AMK SQ602 Manual de usuario
This set up guide contains installation instruction of the AMK SQ602 series of AMK’s
2x2 lay in ceiling speaker. This speaker is designed to use in plenum rated ceiling
spaces and can be dropped into standard square (2’ x 2’ or 600mm by 600mm) or
rectangular (2’ x 4” or 600mm by 1200mm) false ceiling tile space with a tile bridge.
Important Safety Instructions.
WARNING: May result in serious injury. Installation and service must be performed by
authorized personnel only
1. Read these instructions
2. Keep these instructions
3. Heed all warnings
4. Follow all instructions.
5. Do not use this speakers near water
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with manufacturer’s
instructions.
8. Do not install these speakers near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Use only attachments/accessories specified by manufacturer
Parts Check List.
2x2 lay in ceiling speaker (1)
Handy Box Cover (1)
12407 Mukilteo Speedway, Ste. 130
Lynnwood, WA 98087
p. 800.438-4026 f. 877.721.8107
tech@amkspeakers.com
www.amkspeakers.com
Installation Manual
SQ602
SQ602T70V15W
2x2 lay in ceiling speake
r
For Suspended Ceiling Installations
Remove the ceiling tile from the selected speaker location that is to be cut from the
ceiling, and an adjacent ceiling tile for access.
Installation
1. Make sure that all the power is removed.
2. Remove and cut ceiling tile as sown below. If the tile is 2’ x 4’, then you will
need to cut the tile into half. Install the T-rail crosspiece into the ceiling
opening up against the cut tile, as shown below.
Carefully measure and
draw the line at the
halfway point.
Ceilin
g
Tile
T-rail
Crosspiece
needs to be
installed.
3. Install the T-rail in a rectangular
tile –When the ceiling uses
rectangular tiles, install the T-rail
crosspiece into the ceiling opening
up against he cut tile.
4. Connect appropriate cables and
plugs. Connect the right plugs for
the audio and power into the jacks
on the top of the enclosure.
Different types of connections are
shown on next page.
Lay in the speaker appropriately as it
is shown above.
Main Active Speaker Wire Connection:
Connect the audio wires connecting active
speakers to three passive speakers through
conduit. The audio wires needs to be
stripped for about half inch. Make sure that
the positive and negative, or hot and ground,
wires are correctly connected. Tie the wire
nut, place the connections inside of the handy
box. Close the handy box with the
connections provided.
For 70volt version, SQ602T70V15W, the hot, or plus wires will be in several wattages.
Choose the wattage that is used and connect to the plus (or hot) part of the audio wire.
The wattage of the each transformers are indicated on the speaker with different color
label.
Make sure to trim off the unused wattage wires and use the electrical tape tie them.
Place all the wires inside of the handy box. Close the handy box with the connections
provided.
Warranty
The speakers should be not open, altered, tampered without the consulting with
AMK, otherwise you will lose the warranty on the speaker. If the speaker is a need
for additional support for seismic mounting, please consult with AMK.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Oradores de AMK
AMK
AMK DS8 Series Manual de usuario
AMK
AMK DS84-B Manual de usuario
AMK
AMK DT82-A-X Manual de usuario
AMK
AMK DT84-B Manual de usuario
AMK
AMK DS81 Manual de usuario
AMK
AMK DS81-A Manual de usuario
AMK
AMK PCS Series Manual de usuario
AMK
AMK DS61-A-X Manual de usuario
AMK
AMK DT64-A Manual de usuario
AMK
AMK DT82-B-X Manual de usuario
AMK
AMK Dante DS84 Manual de usuario
AMK
AMK DS64-C Manual de usuario
AMK
AMK DS82-B Manual de usuario
AMK
AMK DT64-B Manual de usuario
AMK
AMK DS6 Series Manual de usuario
AMK
AMK Dante DS62 Manual de usuario
AMK
AMK DS84-C Manual de usuario
AMK
AMK DT62 Manual de usuario
AMK
AMK DS81-A-X Manual de usuario
AMK
AMK DT6 Series Manual de usuario
