side which slowly runs down to 0 or minus value, then stops blinking when the

calibration is completed. This takes about 10 minutes.

Note:

Don’t be alarmed if high ppm or minus value shows up when entering calibration mode. It will

go down and approach to 0 in seconds. The erratic readings are caused by electromagnetic

interference (EMI) in the environment, such as computers or cell phone. It is required to have

the meter away from these types of interference, otherwise the calibration may take much

longer time or never complete.

100ppm/500ppm calibration

For other standard calibration, press1. pushbutton and hold to select the calibration

value. (0, 100, 500ppm).

Place the meter into the sealed box ﬁlled with standard gas (e.g. 100ppm/500ppm) for 152.

minutes. Then the Calibration will be done automatically.

Check if the reading meets calibration value. If it does, the calibration is well completed. If3.

not, repeat the procedure.

TROUBLESHOOTING

Device cannot power ON

Check if the time since power on is over 300 mS.1.

Make sure the batteries are in good contact and correct polarity.2.

Replace the batteries and try again3.

Display disappears

Check whether the low battery indicator shows before display disappears. If so, replace the

batteries.

Calibration failure

Check if the low battery indicator shows before calibration. If so, replace a new battery and1.

try again.

Make sure the standard gas is correct.2.

E 2.: The value is underﬂow.

E 3.: The value is overﬂow.

E 4.:The value is “error”because of some original data.

E 31.: A/D failure, return the meter to the dealer for repair.

E 33.: Some measurement circuits failure, return the meter to the dealer for replacement or

repair.

E 35.: Self-Test failure. Turn on the meter again in other area free of CO.

Sensor failure. Return the meter to the dealer for repair.

PRECAUTIONS

Keep the meter away from electromagnetic interference (EMI) which may cause erratic1.

readings.

Recovering time is required when meter exposed to high level CO. The longer the exposure,2.

the longer recovering time is needed.

Self-Test after power on is to test the sensor and circuit condition.3.

TECHNICAL SPECIFICATIONS

CO range: 0~999ppm

Resolution: 1 ppm

Accuracy: ± 20% at 0~100ppm; ±15% at 100~500ppm (at 20°C±5% and 50%±20%RH)

Battery: 3 AAA alkaline. Battery life is 250 hours when backlight is off and 35 hours when

backlight is on.

Français

CM100

Compteur de monoxyde

de carbone

Mode d’emploi

CM100_Rev001

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de Amprobe

Amprobe

Amprobe SOLAR-100 Manual de usuario

Amprobe

Amprobe UAT-600 Series Manual de usuario

Amprobe

Amprobe TMD-10 Manual de usuario

Amprobe

Amprobe AD40B Manual de usuario

Amprobe

Amprobe VP-600SB Manual de usuario

Amprobe

Amprobe THWD-2 Manual de usuario

Amprobe

Amprobe TMA40 Manual de usuario

Amprobe

Amprobe AT-2005-A Manual de usuario

Amprobe

Amprobe MEGATEST 5000 Manual de usuario

Amprobe

Amprobe PM55A Manual de usuario

Amprobe

Amprobe DM-5 Manual de usuario

Amprobe

Amprobe ACD-45PQ Manual de usuario

Amprobe

Amprobe SOLAR-500 Manual de usuario

Amprobe

Amprobe MAN15 Manual de usuario

Amprobe

Amprobe AC50A Manual de usuario

Amprobe

Amprobe WT-30 Manual de usuario

Amprobe

Amprobe TMA10A Manual de usuario

Amprobe

Amprobe TDR-400 Manual de usuario

Amprobe

Amprobe SM70 Manual de usuario

Amprobe

Amprobe ACD-23SW Manual de usuario

Amprobe

Amprobe TIC 300 PRO Manual de usuario

Amprobe

Amprobe ALC-110 Manual de usuario

Amprobe

Amprobe TACH20 Manual de usuario

Amprobe

Amprobe THWD-3 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario