Agilent Technologies 81250 Manual de usuario

Agilent Parallel Bit Error Ratio Tester

81250 ParBERT

Installation Guide

Agilent Technologies

Important Notice

Manual Part Number

81250-91010

Revision

Revision 3.0, May 2004

Printed in Germany

Agilent Technologies,

Deutschland GmbH

Herrenberger Str. 130

71034 Boeblingen, Germany

Authors: t3 medien GmbH

Warranty

The material contained in this

document is provided “as is,” and is

subject to being changed, without

notice, in future editions. Further, to

the maximum extent permitted by

applicable law, Agilent disclaims all

warranties, either express or

implied, with regard to this manual

and any information contained

herein, including but not limited to

the implied warranties of

merchantability and fitness for a

particular purpose. Agilent shall not

be liable for errors or for incidental

or consequential damages in

connection with the furnishing, use,

or performance of this document or

of any information contained herein.

Should Agilent and the user have a

separate written agreement with

warranty terms covering the

material in this document that

conflict with these terms, the

warranty terms in the separate

agreement shall control.

Technology Licenses

The hardware and/or software

described in this document are

furnished under a license and may

be used or copied only in

accordance with the terms of such

license.

Restricted Rights Legend

If software is for use in the

performance of a U.S. Government

prime contract or subcontract,

Software is delivered and licensed

as “Commercial computer software”

as defined in DFAR 252.227-7014

(June 1995), or as a “commercial

item” as defined in FAR 2.101(a) or

as “Restricted computer software”

as defined in FAR 52.227-19 (June

1987) or any equivalent agency

regulation or contract clause. Use,

duplication or disclosure of

Software is subject to Agilent

Technologies’ standard commercial

license terms, and non-DOD

Departments and Agencies of the

U.S. Government will receive no

greater than Restricted Rights as

defined in FAR 52.227-19(c)(1-2)

(June 1987). U.S. Government users

will receive no greater than Limited

Rights as defined in FAR 52.227-14

(June 1987) or DFAR 252.227-7015

(b)(2) (November 1995), as

applicable in any technical data.

Safety Notices in the Manual

CAUTION

A CAUTION notice denotes a

hazard. It calls attention to an

operating procedure, practice, or the

like that, if not correctly performed

or adhered to, could result in

damage to the product or loss of

important data. Do not proceed

beyond a CAUTION notice until the

indicated conditions are fully

understood and met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or the

like that, if not correctly performed

or adhered to, could result in

personal injury or death. Do not

proceed beyond a WARNING notice

until the indicated conditions are

fully understood and met.

Trademarks

MS Windows, Windows NT,

Windows 2000, Windows XP are

trademarks of Microsoft

Corporation.

Safety Symbols on Instruments

If you see this symbol on a product,

you must refer to the manuals for

specific WARNING or CAUTION

information to avoid personal injury

or damage of the product.

Indicates the protective conductor

terminal that must be connected to

Protective Earth before operating

the equipment. Protects against

electrical shock in case of fault.

Indicates hazardous voltages and

potential for electrical shock.

Indicates that antistatic precautions

should be taken.

Notice for European Community:

This is an Industrial, Scientific, and

Medical (ISM) Group 1 Class A

product that complies with the

relevant European legal directives:

EMC Directive 89/336/EEC and Low

Voltage Directive 73/23/EEC.

Indicates invisible and potentially

hazardous laser radiation.

