AEMC instruments JM865A Manual de usuario

AC Current Probe

Model JM865A

User Manual

DESCRIPTION

The JM865A (Catalog #2110.88) is designed for use in industrial environments. The

“squared” jaws permit multiple conductor or bus bar positioning. The current output makes

it the perfect tool for measurement with DMMs, recorders, power and harmonic meters.

Three ranges allow you to obtain the best resolution even on low current measurement.

The JM865A is compatible with any AC ammeter, multimeter, or other current measuring

instrument with an input impedance lower than 2 Ω. To achieve the stated accuracy, use the

JM865A with an ammeter with an accuracy of 0.75 % or better.

WARNING

These safety warnings are provided to ensure the safety of personnel and proper operation

of this instrument.

■Read this instruction manual completely and follow all safety information before

attempting to use or service this instrument

■Use caution on any circuit; potentially high voltages and currents may be present and

may pose a shock hazard

■Read the Safety Specications section prior to using the current probe. Never exceed

the maximum voltage ratings given

■Safety is the responsibility of the operator

■ALWAYS connect the current probe to the display device before clamping the probe

onto the sample being tested

■ALWAYS inspect the instrument, probe, probe cable, and output terminals prior to use.

Replace any defective parts immediately

■NEVER use the current probe on electrical conductors rated above 600 V in

overvoltage category III (CAT III). Use extreme caution when clamping around bare

conductors or bus bars

INTERNATIONAL ELECTRICAL SYMBOLS

This symbol signies that the current probe is protected by double or reinforced

insulation. Use only factory-specied replacement parts when servicing the instrument.

This symbol signies CAUTION! The user must refer to the user manual before using

the instrument.

This symbol signies that this is a type A current sensor and that application near and

removal from HAZARDOUS LIVE conductors is permitted.

DEFINITION OF MEASUREMENT CATEGORIES

CAT IV: For measurements performed at the primary electrical supply (<1000 V), such as

primary overcurrent protection devices, ripple control units, or meters.

CAT III: For measurements performed in the building installation at the distribution level,

such as hardwired equipment in xed installation or circuit breakers.

CAT II: For measurements performed on circuits directly connected to the electrical

distribution system, such as household appliances or portable tools.

RECEIVING YOUR SHIPMENT:

Upon receiving your shipment, make sure that the contents are consistent with the packing

list. Notify your distributor of any missing items. If the equipment appears to be damaged,

le a claim immediately with the carrier and notify your distributor at once with a detailed

description of any damage.

CURRENT PROBE - JM865A DRAWING

4.72"

(120 mm)

1.89"

(48 mm)

12.40"

(315 mm)

P1 P2

Ø=2.52" (64 mm)

Cable max.

1.97 x 5.31" (50 x 135 mm) or

2.52 x 3.94" (64 x 100 mm)

Bus Bar max.

Red Black

S2S1

ELECTRICAL SPECIFICATIONS

Current Range:

1 AAC to 1000 AAC continuous cycle

1 AAC to 2000 AAC continuous cycle

1 AAC to 2400 AAC continuous cycle for the

full temperature range

(3000 A, if temperature <95 °F or <35 °C)

Transformation Ratio:

1000:5, 2000:5, 3000:5

Output Signal:

5 mAAC/AAC (5 A at 1000 A)

2.5 mAAC/AAC (5 A at 2000 A)

1.666 mAAC/AAC (5 A at 3000 A)

Accuracy and Phase Shift:*

1000 A RANGE

Primary Current 50 A 200 A 1000 A

Accuracy % 3 % 1.5 % 1 %

Phase shift 3 ° 1.5 ° 1 °

Load Impedance: ≤0.4 Ω

Overload: 1200 A for 10 min

Ampere-Second Product: 15 A·s

Accuracy: Per IEC 185-26-27

Class 1 (2.5 V·A) from 48 Hz to 1000 Hz

Frequency Range:

30 Hz to 5 kHz; current derating above

1 kHz for continuous use.

2000 A RANGE

Primary Current 100 A 400 A 2000 A

Accuracy % 1.5 % 0.75 % 0.5 %

Phase shift 1.5 ° 0.75 ° 0.5 °

Load Impedance: ≤0.4 Ω

Overload: 2400 A for 10 min

Ampere-Second Product: 50 A·s

Accuracy: Per IEC 185-26-27

Class 0.5 (5 V·A) from 48 Hz to 1000 Hz

3000 A RANGE

Primary Current 150 A 600 A 3000 A

Accuracy % 1.5 % 0.75 % 0.5 %

Phase shift 1.5 ° 0.75 ° 0.5 °

Load Impedance: ≤0.4 Ω

Overload: 3600 A for 10 min

Ampere-Second Product: 80 A·s

Accuracy: Per IEC 185-26-27

Class 0.5 (5 V·A) from 48 Hz to 1000 Hz

(*Reference conditions: 23 °C ± 3 K, 20 %RH to

85 %RH, 45 Hz to 65 Hz, external magnetic eld

<40 A/m, no DC component, no external current

carrying conductor, test sample centered.)

Frequency Range: 30 Hz to 1500 Hz; cur-

rent derating above 1500 Hz for continuous

use

Load Impedance: ≤2 Ω

Working Voltage: 600 VAC

Common Mode Voltage: 600 VAC

Inuence of Adjacent Conductor:

<0.005 A/AAC

Inuence of Conductor in Jaw Opening:

1.5 % ± 0.2 A on 1000:5 range

1 % ± 0.2 A on 2000:5 range

1 % ± 0.2 A on 3000:5 range

MECHANICAL SPECIFICATIONS

Operating Temperature:

14 °F to 122 °F (-10 °C to 50 °C)

Storage Temperature:

-13 °F to 176 °F (-25 °C to 80 °C)

Inuence of Temperature:

<0.1 % per 10 K

Jaw Opening: 3.54 in (90 mm)

Maximum Conductor Size:

Cable: 2.52 in Ø max (64 mm)

Bus bar: 1.97 in x 5.31 in (50 mm x 135 mm)

2.52 in x 3.94 in (64 mm x 100 mm)

Envelope Protection:

IP 20 (IEC 529)

Drop Test:

1 m (IEC 68-2-27)

Mechanical Shock:

100 g (IEC 68-2-27)

Vibration:

10/55/10 Hz, 0.15 mm (IEC 68-2-6)

Polycarbonate Material:

Handles: 10 % berglass charged

polycarbonate UL 94 V0

Jaws: ABS UL 94 V2

Dimensions:

4.72 in x 12.40 in x 1.89 in

(120 mm x 315 mm x 48 mm)

Weight:

2.65 lb (1200 g)

Colors:

Dark gray handles with red jaws

Output:

Two standard safety banana jacks (4 mm)

SAFETY SPECIFICATIONS

Electrical:

Double insulation or reinforced insulation

between primary or secondary and outer

case of handle upon IEC 1010-2-32

Common Mode Voltage:

600 V CAT III, Pollution: 2

ORDERING INFORMATION

Current Probe JM865A........ Cat. #2110.88

Accessories:

Adapter - Banana (Female) to BNC (Male)

(XM-BB) (600 V CAT III) ........ Cat. #2118.46

Lead - set of 2, 5 ft (red/black) PVC

with 4 mm ST/ST plugs .........Cat. #5100.07

OPERATION

Please ensure that you have read and fully understand the WARNING section on page 1.

Making Measurements with the AC Current Probe Model JM865A

■Connect the black and red terminals to the Ampere AC range of your DMM or current

measuring instrument. Select the appropriate current range. If the current magnitude

is unknown, select the highest range (3000 AAC / 5 AAC) on the switch probe inside

the handle. Clamp the probe around the conductor with the arrow pointed toward the

load. Select the lower range until you obtain the best resolution. Read the value display

on the DMM and multiply it by the range selected. If the reading equals 2.59 A on the

1000/5 range, the current owing through the probe is 518 AAC (2.59 A x 200).

■For the best accuracy, carefully center the conductor inside the probe jaw, avoid if

possible, the proximity of other conductors which may create noise.

