Agilent Technologies 54610B Manual

User and

Service Guide

Publication number 54610-97018

August 2000

For Safety nformation, Warranties, and Regulatory information,

see the pages behind the index.

Agilent 54610B

Oscilloscope

A General-Purpose Oscilloscope

The Agilent 54610B oscilloscope offers exceptional waveform

viewing and measurements in a small, lightweight package. This dual

channel,

500 MHz bandwidth oscilloscope is designed for use in labs where

high speed analog and digital circuits are being tested. This

oscilloscope gives you:

•500 MHz bandwidth, and 1 ns/div Main and Delayed time bases

•Selectable input impedance

•Protection of the internal 50 ohm load

•Adjustable time nulling to remove the effects of cabling

•Repetitive waveform sampling at up to 10 GSa/sec

(20 MSa/sec single shot)

•Viewable external trigger input

This oscilloscope is very easy to use because of its familiar controls

and real time display. You can discard your viewing hood as this

oscilloscope has none of the viewing problems that are associated

with analog oscilloscopes. A bright, crisp display is obtained at all

sweep speeds and delayed sweep magnifications. Storage is as

simple as pressing a button. View events ahead of the trigger using

negative time. Cursors and automatic measurements greatly simplify

your analysis tasks.

You can upgrade this oscilloscope for hardcopy or remote control

with the addition of an interface module. Unattended waveform

monitoring and additional waveform math, such as FFT, can be

added with the addition of one of the Measurement/Storage modules.

Bring your scope and PC together with BenchLink software.

BenchLink, which runs under Windows, allows the easy transfer of

scope traces and waveform data to your PC for incorporation into

documents or storage.

Accessories supplied

•Two 1.5 meter, 10:1 Rugged 500 MHz Probes (10073B)

•Power cord for country of destination

•This User and Service Guide

Accessories available

•34810B BenchLink Software

•54650A GP B nterface Module

•54652B /Parallel/RS-232 nterface Module

•54654A Operator’s Training Kit

•54657A and Agilent 54659B Measurement/Storage Modules

•1185A Carrying Case

•1186A Rackmount Kit

•10070B 1.5 meter, 1:1 Probe

•10020A Resistive Divider Probe Kit

iii

Options available

•Option 001 RS-03 Magnetic nterference Shielding Added to CRT

•Option 002 RE-02 Display Shield Added to CRT

•Option 005 Enhanced TV/Video Trigger

•Option 101 Accessory Pouch and Front-Panel Cover

•Option 103 Operator’s Training Kit (54654A)

•Option 104 Carrying Case (1185A)

•Option 106 BenchLink Software (34810B)

•Option 090 Deletes Probes

•Option 908 Rackmount Kit (1186A)

•Power Cords (see the table of Replaceable Parts in chapter 3,

Service)

In T is Book

This book is the operating and service manual for the Agilent 54610B

oscilloscope, and contains four chapters.

First Time Users Chapter 1 is a quick start guide that gives you a brief

overview of the oscilloscope.

Advanced users Chapter 2 is a series of exercises that guide you

through the operation of the oscilloscope.

Service technicians Chapter 3 contains the service information for the

oscilloscope. There are procedures for verifying performance,

adjusting, troubleshooting, and replacing assemblies in the oscilloscope.

Reference information Chapter 4 lists the characteristics of the

oscilloscope.

Contents

1 The Oscilloscope at a Glance

To connect a signal to the oscilloscope 1–5

To display a signal automatically 1–7

To set up the vertical window 1–8

To set up the time base 1–10

To trigger the oscilloscope 1–12

To use roll mode 1–15

2 Operating Your Oscilloscope

To use delayed sweep 2–3

To use storage oscilloscope operation 2–6

To capture a single event 2–8

To capture glitches or narrow pulses 2–10

To trigger on a comple waveform 2–12

To make frequency measurements automatically 2–14

To make time measurements automatically 2–16

To make voltage measurements automatically 2–19

To make cursor measurements 2–23

To remove cabling errors from time interval measurements 2–27

To make setup and hold time measurements 2–28

To view asynchronous noise on a signal 2–29

To reduce the random noise on a signal 2–31

To analyze video waveforms 2–34

To save or recall traces 2–38

To save or recall front-panel setups 2–39

To use the XY display mode 2–40

3Service

To return the oscilloscope to Agilent Techologies 3–4

Verifying Oscilloscope Performance 3–5

To check the output of the DC CALIBRATOR 3–6

To verify voltage measurement accuracy 3–7

Contents-1

To verify bandwidth 3–10

To verify horizontal ∆t and 1/∆t accuracy 3–14

To verify trigger sensitivity 3–17

Adjusting the Oscilloscope 3–21

To adjust the power supply 3–22

To perform the self-calibration 3–24

To adjust the high-frequency pulse response 3–26

To adjust the display 3–28

Troubleshooting the Oscilloscope 3–30

To construct your own dummy load 3–31

To check out the oscilloscope 3–32

To check the LVPS (Low Voltage Power Supply) 3–35

To run the internal self-tests 3–36

Replacing Parts in the Oscilloscope 3–39

To replace an assembly 3–40

To remove the handle 3–45

To order a replacement part 3–45

4 Performance Characteristics

Vertical System 4–2

Horizontal System 4–4

Trigger System 4–5

XY Operation 4–6

Display System 4–6

Acquisition System 4–7

Advanced Functions 4–8

Power Requirements 4–8

General 4–9

Glossary

In ex

Contents

Contents-2

The Oscilloscope at a Glance

One of the first things you will want to do with your new oscilloscope

is to become acquainted with its front panel. Therefore, we have

written the exercises in this chapter to familiarize you with the

controls you will use most often.

The front panel has knobs, grey keys, and white keys. The knobs are

used most often and are similar to the knobs on other oscilloscopes.

The grey keys bring up softkey menus on the display that allow you

access to many of the oscilloscope features. The white keys are

instant action keys and menus are not associated with them.

Throughout this book, the front-panel keys are denoted by a box

around the name of the key, and softkeys are denoted by a change in

the text type. or example, Source is the grey front-panel key

labeled Source under the trigger portion of the front panel, and

Line is a softkey. The word Line appears at the bottom of the

display directly above its corresponding softkey.

igure 1-1 is a diagram of the front panel controls and input

connectors.

igure 1-2 is a status line example. The status line, located at the top

of of the display, lets you quickly determine the setup of the

oscilloscope. In this chapter you will learn to read at a glance the

setup of the oscilloscope from the status line.

igure 1-3 is a diagram showing which grey keys to press to bring up

the various softkey menus.

1-2

Tabla de contenidos

Otros manuales de Equipo de prueba de Agilent Technologies

Agilent Technologies

Agilent Technologies 85052B Manual

Agilent Technologies

Agilent Technologies 8922M Manual de usuario

Agilent Technologies

Agilent Technologies 11645A Series Manual

Agilent Technologies

Agilent Technologies Medalist i3070 Series 5i Manual

Agilent Technologies

Agilent Technologies 8960 Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies 54522A Manual de usuario

Agilent Technologies

Agilent Technologies 85054D Manual

Agilent Technologies

Agilent Technologies E2969A Manual de usuario

Agilent Technologies

Agilent Technologies 90000 X Series Manual de usuario

Agilent Technologies

Agilent Technologies E7495A RF Manual de instrucciones

Agilent Technologies

Agilent Technologies E5091A Manual de usuario

Agilent Technologies

Agilent Technologies 85056A Manual

Agilent Technologies

Agilent Technologies Infiniium 90000 A Manual de usuario

Agilent Technologies

Agilent Technologies 54810A Manual de usuario

Agilent Technologies

Agilent Technologies U1452A Manual de usuario

Agilent Technologies

Agilent Technologies N9360A Manual del propietario

Agilent Technologies

Agilent Technologies 8920B Manual de usuario

Agilent Technologies

Agilent Technologies 54621A Manual de usuario

Agilent Technologies

Agilent Technologies 86100A Cómo utilizar

Agilent Technologies

Agilent Technologies 5530 Manual de usuario

Agilent Technologies

Agilent Technologies U1604A Manual de usuario

Agilent Technologies

Agilent Technologies Ininiium 90000 Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision MSO6104A Guía de inicio rápido

Agilent Technologies

Agilent Technologies Medalist x6000 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manual de usuario

Ritmix

Ritmix RAT-701 Manual de usuario