Agilent 81250 ParBERT Installation Guide, May 2004 Contents-1

Contents

1 About this Manual 1-1

Welcome to the ParBERT Installation Guide 1-2

General Structure of the Installation Guide 1-2

How to Use this Guide 1-3

Document History 1-5

2 Introduction 2-1

ParBERT Components Overview 2-1

The ParBERT Controller PC 2-2

The ParBERT Mainframes 2-3

The ParBERT Modules 2-4

About ParBERT Systems 2-11

ParBERT Software Components 2-14

Prerequisites 2-15

Power Supply 2-15

Environment 2-15

Controller PC Requirements 2-16

Tools 2-16

Unpacking ParBERT 2-17

3 Setting Up the ParBERT Controller PC 3-1

Setting up a Preconfigured Controller PC 3-1

Quick Check 3-2

Configuration of the Operating System 3-2

Contents

Contents-2 Agilent 81250 ParBERT Installation Guide, May 2004

Setting Up a Custom Controller PC 3-3

Installing the Agilent I/O Libraries 3-4

Installing the Interface Cards 3-5

Enabling the Interfaces 3-6

4 Connecting Mainframes to the Controller PC 4-1

Checking the Mainframe Clock Distribution 4-2

Connecting the Master Mainframe 4-4

Connecting Expander Mainframes 4-5

Interconnecting Slave Mainframes 4-6

Positioning the Mainframes 4-7

Installing the Synchronization Cable in a Slave 4-8

Connecting the Synchronization Cables to the Master 4-9

Connecting the Clock Reference Cables 4-11

Connecting the Giga Clock 4-13

5 Putting ParBERT into Operation 5-1

How to Configure the IEEE 1394 and GPIB Interfaces 5-2

How to Install the ParBERT User Software 5-6

How to Use the Agilent 81250 Config Tool 5-7

How to Configure I/O Interfaces and Systems 5-9

How to Check the Configuration and Serial Numbers 5-12

How to Specify Startup Settings 5-14

How to Configure SICL/LAN Interfaces 5-17

Starting the ParBERT User Software 5-18

How to Select the Firmware Server 5-20

How to Select the System 5-21

How to Specify a Start Setting 5-22

Contents

Agilent 81250 ParBERT Installation Guide, May 2004 Contents-3

How to Disable the UI Configuration Dialog 5-23

How to Get Help 5-24

Testing ParBERT’s Integrity 5-25

6 Changing the ParBERT Hardware 6-1

Removing a Module 6-2

How to Disconnect the Module Cables 6-2

How to Plug Out the Module 6-3

Installing a Module 6-4

How to Set the Logical Address 6-5

How to Plug In the Module 6-7

How to Connect the Module 6-8

How to Open a Module 6-12

Adding or Changing Frontends 6-13

How to Remove a Frontend 6-15

How to Install a Frontend 6-18

Installing the Trigger Input Pod 6-20

How to Proceed After Changing the Hardware 6-22

7 Special ParBERT Systems 7-1

Installing ParBERT 43/45G Systems 7-1

Components of ParBERT 43/45G Systems 7-2

Setting up ParBERT 43/45G Systems 7-4

Converting ParBERT 43/45G to a Basic ParBERT 7-6

ParBERT 43/45G Extensions 7-9

Making Clock Connections 7-11

Installing Optical Modules 7-14

Laser Safety Information 7-14

Contents-4 Agilent 81250 ParBERT Installation Guide, May 2004

Installing E4810A/E4811A Electrical-Optical Modules 7-16

Installing E4882A O/E and E4883A E/O Converter Modules7-19

Installing the 10.8 Gbit/s Booster Module 7-21

Expanding Systems with Embedded Controller 7-23

8 Troubleshooting the ParBERT Installation 8-1

Problems at the Power-On Selftest 8-1

Problems after Changing the Hardware 8-2

Problems with Clockgroups 8-4

9 Controlling ParBERT Remotely 9-1

Controlling ParBERT via GPIB 9-1

Controlling ParBERT via LAN 9-3

Appendix 10-1

Declaration of Conformity 10-2

Site Attenuation Requirements 10-5

Agilent 81250 ParBERT Installation Guide, May2004 1-1

1 About this Manual

ParBERT is the term for Agilent Technologies’ family of Parallel Bit Error

Ratio Testers.

Agilent 81250 ParBERT is a modular parallel electrical and optical bit

error rate (BER) test platform that operates at up to 45 Gbit/s. The

ParBERT 81250 platform comprises modules that operate at 675 Mbit/s,

1.65 Gbit/s, 2.7 Gbit/s, 3.35 Gbit/s, 7 Gbit/s, 10.8 Gbit/s, 13.5 Gbit/s, and

45 Gbit/s.

The system generates pseudo random word sequences (PRWS), standard

pseudo random binary sequences (PRBS) and user-defined patterns on

parallel lines. You can analyze bit error ratios with user defined patterns,

PRBS/PRWS, or mixed data (a combination of user-defined patterns and

PRBS).

This installation guide leads you through the steps to identify, install, and

configure the Agilent 81250 ParBERT or any component of this system.

1 About this Manual Welcome to the ParBERT Installation Guide

1-2 Agilent 81250 ParBERT InstallationGuide, May 2004

Welcome to the ParBERT

Installation Guide

This manual is not only the guide for the first-time installation. It

contains also the necessary instructions if you wish to change or upgrade

an existing ParBERT configuration.

General Structure of the Installation Guide

The chapters two to five provide all the information you need for setting

up a standard, multi-purpose ParBERT system. This is a system

consisting of a controller PC and one to three VXI mainframes that

contain clock modules and electrical data generator/analyzer modules.

Chapter six explains how you can change the hardware configuration of

an existing ParBERT system.

Chapter seven deals with special ParBERT systems. These are systems

containing special components or modules for special purposes. Such

modules are, for example, the MUX/DEMUX modules of 43/45 Gbit/s

systems, optical modules, the 10.8 Gbit/s Booster Module, or the

embedded ParBERT controller (a PC built up as a 2-slot VXI module).

Chapter eight provides assistance if you have changed the hardware and

the system does not react as expected.

The last chapter gives some advice about how to set up ParBERT for

remote control.

