Agilent Technologies G6600 Guía

Purpose

The Brass Burner has two ceramic combustion tubes which require periodic

replacement: an inner and an outer tube.

Scope

This procedure applies to ceramic tube replacement in the Agilent Instruments

ABI 00003 Brass Burner.

Tools

•2 - 1/16” Open End Wrenches

•2 - 3/8” Open End Wrenches

•2 - 7/16” Open End Wrenches

Procedure

1. Turn off the Interface Controller and let the system cool down under

vacuum.

The Burner is extremely hot when running. Do not touch the burner until it has

cooled down.

2. Turn off the vacuum pump.

3. Remove the hydrogen line by disconnecting the Hydrogen Inlet Fitting at

the top of the Burner. Use a second wrench to hold the Adapter Tee to

avoid excess torque on the ceramic tubes.

4. Disconnect the black PFA transfer line from the Tee of the Burner

Interface.

5. Unscrew the Tee fitting and carefully pull the inner Tube/Tee assembly

from the Burner. If the existing Tube is broken then all fragments must

be removed from the burner.

Note

Ceramic Probe Replacement

Instructions

Accessory G6600-60034

6. Remove the ferrule attached to the top of the 1/8” ceramic tube.

7. Disconnect the Heater Cable from the heating element leads.

The heating element leads are very fragile. Do not bend them excessively or they

will be damaged.

8. Disconnect the thermocouple leads from the Interface Controller.

9. Remove the four horizontal socket head cap screws holding the Burner

Case.

10. Carefully lift the Burner Case up off of the base and set it aside.

11. Remove the white insulating disk and the fiber insulating toroid from the

Burner base.

12. Remove the 1/8” ceramic tube by loosening the nut in the Burner base.

Discard the used ceramic tube and ferrule. Remove any debris from the

inside of the connection.

Screw extractors may be useful in removing old ferrules from Burner fittings.

Note

13. Insert the new 1/8” ceramic tube into the fitting with a new Vespel

ferrule. Slide the nut over the tube and tighten it until finger tight. Lift

the ceramic tube up 1 to 2 mm so that it will not be crushed by the

compression fitting. Tighten the nut snugly with the 7/16” wrench. This

connection must be fairly tight to ensure that the nut does not loosen

under heat stress, but excessive tightening can crack the ceramic tube.

14. Reinstall the fiber insulating toroid and the white insulating disk.

Carefully slide the Burner Cover over the large ceramic tube. It is often

useful to sight down the upper fitting to ensure that the ceramic tube is

properly aligned and will not break.

Failure to install the insulating disk may lead to leaks in the Burner.

15. Reinstall the four screws at the base of the Burner.

16. Unscrew the Hydrogen Inlet fitting from the Tee, and remove the 1/16"

tube and ferrule.

Note

17. Install a new 1/16" Vespel ferrule at the top of the Tee. Slide in a new

inner ceramic tube until approximately 1/8" (2 mm) extends out of the

top of the ferrule Retighten the Hydrogen Inlet fitting snugly. Do not

overtighten the fitting.

18. Replace the Tube and Tee assembly into the Burner, tightening finger

tight.

19. Check the flow of air and hydrogen following the Detector manual

instructions.

20. Reconnect the Heater Cable, Thermocouple, and all the tubing. Pressure

test the system following the instructions in the Detector manual. The

pressure may change slightly due to variation in tube dimensions.

21. Turn on the Interface Controller and allow the Burner temperature to

stabilize. Gently tighten all the fittings once the Burner temperature is

stable.

Agilent Technologies, Inc.

2850 Centerville Road

Wilmington, DE 19808-1610

Printed in the USA Feb 2007

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies 4155B Manual de usuario

Agilent Technologies

Agilent Technologies PSA Series Guía de inicio rápido

Agilent Technologies

Agilent Technologies HP 8566B Manual del propietario

Agilent Technologies

Agilent Technologies 8560 E-Series Manual de usuario

Agilent Technologies

Agilent Technologies PNA Series Manual de instalación y operación

Agilent Technologies

Agilent Technologies N3970A Manual de funcionamiento

Agilent Technologies

Agilent Technologies FieldFox N9913A Manual de usuario

Agilent Technologies

Agilent Technologies E5071C Manual de usuario

Agilent Technologies

Agilent Technologies E5052A Manual

Agilent Technologies

Agilent Technologies J2300D Manual de lista de piezas

Agilent Technologies

Agilent Technologies E4915A Manual de usuario

Agilent Technologies

Agilent Technologies J3919A Manual de operación

Agilent Technologies

Agilent Technologies 4284A Guía de instalación

Agilent Technologies

Agilent Technologies X Series Manual de usuario

Agilent Technologies

Agilent Technologies Acqiris DC110 Manual de usuario

Agilent Technologies

Agilent Technologies 6811B Manual de usuario

Agilent Technologies

Agilent Technologies N5225-60114 Manual de instalación y operación

Agilent Technologies

Agilent Technologies PSA Series Manual de instalación y operación

Agilent Technologies

Agilent Technologies ACQIRIS DC122 Manual de usuario

Agilent Technologies

Agilent Technologies Agile or Elusive Signals Using Manual

Agilent Technologies

Agilent Technologies 8614 B Series Manual de usuario

Agilent Technologies

Agilent Technologies MXA Series Manual de instalación y operación

Agilent Technologies

Agilent Technologies PSA Series Manual de usuario

Agilent Technologies

Agilent Technologies 7820A Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario