Alliance Laundry Systems CTSA9AWN Manual de usuario

Installation Instructions

for Stacked Dryers

Inside ......................................

Dimensions ........................................................................ 3

Before You Start ................................................................ 4

Installing the Dryer ............................................................ 5

Installer Checklist .............................................................. Back Cover

Para bajar una copia de estas instrucciones en espafiol, visite www.speedqueen.com.

Keep these instructions for future reference.

(If this machine changes ownership, this manual must accompany machine.)

Date Purchased

Model Number

Serial Number

www.speedqueen.com

Part No. 512063R3

June 2007

WARNING

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of

fire or explosion or to prevent property damage, personal injury or death. W033

°Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

°WHAT TO DO IF YOU SMELL GAS:

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use any phone in your building.

- Clear the room, building or area of all occupants.

- Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

- If you cannot reach your gas supplier, call the fire department.

•Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance. W053

The following information applies to the state of Massachusetts, USA.

• This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.

• This appliance must be installed with a 36 inch (91 cm) long flexible gas connector.

• A "T-Handle" type gas shut-off valve must be installed in the gas supply line to this appliance.

• This appliance must not be installed in a bedroom or bathroom.

means without the expressed written consent of the publisher.

2© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 512063

Dimensions

23.5 in.

(59.7 cm)

5.25 in.

(13.3 cm)

j lifT',

...... I;%_.j

0.4 in. (1.1 cm)

8.0 in.

(20.3 cm) g

l'l

t *4.5 in.

(11.4 cm)

* With leveling legs turned into base.

° °i..... i° °

(68.3 cm)

ELECTRIC DRYERS

15.4 in.

-(39.1 cm)

15.44 in.

(39.2 cm)

DRY2212N

I_ 23.5 in.

(59.7 cm) --

5.25 in.

(13.3 cm)

i i'

_ S" \\

\¢: e-_,_

28 in.

(71.1 cm)

0.4 in. (1.1 cm)

8.0 in.

(20.3 cm)

*With leveling legs turned into base.

13/8 in. NPT Gas Connection

15.4 in.

(39.1 cm)

2.3 in. "15.44 in.

(6 (39.2 cm)

-- 26.9 in.

(68.3 cm) 1

GAS DRYERS

DRY2213N

512063 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 3

Before You Start

Supplies

For most installations, the basic supplies you will need

are:

DRY2023N

Safety Glasses

Power Cord (Electric Models -2 required)

Wrench

Screwdriver

Level

5/16 Inch Socket Wrench

Duct Tape

Teflon Tape (Gas Models)

Parts Included

An accessories bag has been shipped inside your dryer.

It includes:

• Installation Instructions

• User's Guide

• Product Registration Card

• Warranty Bond

• Three screws (electric dryers only). Refer to

Connecting Power Cord sections in Step 4 of

Installation.

Figure 1

WARNING

Any disassembly requiring the use of

tools must be performed by a suitably

qualified service person. W299

4©Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 512063

Installing the Dryer

Step 1" Position and Level the Dryer

Install dryer before washer. This allows room for

attaching exhaust duct.

Select a location with a solid floor. Dryers installed in

residential garages must be elevated 18 inches (46 cm)

above the floor.

No other fuel burning appliance should be installed in

the same closet with the dryer.

The dryer must not be installed or stored in an area

where it will be exposed to water and/or weather.

The dryers needs sufficient clearance and an adequate

air supply for proper operation and ventilation, and for

easier installation and servicing. (Minimum clearances

are shown below).

A A

FRONT VIEW

i i

SIDE VIEW

ENCLOSURE

DRY2053N

Area Description Closet Installation

A Dryer sides and rear clearance 0 in. (0 cm)

B Dryer top (Rear 24 in.) 12 in. (30.5 cm)

C Dryer rear .4 in. (10.2 cm)

D Dryer Top (Front 4 in.) .5 in. (1.3 cm)

E Exhaust duct clearance to combustible material 2 in. (5.1 cm)

**NOTE: For new installations, locate top of wall vent 42 inches (106.7 cm) above floor to make venting

easier to connect.

Figure 2

512063 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 5

Place the dryer in position, and adjust the legs until the

dryer is level from side to side and front to back. The

dryer must not rock.

Dryer Base

Level

Leveling Leg

DRY2059N

Figure 3

IMPORTANT: In mobile home installations, gas

dryers MUST be permanently attached to the floor

at the time of installation. Order No. 526P3 Dryer

Installation Kit (available at extra cost) for a

manufactured (mobile) home installation. Follow

the instructions supplied with the kit.

Step 2: Connect Dryer Exhaust System

WARNING

To reduce the risk of fire and combustion

gas accumulation the dryer MUST be

exhausted to the outdoors. W604

To reduce the risk of fire and the

accumulation of combustion gases, DO NOT

exhaust dryer air into a window well, gas

vent, chimney or enclosed, unventilated

area, such as an attic, wall, ceiling, crawl

space under a building or concealed space

of a building. W045

WARNING

This gas appliance contains or produces a

chemical or chemicals which can cause

death or serious illness and which are

known to the State of California to cause

cancer, birth defects, or other reproductive

harm. To reduce the risk from substances in

the fuel or from fuel combustion, make sure

this appliance is installed, operated, and

maintained according to the instructions in

this manual.

Wl15

To reduce the risk of fire, DO NOT use

plastic or thin foil ducting to exhaust the

dryer. W354

•DO NOT use plastic or thin foil ducting. Rigid

metal duct is recommended.

L!Li i

Y//////////////////////,,

DON'T

DRY2010N

Figure 4

•Locate dryer so exhaust duct is as short as

possible.

• Be certain old ducts are cleaned before installing

your new dryer.

• Use 4 inch (102 mm) diameter rigid or flexible

metal duct.

• The male end of each section of duct must point

away from the dryer.

• Use as few elbows as possible.

• Use duct tape or pop-rivets on all duct joints.

• Ductwork that runs through unheated areas must

be insulated to help reduce condensation and lint

build-up on pipe walls.

6 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 512063

• In mobile home installations, dryer exhaust duct

must be secured to mobile home structure.

• Dryer exhaust duct MUST NOT terminate under

mobile home.

Dryer exhausts 220 cfm (measured at back of

dryer).

Static pressure in exhaust duct should not be

greater than .6 inches water column (1.5 cm),

measured with manometer placed on exhaust

duct two feet (61 cm) from dryer (check with

dryer running and no load).

Exhausting dryer in hard-to-reach locations can

be done by installing 521 P3 Flexible Metal Vent

Kit (available as optional equipment at extra

cost).

Failure to exhaust dryer properly will void

warranty.

NOTE: Venting materials are not supplied with the

dryer (obtain locally).

Exhaust Direction

The dryer can be exhausted to the outdoors through the

back, left, right or bottom of the dryer. EXCEPTION:

Gas dryers cannot be vented out the left side

because of the burner housing.

Dryer is shipped from factory ready for rear exhaust.

Exhausting the dryer through sides or bottom can be

accomplished by installing a Directional Exhaust Kit,

528P3, available as optional equipment at extra cost.

Exhaust System

For best drying results, recommended maximum

length of exhaust system is shown in Table 1.

To prevent backdraft when dryer is not in operation,

outer end of exhaust pipe must have a weather hood

with hinged dampers (obtain locally).

NOTE: Weather hood should be installed at least

12 inches (30.5 cm) above the ground. Larger

clearances may be necessary for installations where

heavy snowfall can occm:

Number of Weather Hood Type

90° Elbows Recommended Use Only for Short Run installations

4 in. 4 in.

(10.2 cm) (10.2 cm)

D6731

0 feet (13.7 m)

1 feet (10.7 m)

2 feet (9.1 m)

3 feet (7.6 m)

4 20 feet (6.1 m)

NOTE: Deduct 6 feet (1.8 m) for each additional elbow.

Table 1

2-1/2 in.

(6.35 cm)

Maximum length of 4 in. (10.2 cm)diameter rigid metal duct.

0 65 feet (19.8 m) 55 feet (16.8 m)

1 55 feet (16.8 m) 47 feet (14.3 m)

2 47 feet (14.3 m) 41 feet (12.5 m)

3 36 feet (11.0 m) 30 feet (9.1 m)

4 28 feet (8.5 m) 22 feet (6.7 m)

Maximum length of 4 in. (10.2 cm) diameter flexible metal duct.

45 35 feet (10.7 m)

35 27 feet (8.2 m)

30 21 feet (6.4 m)

25 17 feet (5.2 m)

15 feet (4.5 m)

D8021

512063 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 7

Step 3: (Gas Dryer Only) Connect Gas

Supply Pipe

WARNING

To reduce the risk of gas leaks, fire or

explosion:

•The dryer must be connected to the type

of gas as shown on nameplate located in

the door recess.

