AMK DT62 Manual de usuario

Tabla de contenidos

Manuales populares de Oradores de otras marcas

argon audio

argon audio IE20 Manual de usuario

Denon

Denon SC-N7 Manual de usuario

Gemline

Gemline Ace 3952 Manual de usuario

Focal

Focal ON WALL 300 Manual de instrucciones

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manual de usuario

SoundLogic

SoundLogic BCCS-6/6395 Manual de usuario

Peavey

Peavey DTH 218 Manual de usuario

Avantree

Avantree Pluto Air Manual de usuario

Morel

Morel Integra Series INTEGRA OVATION 4 Manual de usuario

Oppo

Oppo SONICA Manual de usuario

Bose

Bose SoundLink Wireless Music System Manual de usuario

Rocksteady

Rocksteady Stadium Manual de usuario

Bowers & Wilkins

Bowers & Wilkins 4 Manual de usuario

Sonance

Sonance SONOS OUTDOOR Series Manual de usuario

Electro-Voice

Electro-Voice EVID FM4.2 Manual de usuario

Pioneer

Pioneer XW-HTD630 Manual de usuario

Onn

Onn BWA16AA002 Manual de usuario

HP

HP GL313AA - USB Speakers PC Multimedia Manual de usuario

This set up guide contains installation instruction of the AMK DT62, AMK’s Dante

System enabled network self amplified speaker. This speaker is designed to use in

plenum rated ceiling spaces and can be dropped into standard square (2’ x 2’ or

600mm by 600mm) or rectangular (2’ x 4” or 600mm by 1200mm) false ceiling tile

space with a tile bridge.

Important Safety Instructions.

WARNING: May result in serious injury. Installation and service must be performed by

authorized personnel only

1. Read these instructions

2. Keep these instructions

3. Heed all warnings

4. Follow all instructions.

5. Do not use this speakers near water

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with manufacturer’s

instructions.

8. Do not install these speakers near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Use only attachments/accessories specified by manufacturer

10. If the speakers have not been used for some time, unplug the speakers.

Or when there is a lightning storms, please unplug the speakers for safety.

Parts Check List.

2x2 lay in PoE+ self amplified network speaker (1)

2x2 lay in companion speaker (1)

Handy Box Covers (3)

12407 Mukilteo Speedway, Ste. 130

Lynnwood, WA 98087

p. 800.438-4026 f. 877.721.8107

tech@amkspeakers.com

www.amkspeakers.com

Installation Manual

DT62

Dante System Network Enabled Speaker

For Suspended Ceiling Installations

Remove the ceiling tile from the selected speaker location that is to be cut from the

ceiling, and an adjacent ceiling tile for access.

Installation

1. Make sure that all the power is removed.

2. Remove and cut ceiling tile as sown below. If the tile is 2’ x 4’, then you will

need to cut the tile into half. Install the T-rail crosspiece into the ceiling

opening up against the cut tile, as shown below.

Carefully measure and

draw the line at the

halfway point.

Ceiling Tile

T-rail

Crosspiece

needs to be

installed.

3. Install the T-rail in a rectangular

tile –When the ceiling uses

rectangular tiles, install the T-rail

crosspiece into the ceiling opening

up against he cut tile.

4. Connect appropriate cables and

plugs. Connect the right plugs for

the audio and power into the jacks

on the top of the enclosure.

Different types of connections are

shown on next page.

Lay in the speaker appropriately as it is

shown above.

Three Light Indicators:

When RJ45 connection is made, you should be seeing some lights

blinking on the right side of the RJ45 connection handy box as

shown.

From top to bottom, it will be Power, Dante, and Status.

○Power: This shows the power coming from PoE+ network switch. If there is no

power present, then the light will not turn green. The speaker must be

running from PoE+ network switchin order to get the green light.

○ Dante: This will blink red in the beginning as it is trying to connect with the computer

system. When connection is made and Dante signal is confirmed, the light

will turn green.

○ Status: As the audio signal gets transmitted into the speaker system, the light will

blink green as the signals go through.

Companion Speaker connection.

Connect the audio wire from active speaker to the passive speakers. The passive

speaker will be broadcasting different program material. Make sure that the passive

speaker is installed at the different zone of the building as specified by your designer.

Connect the audio wire from active speaker to the passive speakers.

Punch the one of the knockout on the side of the handy box. After the connection is

made, make sure the close the handy box with the cover provided.

A single 2

position

phoenix

connection

inside of the

handybox.

Main Active Speaker Wire Connection:

Connect the audio wires connecting active speakers to three passive speakers through

conduit. Pre terminate the wire and connect the Phoenix plug to the wire. Punch the

knockout on the side of the handy box. After the connection is made, make sure to

close the handy box with the cover provided. The audio wires should be a two

conductor wire with recommended 18 AWG wire.

Connect the Ethernet signal wires through conduit, terminate with RJ45 connector,

punch the one of the knock out where RJ45 jack is located, than plug it into the

speaker. After the connection is made, make sure to close the handy box with the

cover provided.

Warranty

The speakers should be not open, altered, tampered without the consulting with AMK,

otherwise you will lose the warranty on the speaker. If the speaker is a need for

additional support for seismic mounting, please consult with AMK.

Connection to passive

speaker for different

channel at separate

zone.

The connection

should be made Cat5

or above cable for the

Ethernet connection.

A single 2 position

phoenix connection

inside of the

handybox.