Tips for Making Precise Measurements

■When using a current probe with a meter, it is important to select the range that provides

the best resolution. Failure to do this may result in measurement errors.

■Make sure that probe jaw mating surfaces are free of dust and contamination.

Contaminants cause air gaps between the jaws, increasing the phase shift between

primary and secondary. It is very critical for power measurement.

MAINTENANCE

Warning:

■For maintenance use only original factory replacement parts.

■To avoid electrical shock, do not attempt to perform any servicing unless you are

qualied to do so.

■To avoid electrical shock and/or damage to the instrument, do not get water or other

foreign agents into the probe.

Cleaning:

To ensure optimum performance, it is important to keep the probe jaw mating surfaces clean at

all times. Failure to do so may result in error in readings. To clean the probe jaws, use very ne

sand paper (ne 600) to avoid scratching the jaw, then gently clean with a soft oiled cloth.

REPAIR AND CALIBRATION

You must contact our Service Center for a Customer Service Authorization number

(CSA#). This will ensure that when your instrument arrives, it will be tracked and processed

promptly. Please write the CSA# on the outside of the shipping container.

Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments

15 Faraday Drive

Dover, NH 03820 USA

Phone: (800) 945-2362 (Ext. 360)

(603) 749-6434 (Ext. 360)

Fax: (603) 742-2346 or (603) 749-6309

E-mail: [email protected]

(Or contact your authorized distributor)

NOTE: All customers must obtain a CSA# before returning any instrument.

TECHNICAL AND SALES ASSISTANCE

If you are experiencing any technical problems, or require any assistance with the proper

use or application of this instrument, please contact our technical hotline:

Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments

15 Faraday Drive

Dover, NH 03820 USA

Phone: (800) 343-1391 (Ext. 351)

Fax: (603) 742-2346

E-mail: [email protected]

LIMITED WARRANTY

The current probe is warrantied to the owner for a period of two years from the date of

original purchase against defects in manufacture. This limited warranty is given by AEMC®

Instruments, not by the distributor that it was purchased from. This warranty is void if the

unit has been tampered with, abused, or if the defect is related to service not performed by

AEMC®Instruments.

Full warranty coverage and product registration is available on our website at:

www.aemc.com/warranty.html.

Please print the online Warranty Coverage Information for your records.

99-MAN 100125.v9 08/22

Este manual sirve para los siguientes modelos

Otros manuales de Instrumento de medición de AEMC instruments

AEMC instruments

AEMC instruments 6536 Manual de usuario

AEMC instruments

AEMC instruments K100 Manual de usuario

AEMC instruments

AEMC instruments MA194-24-BK Manual de usuario

AEMC instruments

AEMC instruments MN01 Manual de usuario

AEMC instruments

AEMC instruments MN375 Manual de usuario

AEMC instruments

AEMC instruments PEL 105 Manual de usuario

AEMC instruments

AEMC instruments MN379T Manual de usuario

AEMC instruments

AEMC instruments Digital FlexProbes 400D-10 Manual de usuario

AEMC instruments

AEMC instruments MR525 Manual de usuario

AEMC instruments

AEMC instruments MN290 Manual de usuario

AEMC instruments

AEMC instruments Measure Up PowerPad III Manual de usuario

AEMC instruments

AEMC instruments JM835A Manual de usuario

AEMC instruments

AEMC instruments 5050 Manual de usuario

AEMC instruments

AEMC instruments CA811 Manual de usuario

AEMC instruments

AEMC instruments SR759 Manual de usuario

AEMC instruments

AEMC instruments OX5042 Manual de usuario

AEMC instruments

AEMC instruments 6292 Manual de usuario

AEMC instruments

AEMC instruments JM852 Manual de usuario

AEMC instruments

AEMC instruments MN185 Manual de usuario

AEMC instruments

AEMC instruments A196-24-BK Manual de usuario

AEMC instruments

AEMC instruments 1035 Manual de usuario

AEMC instruments

AEMC instruments MN125 Manual de usuario

AEMC instruments

AEMC instruments CA7027 Manual de usuario

AEMC instruments

AEMC instruments MD303 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario