Agilent Technologies G2916A Manual de usuario

Agilent Technologies

Installing a G2916A Sampler Tray on a

5890 Series II Gas Chromatograph

G2916A Kit

This procedure assumes that the Gas Chromatograph (GC) is either

•A 5890A GC which has been fully upgraded to a 5890 Series II instrument

(“fully” means that both electronic and mechanical upgrades have been

performed; a printed circuit board-only upgrade does not qualify).

•ORa 5890 Series II GC which was purchased as such.

and that the G2916-61000 injector bracket has already been installed.

Parts supplied

The kit contents are listed in Table 1.

Tools required

Torx T-20 driver

Preparing the GC

When the sample tray is installed, it blocks access to the pneumatics door on

the left side panel. To maintain easy access to these components, Agilent

recommends the following:

1Remove the GC left side panel.

2Remove the pneumatic compartment access door from the left side panel.

3Reinstall the left side panel.

Table 1 Parts supplied

Part number Description Quantity

18596-40015 Tray quadrants, pkg of 4 1

G2614-60610 Cable, main tray 1

G2916-60000 5890 Tray module 1

0100-1501 Tee, ¼-inch hose, for quadrant temperature control 2

G2916-80510 Tray screw kit. Contains 1

Screw with washer, M4 × 20 mm 4

5128-0714 Screw cap vials, pkg of 100 1

5182-0717 Blue screw caps, pkg of 100 1

G2916-25040 Tray post 1

Installing the tray

1Install the tray post in the hole in the right front corner (as you face the

oven) of the injector bracket (Figure 1).

2Set the tray on the injector bracket so that the frontmost pin on the injector

bracket fits into the mating hole in the bottom of the tray, then align the

tray to the second alignment pin on the injector bracket.

CAUTION Do not move or manipulate the robotic arm or gripper. Moving the arm or gripper back and

forth can cause damage. If necessary, rotate the arm assembly a few degrees until there is

enough clearance.

3Insert four screws with washers where shown. Tighten the screws to secure

the tray to the bracket.

4Install the tray quadrants (Figure 2). Be sure to match the numbers on the

quadrants with the tray base numbers.

Figure 1 Installing the tray

Tray po st

Set tray on this

alignment pin first

Second

alignment pin

5Slide the leading edge of each quadrant under the guides on the tray, then

snap the front tab into the slot on the tray.

6Connect the tray cable from the back of the tray (near the drain fitting) to

the Tray connector on the back of the G2912A Controller.

Figure 2 Install the tray quadrants

Tray quad r ant

Front tab

Guide

Slot

* Tray base numbers

Agilent Technologies

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval

or translation into a foreign language) without prior agreement and written consent from Agilent Technologies,

Inc. as governed by United States and international copyright laws.

G2916-90000

First edition, July 2004

Printed in USA

Agilent Technologies, Inc.

2850 Centerville Road

Wilmington, DE 19808-1610 USA

CAUTION

A CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice,

or the like that, if not correctly performed or adhered to, could result in damage to the prod-

uct or loss of important data. Do not proceed beyond a CAUTION notice until the indicated

conditions are fully understood and met.

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Agilent Technologies

Agilent Technologies

Agilent Technologies 7693A Manual de usuario

Agilent Technologies

Agilent Technologies Cary 8454 Manual de usuario

Agilent Technologies

Agilent Technologies 7200 Manual de usuario

Agilent Technologies

Agilent Technologies 2200 TapeStation Manual de usuario

Agilent Technologies

Agilent Technologies E5850A Manual de usuario

Agilent Technologies

Agilent Technologies 5DX Manual de usuario

Agilent Technologies

Agilent Technologies 4100 Manual de usuario

Agilent Technologies

Agilent Technologies InfinityLab LC Series Manual de usuario

Agilent Technologies

Agilent Technologies GPC/SEC Manual de usuario

Agilent Technologies

Agilent Technologies 7000 Triple Quadrupole GC/MS Manual de usuario

Agilent Technologies

Agilent Technologies 6500 Series Manual de funcionamiento

Agilent Technologies

Agilent Technologies 6460 Manual de usuario

Agilent Technologies

Agilent Technologies Agilent 1260 Infinity Manual de usuario

Agilent Technologies

Agilent Technologies IDP3GBKIT Manual de usuario

Agilent Technologies

Agilent Technologies G1701EA Manual de usuario

Agilent Technologies

Agilent Technologies InfinityLab LC Series Manual de usuario

Agilent Technologies

Agilent Technologies Triple Quadrupole LC/MS Manual de usuario

Agilent Technologies

Agilent Technologies 1260 Infinity Manual de usuario

Agilent Technologies

Agilent Technologies 8860 Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies Pump Module Manual de usuario

Agilent Technologies

Agilent Technologies G5562A Guía de configuración

Agilent Technologies

Agilent Technologies 1100 Series Manual de usuario

Agilent Technologies

Agilent Technologies 7890B Manual de usuario

Agilent Technologies

Agilent Technologies 7890A Guía del usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario

Yamato

Yamato BM510 Manual de usuario