•Use a new flexible stainless steel

connector.

•Use pipe joint compound insoluble in L.P.

(Liquified Petroleum) Gas, or Teflon tape,

on all pipe threads.

•Purge air and sediment from gas supply

line before connecting it to the dryer.

Before tightening the connection, purge

remaining air from gas line to dryer until

odor of gas is detected. This step is

required to prevent gas valve

contamination.

•Do not use an open flame to check for gas

leaks. Use a non-corrosive leak detection

fluid.

•Any disassembly requiring the use of

tools must be performed by a suitably

qualified service person. W316

.Make certain your dryer is equipped for use with

the type of gas in your laundry room. Dryer is

equipped at the factory for Natural Gas with a

3/8 inch NPT gas connection.

NOTE: The gas service to a gas dryer must

conform with the local codes and ordinances, or in

the absence of local codes and ordinances, with the

latest edition of the National Fuel Gas Code ANSI

Z223.1/NFPA 54 or the CAN/CGA-B149, National

Gas Installation Code.

Natural Gas, 1000 Btu/ft 3 (37.3 MJ/m 3) service must

be supplied at 6.5 + 1.5 inch water column pressure.

For proper operation at altitudes above 3000 feet

(915 m) the natural gas valve spud orifice size must be

reduced to ensure complete combustion. Refer to

Table 2.

Natural Gas Altitude Adjustments

Altitude

feet m

3000 915

6000 1830

8000 2440

9000 2740

10,000 3050

Orifice Size

No. inches mm

43 0.0890 2.26

44 0.0860 2.18

45 0.0820 2.08

46 0.0810 2.06

47 0.0785 1.99

Table 2

Part No.

503778

58719

503779

503780

503781

Remove the shipping cap from the gas

connection at the rear of the dryer. Make sure you

do not damage the pipe threads when removing

the cap.

3. Connect to gas supply pipe.

NOTE: When connecting to a gas line, an

equipment shut-off valve must be installed within

6 feet (1.8 m) of the dryel. An 1/8 in. NPT pipe plug

must be installed as shown for checking inlet

pressure. Refer to Figure 5.

D6991

New stainless steel flexible connector -

(Use design CSA certified connector)

Use only if allowed by local codes

1/8 in. NPT Pipe Plug

Equipment Shut-Off Valve

Black Iron Pipe Shorter than 20 ft. (6.1 m) -

Use 3/8 in. (9.5 mm) pipe

3/8 in. NPT Gas Connection

Figure 5

8 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 512063

.Tighten all connections securely. Turn on gas and

check all pipe connections (internal & external)

for gas leaks with a non-corrosive leak detection

fluid.

NOTE: The dryer and its appliance main gas valve

must be disconnected from the gas supply piping

system during any pressure testing of that system

at test pressures in excess of 1/2 psi (3.45 kPa).

Refer to Step 8 (Check Heat Source).

L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft 3

(93.1 MJ/m 3) service must be supplied at 10 + 1.5 inch

water column pressure.

For proper operation at altitudes above 3000 feet (915 m)

the L.R gas valve spud orifice size must be reduced to

ensure complete combustion. Refer to Table 3.

L.P. Altitude Adjustments

Altitude

feet m

3000 915

8000 2440

Orifice Size

No. inches mm

55 0.0520 1.32

56 0.0465 1.18

Table 3

Part No.

58755

503786

NOTE: DO NOT connect the dryer to L.P. Gas

Service without converting the gas valve. Install

L.P. Gas Conversion Kit 649P3, available at extra

cost.

Step 4: (Electric Dryer Only) Connect

Electrical Plug

Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz,

3 or 4 wire electrical suppy. Refer to serial plate for

specific electrical requirements.

NOTE: The wiring diagram is located behind the

control panel, inside the control cabinet.

WARNING

To reduce the risk of fire, electric shock,

serious injury or death, all wiring and

grounding MUST conform with the latest

edition of the National Electrical Code,

ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1, and such local

regulations as might apply. It is the

customer's responsibility to have the wiring

and fuses installed by a qualified electrician

to make sure adequate electrical power is

available to the dryer. W521

Grounding Information

This dryer must be connected to a grounded

metal, permanent wiring system; or an

equipment-grounding conductor must be run

with the circuit conductors and connected to the

equipment-grounding terminal or lead on the

dryer.

The dryer has its own terminal block that must be

connected to a separate branch, 60 Hertz, single

phase circuit, AC (alternating current) circuit,

fused at 30 Amperes (the circuit must be fused

on both sides of the line). Electrical service for

the dryer should be of maximum rated voltage

listed on the nameplate. Do not connect dryer

to 110, 115, or 120 volt circuit.

Heating elements are available for field

installation in dryers which are to be connected to

electrical service of different voltage than that

listed on nameplate, such as 208 Volt.

If branch circuit to dryer is 15 feet (4.57 m) or

less in length, No. 10 AWG wire (copper wire

only), or as required by local codes. If over 15

feet (4.57 m), use No. 8 AWG wire (copper wire

only), or as required by local codes. Allow

sufficient slack in wiring so dryer can be moved

from its normal location when necessary.

The power cord connection between wall

receptacle and dryer terminal block IS NOT

supplied with dryeL Type of power cord and

gauge of wire must conform to local codes.

Connecting Power Cord with Three-Wire Plug

NOTE: Four-wire cord is required for mobile

homes or where codes do not permit grounding

through neutral.

NOTE: The power cord is NOT supplied with the

electric dryer. Type of power cord and gauge of wire

must conform to local codes and instructions. POWERSUPPLY POWER SUPPLY

The method of wiring the dryer is optional and subject

to local code requirements.

NOTE: Connect the dryer to the power supply with the

MAXIMUM RATED VOLTAGE listed on the nameplate.

120 -+

V.A.C.

A typical

30-Amp

Three-Wire

Receptacle

NEMAType

10-30R

±12

V.A.C.

INTERMEDIATE

FUSE BOX (may

be omitted if

service entrance

box is fused)

WALL

RECEPTACLE

NOTE: Use COPPER WIRE only.

Shorter than 15 ft. (4.5 m) - use 10 AWG

Longer than 15 ft. (4.5 m) - use 8 AWG

INTERMEDIATE

SHUT-OFF BOX

(may or may not

be fused)

41._._......- 7_

L1 L2 L1 L2

POWER CORD CONNECTION DIRECT CONNECTION

3 Wire Grounded Neutral 120/240 Volt, 60 Hertz

AC 1 Phase Service Entrance Switch Box

(Refer to NOTE above)

30 Ampere Fuses or Circuit Breaker

Neutral Wire

Metallic or Non-Metallic Sheathed Cable

(Copper Wire Only)

Power Cord (Not supplied with dryer)

Neutral

Terminal Block in Dryer

D8161

1. Disconnect power to dryer.

2. Remove access cover from rear of dryer.

Figure 6

3. Use a strain relief and insert end of power cord

through power supply hole.

Figure 7

D6951 Figure 8

D6961

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Secadora de Alliance Laundry Systems

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen FF7009WN Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems SWD439C Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems UT025 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems LTS87A*H Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems D715I Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems DR5000WG Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems DC5102WE Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems T453I Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems 70420801 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems DR3000WG Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems CA050L Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems D355IE1B Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems Dryer Tumblers Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Clothes dryers Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 907003062 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems JT30XG Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems 25 Pound Capacity Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems DRY724C_SVG Guía

Alliance Laundry Systems

Alliance Laundry Systems CA120L Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems LGS19A-1188 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LES33AW Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems D677I_SVG Instrucciones de funcionamiento originales

Alliance Laundry Systems

Alliance Laundry Systems BD3LLFGS401UW01 Instrucciones de funcionamiento

Manuales populares de Secadora de otras marcas

Bosch

Bosch WTA79200GB Manual de usuario

Amana

Amana W10233410A Manual de usuario

Miele

Miele TWH 780 WP Manual de usuario

Asko

Asko T760 Manual de usuario

Bosch

Bosch Logixx 10 WTB76556GB Hoja de especificaciones

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manual de instrucciones

Electrolux

Electrolux EW2H328R2 Manual de usuario

Beko

Beko DS8433RX1M Manual de usuario

Dawlance

Dawlance Spinner DS 6000 C Manual de usuario

Electrolux

Electrolux TP5080TW Manual de usuario

AEG

AEG TR838P4OB Manual de usuario

Indesit

Indesit IDV 75 Manual de usuario

Infiniton

Infiniton SD-DG85C Manual de usuario

BOMANN

BOMANN WT 5019 Manual de usuario

Asko

Asko T793C Manual de usuario

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario

Frigidaire

Frigidaire CAQE7077KW0 Manual del propietario

Bosch

Bosch WTX8HKM9SN Manual de usuario