Basics

Hardware changes

Special systems

Troubleshooting

Remote control

Welcome to the ParBERT Installation Guide 1 About this Manual

Agilent 81250 ParBERT Installation Guide, May2004 1-3

How to Use this Guide

This manual is not meant to be read through from its beginning to its

end. It depends on your situation which information you need.

If … … refer to Chapter Chapter contents

… you install ParBERT for

the first time “2 Introduction” on

page 2-1 This chapter provides an overview of the standard

system components and the prerequisites for the

installation.

… you have received a new

ParBERT system “3 Setting Up the

ParBERT Controller

PC” on page 3-1

ParBERT requires a controller PC. This chapter

provides information on:

• How to start a preconfigured ParBERT controller

• How to install the ParBERT hard- and software

on a custom PC

•

… you wish to connect one

or several ParBERT

mainframes

“4 Connecting

Mainframes to the

Controller PC” on

page 4-1

This chapter provides instructions on how to connect

a single or multiple ParBERT mainframes through IEEE

1394 PC link to VXI interfaces.

If you wish to add mainframes to a ParBERT system

with embedded controller PC (a special VXI module),

refer to chapter “Expanding Systems with Embedded

Controller” on page 7-23.

… you are starting

ParBERT for the first time,

or if you have changed the

hardware configuration

“5 Putting ParBERT

into Operation” on

page 5-1

This chapter explains how to check the hardware

identification and how to use the ParBERT

Configuration tool.

… you wish to add,

exchange, or remove

modules or frontends

“6 Changing the

ParBERT Hardware”

on page 6-1

This chapter contains all the necessary information.

1 About this Manual Welcome to the ParBERT Installation Guide

1-4 Agilent 81250 ParBERT InstallationGuide, May 2004

If … … refer to Chapter Chapter contents

… your system includes

special modules “7 Special ParBERT

Systems” on page 7-1 In this chapter, you find the supplementary

• installation instructions for 43/45 Gbit/s systems

• installation instructions for optical modules

• installation instructions for the 10.8 Gbit/s

Booster Module

• upgrade instructions for ParBERT systems with

embedded controller PC

… your installation was not

successful “8 Troubleshooting

the ParBERT

Installation” on

page 8-1

This chapter provides information on frequent

problems, possible causes, and solutions.

… you wish to control

ParBERT from a remote

computer

“9 Controlling

ParBERT Remotely”

on page 9-1

Though remote control via GPIB is possible, the

preferred method is via LAN. This chapter explains

how to set up ParBERT for remote control.

Several optional as well as standard system components are delivered

with their own dedicated installation and user manuals. Such

components are for example:

• E8403A/E8404A VXI mainframe

• E9850A embedded VXI controller

• E8491B IEEE 1394 PC link to VXI

• VXI bus extenders

Before you start with the installation, it is therefore recommended that

you inspect the shipment for additional documentation that may be

required for a successful setup and installation.

For latest information, answers on frequently asked questions, and

related documentation, please check the following URL:

http://www.agilent.com/find/parbert

To contact the ParBERT support via e-mail, use the following address:

[email protected]

NOTE

Internet

Otros manuales para 81250

Tabla de contenidos

Otros manuales de Equipo de prueba de Agilent Technologies

Agilent Technologies

Agilent Technologies InfiniiVision 5000 Series Manual

Agilent Technologies

Agilent Technologies N4413A Manual de usuario

Agilent Technologies

Agilent Technologies N9360A Manual de usuario

Agilent Technologies

Agilent Technologies E6630A Manual de usuario

Agilent Technologies

Agilent Technologies 4072A Advanced Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Manual

Agilent Technologies

Agilent Technologies 16034E Manual de operación

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X- Series Manual del operador

Agilent Technologies

Agilent Technologies 85050C Manual

Agilent Technologies

Agilent Technologies Infiniium 9000 Series Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 7000B Series Manual de usuario

Agilent Technologies

Agilent Technologies 1000A Series Manual de usuario

Agilent Technologies

Agilent Technologies E4406A VSA Series Manual

Agilent Technologies

Agilent Technologies aurora Duet Manual de usuario

Agilent Technologies

Agilent Technologies 54610B Manual

Agilent Technologies

Agilent Technologies E6621A Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 4000 X-Series Manual

Agilent Technologies

Agilent Technologies 5DX II Series Manual de usuario

Agilent Technologies

Agilent Technologies 85110L Manual

Agilent Technologies

Agilent Technologies E7474A Manual de usuario

Agilent Technologies

Agilent Technologies N5230AU-974 Manual de instalación y operación

Agilent Technologies

Agilent Technologies InfiniiVision 6000 Series Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 7000A Series Manual

Agilent Technologies

Agilent Technologies InfiniiVision 2000 X-Series Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manual de usuario

Ritmix

Ritmix RAT-701 Manual de usuario