American Standard Savona Elite 2901E SERIES Manual de usuario

INSTALLATION INSTRUCTIONS

752867-100 Rev. D © American Standard Inc. 2003

All product names listed herein are trademarks of

American Standard Inc. unless otherwise noted.

HIGH GLOSS ACRYLIC

SHOWN LESS ALL FITTINGS

SAVONA ELITE™ WHIRLPOOL

2901E SERIES

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

THANK YOU...

for selecting an American Standard bath. Your new

bath is shipped to you after careful inspection. The

whirlpool version is completely assembled with pump,

motor, and system piping. All you need to finish the

installation are your selected fittings and electrical

connections for a whirlpool.

To insure maximum performance and pleasure from

this product, please follow the instructions and

cautions.

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor

immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before

enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect

the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,

motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and

enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead

(required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

List of Optional Components (not included):

• Flex-Jet Pulse Jet Kit*

• Flex-Jet Soft Jet Kit*

• E-Z-Install Heater*

• Tile Bead Kit*

List of Required Components (not included):

• Drain* • Bath Filler*

* see your Home Depot Retailer

List of Required Tools and Supplies:

Tools

• Level

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard

Woodworking Tools

• Personal Safety

Equipment

• Caulking Gun

Supplies

• Nails

• Putty

• Caulking (waterproof)

• 1 x 3 or 2 x 2

Stringers

• Drop Cloth

• 20 amp GFI

Outlet

• Cement, Plaster,

Grout

GENERAL SPECIFICATIONS FOR 2901E WHIRLPOOL

71-1/4 x 43-1/2 x 22 In.(1810 x 1105 x 559mm)

152 Lbs. (68 Kg.)

936 Lbs. (421 Kg.)

94 Gal. (356 L)

86 Gal.(326 L)

44 x 28 In. (1118 x 711mm)

67-1/2 x 33 In. (1715 x 838mm)

16-1/4 In. (413mm)

43 Lbs./Sq.Ft. (211 Kgs./Sq.m)

27.8

61.5

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

WHIRLPOOL MIN. OPERATING VOL.

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

PTS.

CUBE (FT3)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

2.1 HP, 14.4 AMPS, 120V.PUMP

1810mm

(71-1/4)

905mm

(35-5/8)

C/L

19mm

(3/4)

TYP.

1105mm

(43-1/2)

552mm

(21-3/4)

305mm

(12) 140mm

(5-1/2)

508mm

(20)

559mm

(22)

178mm

(7)

OUTLINE OF

1772mm X

1067mm

(69-3/4 X 42)

CUTOUT

ON/OFF

SWITCH

PUMP

PROVIDE ACCESS

TO PUMP FOR SERVICE

ON ALL INSTALLATIONS

229mm X 305mm

(9 X 12) FLOOR

CUTOUT

RECOMMENDED

FITTING LOCATION

64 X 279mm (2-1/2 X 11)

●

C/L OF 1-1/2 O.D.

DRAIN OUTLET

C/L OF OVERFLOW

51mm

(2)

38mm

(1-1/2) 89mm

(3-1/2)

■ LEVELING STRINGER

NOT FOR SUPPORT

ROUGH

FLOOR

1-1/2 O.D. TAILPIECE

INTEGRAL

FEET

89 mm

(3-1/2)

44 mm

(1-3/4)

1-1/2 N.P.T.M.

THREADS

IN-LINE HEATER

REMOVABLE

BLANK

752867-100 Rev.D (2)

INSTALLATION AND FRAMING INSTRUCTIONS

The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs

as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an

access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for

access to the drain components.

1. Position the whirlpool into the installation opening and level the deck, shimming the integral support feet as necessary.

2. Install drain components to the whirlpool following the manufacturers instructions. Before replacing your whirlpool for final

installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for

suggested opening size and location dimensions.

3 . Replace whirlpool and re-shim the integral support feet, shimming the entire length of the support feet. Secure the shims

using construction adhesive, silicone, mortar or equivalent materials. While not a necessity, the use of a foundation base

consisting of cement (e.g. Sakrete), mortar, or grout will help provide a solid and secure installation.

TYPICAL PIER TYPE INSTALLATION

LEVELING SURFACE

WATERPROOF

SEALANT

SUNKEN OR ISLAND

INSTALLATION

BATH

AS DESIRED42"

(1067mm)

CUTOUT

AS DESIRED

69-3/4"

(1772mm)

CUTOUT

(508mm)

ACCESS PANEL

(610mm)

(305mm)

UNLESS AN ACCESS OPENING OF AT LEAST

12" X 24" (305 X 610MM) IS PROVIDED,

WARRANTY SERVICE WILL NOT BE PERFORMED.

ELECTRICAL DIAGRAM

READ AND FOLLOW ALL INSTRUCTIONS

BLACK

WHITE

120 VAC

GND.

