Agilent Technologies PSA Series Manual de instalación y operación

Installation Note

Part Number E4440-90255

Printed in USA August 2004

Agilent PSA Series Spectrum Analyzers

Option 124 Y-Axis Video Output

Retrofit Kit

Notice.

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including

but not limited to, the implied warranties of merchantability and fitness for a particular

purpose. Agilent Technologies shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or use

of this material.

Installation Note E4440-90255 3

Y-Axis Video Output Installation Kit

Introduction

This installation note explains how to install Option 124, Video Output retrofit kit. The

Option 124 kit is required for newer instruments that have the serial prefix listed above.

These instruments already contain the proper A8 Analog IF assembly, Synthesizer

assembly and rear dress panel to support this retrofit kit.

The retrofit adds a rear panel Y-Axis Video Out connection. The Video Out signal closely

resembles the video out signal on the HP 8566B and 8568B spectrum analyzers. The

video out signal is produced on the special A7 Digital IF assembly, included in the kit,

and sent to a rear panel BNC connector.

NOTE This option is licensed for one instrument model number/serial number

combination. The license key will only install on the designated

instrument.

NOTE The instrument must be performance tested to ensure that the

instrument meets specifications following the hardware installation.

NOTE The instrument firmware revision must be A.06.00 or greater to allow

installation of the license keyword. It is recommended that the

firmware be updated to the latest revision.

See http://www.agilent.com/find/psa_firmware for the latest firmware.

Products Affected: PSA E4440A

PSA E4443A

PSA E4445A

PSA E4446A

PSA E4448A

Serial Numbers: US4430 / US9999

MY4430 / MY999999

For instruments that do not have Option 122.

To Be Performed By: (X) Agilent Service Center

(X) Personnel Qualified by Agilent

( ) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time: 2 Hours

1.5 Hours

4Installation Note E4440-90255

Y-Axis Video Output Installation Kit

Contents

Tools Required

❏T-20 Torx driver

❏T-10 Torx driver

❏9/16-inch nut driver/torque driver

❏PSA Series Performance Tests and Adjustment Software, E.01.00 or later

❏Test equipment supported by the PSA Series Performance Tests and Adjustment

Software.

❏PSA Series Spectrum Analyzer and Service Guide. This manual is available as part of

the E4440AU, E4443AU, or E4445AU Option OBW kits.

❏Microsoft Windows based personnel computer

❏Windows 2000, Windows XP Professional

❏Firmware A.0 6.00 or later. Download the latest revision form

http://www.agilent.com/find/psa_firmware, or order the Firmware Update kit.

Depending on your model number, the firmware update kit is ordered as: Order

E444xAU (Qty.1) Option UE2 (Qty. 1), where the “x” is the last digit of the model

number. For example: E4440AU option UE2.

Quantity Description Agilent Part

Number

1 Installation Note This note

1 A7 Digital IF Assembly E4440-60206

1 W67, Cable, Video Out from Digital IF to rear panel 8121-0964

1 Nut, 15/32 for Video Out BNC connector 0590-2332

1 Washer, internal teeth, 15/32 in. for BNC 2190-0102

1 Option Upgrade Entitlement Certificate ---

1 Getting Started Guide

1 Specification Guide

Installation Note E4440-90255 5

Installation Procedure

Install Firmware A.06.00 or Greater if Needed

1. Press System, More, Show System. The Firmware Revision needs to be A.06.00 or later.

2. If the firmware needs to be updated, do the following:

Download the PSA Update Program and the PSA Firmware Procedure from

http://www.agilent.com/find/psa_firmware. Follow the directions to install the

firmware.

Alternate Method:

Install the Firmware Update Kit E4440AU Option UE2. Follow the directions in the

kit.

Remove the Outer Case

CAUTION If the instrument is placed on its face during any of the following

procedures, be sure to use a soft surface or soft cloth to avoid damage to

the front panel, keys, or input connector.

1. Disconnect the instrument from ac power.

2. Refer to Figure 1. Remove the two handles on the sides of the instrument as shown.

Use the T-20 driver to loosen the screws that attach each handle (1). Remove the

handles.

3. Remove the four bottom feet (2). Lift up on the tabs on the feet, and slide the feet in

the direction indicated by the arrows.

4. Remove the four screws (3) that hold the rear feet (4) in place.

5. Pull the instrument cover (5) off toward the rear of the instrument.

6Installation Note E4440-90255

Installation Procedure

Figure 1 Instrument Outer Case Removal

Installation Note E4440-90255 7

Installation Procedure

Remove the Top Brace

1. Refer to Figure 2. Use the T-10 driver to remove the top screws (3) (one screw is

under the security label), and the side screws (2) attaching the top brace (1) to the

deck.

2. Remove the top brace from the deck.

Figure 2 Top Brace Removal

8Installation Note E4440-90255

Installation Procedure

Installing the Retrofit Kit

1. Refer to Figure 3. Locate the A7 Digital IF Assembly. It is in the forth card slot from

the power supply. This assembly will have casting covers covering the PC board.

Figure 3 A7 Digital IF Assembly

2. Remove the gray flexible coax cable W10 from P1, and remove the A7 Digital IF

assembly from the instrument. Discard this assembly since it will be replaced.

3. Install the A7 Digital IF assembly from the kit. Re-attach the gray cable W10

removed in step 2 to P3. Cable designator “P3”and “GRAY (8)”are silk-screened on

the board.

4. On the instrument rear panel, locate the Video Out hole. Remove the hole plug and

insert the BNC end of W67, BNC to MCX Video Output cable, contained in the kit.

You will be able to insert the BNC connector through the rear frame without

removing the rear dress panel. Install the washer and hex nut, included in the kit,

and torque to 236 Ncm (21 inch pounds). Attach the MCX cable connector to J100 of

the A7 Digital IF assembly.

Installation Note E4440-90255 9

Installation Procedure

Replace the Top Brace and Outer Case

1. Refer to Figure 2. Carefully position the top brace on the deck. The alignment pin at

the center of the web/fan assembly must mate with the alignment hole on the top

brace. Make sure that no coaxial cables will get pinched underneath the brace.

2. Use the T-10 driver to replace and tighten the top screws first; then replace the side

screws. Torque to 101 Ncm (9 in-lb).

3. Refer to Figure 1. Slide the instrument cover back onto the deck from the rear. The

seam on the cover should be on the bottom. Be sure the cover seats into the gasket

groove in the front frame.

4. Replace the four rear feet onto the rear of the instrument. Torque to 236 Ncm (21

in-lb).

5. Use the T-20 driver to replace the handles. Torque to 236 Ncm (21 in-lb).

6. Replace the four bottom feet by pressing them into the holes in the case and sliding

them in the opposite direction of the arrows until they click into place. Note that the

feet at the front have the tilt stands.

10 Installation Note E4440-90255

Installation Procedure

Installing the Option Designator and License Keyword

NOTE The option designator 124 and the license keywordmust be entered into

instrument memory in addition to the correct firmware before the

hardware will function.

1. Follow the directions on the Option Upgrade Entitlement Certificate included in the

kit. A License Key Certificate that contains the license keyword will be e-mailed to

you.

2. Plug in the instrument and power up.

3. On the instrument front panel press: System, More, until the Licensing softkey is

visible. Press Licensing and Option. This will activate the alpha editor menu. Use the

alpha editor and the front panel numerical keypad to enter the option designator 124.

Press the Enter key. Note that 124 now appears on the Option key.

4. Press License Key. The license key number is a hexadecimal number that will require

the entry of both letters and numbers. Use the alpha editor and the front panel

numerical keypad to enter the license key number. Your entry will appear in the

active function area of the display. If you make a typing error, use the backspace key

to correct the error. Check the license key number you entered. Press Enter, Activate

License.

5. Cycle instrument power and allow the instrument to perform the auto align routine.

Press System, More, Show System and verify that 124 appears in the option field.

Otros manuales para PSA Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies E5071C Manual de usuario

Agilent Technologies

Agilent Technologies U1701A Manual de usuario

Agilent Technologies

Agilent Technologies 1670G Series Manual de usuario

Agilent Technologies

Agilent Technologies 5062-8218 Manual de instalación y operación

Agilent Technologies

Agilent Technologies E8364-60102 Manual de instalación y operación

Agilent Technologies

Agilent Technologies 4395A Manual de usuario

Agilent Technologies

Agilent Technologies 4395A Manual de usuario

Agilent Technologies

Agilent Technologies E4440AU Manual de instalación y operación

Agilent Technologies

Agilent Technologies N5225-60114 Manual de instalación y operación

Agilent Technologies

Agilent Technologies NFA Series Manual de uso y cuidado

Agilent Technologies

Agilent Technologies 8753ET Manual de usuario

Agilent Technologies

Agilent Technologies 42841A Manual de usuario

Agilent Technologies

Agilent Technologies E5500A Manual de usuario

Agilent Technologies

Agilent Technologies 8753ES Manual de usuario

Agilent Technologies

Agilent Technologies E4411-60019 Manual de instalación y operación

Agilent Technologies

Agilent Technologies 4285A Manual de usuario

Agilent Technologies

Agilent Technologies 8590L Manual de usuario

Agilent Technologies

Agilent Technologies 8970B Manual de usuario

Agilent Technologies

Agilent Technologies 8510C Manual de usuario

Agilent Technologies

Agilent Technologies PSA Series Manual de instalación y operación

Agilent Technologies

Agilent Technologies 4156b Manual de usuario

Agilent Technologies

Agilent Technologies 53147A Manual de usuario

Agilent Technologies

Agilent Technologies 8753ET Manual de usuario

Agilent Technologies

Agilent Technologies 8719ES Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario