AMK DT64-B Manual de usuario
This set up guide contains installation instruction of the AMK DT64-B series
of AMK’s Dante System enabled network self amplified speaker. This
speaker is designed to use in plenum rated ceiling spaces and can be
dropped into standard square (2’ x 2’ or 600mm by 600mm) or rectangular
(2’ x 4” or 600mm by 1200mm) false ceiling tile space with a tile bridge.
Important Safety Instructions.
WARNING: May result in serious injury. Installation and service must be
performed by authorized personnel only
1. Read these instructions
2. Keep these instructions
3. Heed all warnings
4. Follow all instructions.
5. Do not use this speakers near water
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with
manufacturer’s instructions.
8. Do not install these speakers near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Use only attachments/accessories specified by manufacturer
10. If the speakers have not been used for some time, unplug the
speakers. Or when there is a lightning storms, please unplug the
speakers for safety.
Parts Check List.
2x2 lay in PoE+ self amplified network speaker (1)
2x2 lay in companion speakers (3)
Handy Box Covers (5)
12407 Mukilteo Speedway, Ste. 130
Lynnwood, WA 98087
p. 800.438-4026 f. 877.721.8107
tech@amkspeakers.com
www.amkspeakers.com
Installation Manual
DT64-B
Dante System Network Enabled Speaker
For Suspended Ceiling Installations
Remove the ceiling tile from the selected speaker location that is to be cut
from the ceiling, and an adjacent ceiling tile for access.
Installation
1. Make sure that all the power is removed.
2. Remove and cut ceiling tile as sown below. If the tile is 2’ x 4’, then
you will need to cut the tile into half. Install the T-rail crosspiece into
the ceiling opening up against the cut tile, as shown below.
Carefully measure
and draw the line at
the halfway point.
Ceilin
g
Tile
T-rail
Crosspiece
needs to be
installed.
3. Install the T-rail in a
rectangular tile –When the
ceiling uses rectangular tiles,
install the T-rail crosspiece into
the ceiling opening up against
he cut tile.
4. Connect appropriate cables
and plugs. Connect the right
plugs for the audio and power
into the jacks on the top of the
enclosure. Different types of
connections are shown on next
page.
Lay in the speaker appropriately as it
is shown above.
Main Active Speaker Wire Connection:
Connect the audio wires connecting active speakers to three passive
speakers through conduit. Pre terminate the wire and connect the Phoenix
plug to the wire. Punch the knockout on the side of the handy box. After
the connection is made, make sure to close the handy box with the cover
provided. The audio wires should be a two conductor wire with
recommended 18 AWG wire.
Connect the Ethernet signal wires through conduit, terminate with RJ45
connector, punch the one of the knock out where RJ45 jack is located, than
plug it into the speaker. After the connection is made, make sure to close
the handy box with the cover provided.
The connection on the top
as shown is to be
connected to same zone
speaker (Channel 1) as
the main active PoE
speaker. CONNECTOR
MARKED IN PINK
COLOR WILL BE THE
SAME CHANNELAS
ACTIVE SPEAKER
The bottom two connections are
for audio output to two (2)
passive speakers for different
zone (Channel 2)
The connection should be
made Cat5 or above cable
for the Ethernet
connection.
Companion Speaker connection.
Connect the audio wire from active speaker to the passive speakers. Make
sure that the connections are for the right channels of the speaker.
Punch the one of the knockout on the side of the handy box. After the
connection is made, make sure the close the handy box with the cover
provided.
There is a single 2 position phoenix
connection inside of the handy box.
THE PASSIVE SPEAKER THAT WILL
BE THE SAME CHANNEL SPEAKER
AS THE ACTIVE SPEAKER HAS PINK
MARK ON THE PHOENIX
CONNECTOR.
Warranty
The speakers should be not open, altered, tampered without the
consulting withAMK, otherwise you will lose the warranty on the speaker.
If the speaker is a need for additional support for seismic mounting,
please consultant withAMK.
Tabla de contenidos
Otros manuales de Oradores de AMK
AMK
AMK DS82-A-X Manual de usuario
AMK
AMK DT62-A-X Manual de usuario
AMK
AMK DS6 Series Manual de usuario
AMK
AMK DT81-A Manual de usuario
AMK
AMK DT84-B Manual de usuario
AMK
AMK DS62-A Manual de usuario
AMK
AMK DT64-A Manual de usuario
AMK
AMK DS84-C-X Manual de usuario
AMK
AMK Dante DS84 Manual de usuario
AMK
AMK DT62 Manual de usuario
AMK
AMK DS61-A-X Manual de usuario
AMK
AMK DT64-C Manual de usuario
AMK
AMK DS61-A Manual de usuario
AMK
AMK DS84-B Manual de usuario
AMK
AMK DS82-B Manual de usuario
AMK
AMK DS81-A-X Manual de usuario
AMK
AMK DT84-C Manual de usuario
AMK
AMK QT series Manual de usuario
AMK
AMK DS61 Manual de usuario
AMK
AMK DT61-A-X Manual de usuario