SEPARATE 20 AMP GFCI

OUTLET

WHIRLPOOL MOUNTED

AIR SWITCH OR

WALL TIMER

ELECTRICAL INSTALLATION

PUMP/MOTOR

752867-100 Rev. D

ELECTRICAL INSTALLATION INSTRUCTIONS

All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other

applicable codes.

WARNING:

When using electrical products, basic precautions should always be observed, including the following:

1. DANGER: RISK OF ELECTRIC SHOCK

Connect only to a circuit protected by a ground-fault circuit interrupter.

2. Grounding is required. The unit should be installed by a licensed electrician and grounded.

3. Install to permit access for servicing.

4. All building materials and wiring should be routed away from the pump body and heater (if equipped).

The whirlpool should be installed on a 120 vac, 20 amp dedicated circuit. The circuit should be hard-wired from the

electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded

neutral wire and a third wire, earth ground, are essential. ADDING THE E-Z-INSTALL HEATER REQUIRES A

SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT.

(3)

WIRE SELECTION GUIDE

752867-100 Rev. D

DRAIN CONNECTION AND SYSTEM TEST

Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the

pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of

the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings

are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is

connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the

whirlpool is running.

POST INSTALLATION CLEAN-UP

Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.

Do not use wire brushes or any other metal implement on bath surface.

Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or

stains may be removed using granular Spic and Span®mixed with water.

Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.

HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.

Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing

with a white automotive-type polishing compound and waxing with a liquid wax.

Maximum distance from

fusebox to motor The sizes shown on this

chart are recommendations

for copper conductors

only. Always follow

local and national

electrical codes

Motor

Hi Performance

Rating

2.1

50' 100'

120V Power Line

150' 200'

12 10 8 8

(4) SPIC AND SPAN®IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE

Tabla de contenidos

Otros manuales de Bañera de American Standard

American Standard

American Standard Salem 14 0153.015 Manual de usuario

American Standard

American Standard Williamsburg 2908 Series Manual de usuario

American Standard

American Standard 3052OD.0 Series Guía de inicio rápido

American Standard

American Standard ELJER 015-0005 Manual de usuario

American Standard

American Standard Acrylux Builder Series Bathtubs... Manual de usuario

American Standard

American Standard Bath Kit With Walls, Left Drain 6032Y1K.202 Manual de usuario

American Standard

American Standard Heritage 5'x42 Whirlpool 2805.018 Manual de usuario

American Standard

American Standard Evolution 6060VC Manual de usuario

American Standard

American Standard 2549 Manual de usuario

American Standard

American Standard 6030ST3 Manual de usuario

American Standard

American Standard Ellisse Elite 2711EC Manual de usuario

American Standard

American Standard Ellisse Oval Bathtub 2709.XXXW Manual de usuario

American Standard

American Standard Lifetime 2422LA Manual de usuario

American Standard

American Standard Scala Corner 5' 751676-XXX0A Manual de usuario

American Standard

American Standard Standard 2083 SERIES Manual de usuario

American Standard

American Standard Princeton 2390.202 IBS Manual de usuario

American Standard

American Standard 3052OD.X0X Guía de inicio rápido

American Standard

American Standard 1340M Series Instrucciones de funcionamiento

American Standard

American Standard Green Tea 3572.328 Manual de usuario

American Standard

American Standard Williamsburg Elite Whirlpool 2805EC Manual de usuario

American Standard

American Standard Rondo Elite 7242EC Manual de usuario

American Standard

American Standard Princeton 2392.202 ICH Manual de usuario

American Standard

American Standard 2422L / V Instrucciones de funcionamiento

American Standard

American Standard Whirlpool and Bathing Pool 2732.002 Manual de usuario

Manuales populares de Bañera de otras marcas

Agua

Agua BARTOLI-66 Manual de usuario

PAA

PAA PRELUDE Manual de usuario

BETTE

BETTE SILHOUETTE Manual de usuario

Kohler

Kohler K-820-GC Guía de inicio rápido

Oliveri

Oliveri Naples Manual de usuario

Lyons

Lyons Elite ETLxx663219 Series Manual de usuario

Woodbridge

Woodbridge BJ500 Instrucciones de montaje

Whirlpool

Whirlpool Ariel ARL-702 Manual de usuario

TEIKO

TEIKO EXCELLENT DUO Manual de usuario

Kohler

Kohler K-1111-H2 Guía de inicio rápido

agape

agape MARSIGLIA AVAS1075 Manual de usuario

Kohler

Kohler K-1151 Instrucciones de montaje

Kohler

Kohler K-1158 Guía de inicio rápido

Kohler

Kohler K-1244 Instrucciones de montaje

Kallista

Kallista P50045-G5 Instrucciones de montaje

Kohler

Kohler K-1164-HB Guía de inicio rápido

Kohler

Kohler Hourglass K-1209-LA Guía de inicio rápido

Ariel

Ariel AM Series Manual de usuario