AEMC instruments 6536 Manual de usuario

WITH AEMC

INSTRUMENTS

MEGOHMMETERS

Megohmmeter

Model 6536

ENGLISH

User Manual

No part of this documentation may be reproduced in any form or by any means (including electronic

storage and retrieval or translation into any other language) without prior agreement and written consent

from Chauvin Arnoux®, Inc., as governed by United States and International copyright laws.

Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments

15 Faraday Drive • Dover, NH 03820 USA

Tel: (800) 945-2362 or (603) 749-6434 • Fax: (603) 742-2346

This documentation is provided “as is,” without warranty of any kind, express, implied, or otherwise.

Chauvin Arnoux®󰀨

but does not warrant the accuracy or completeness of the text, graphics, or other information contained

in this documentation. Chauvin Arnoux®, Inc. shall not be liable for any damages, special, indirect,





user of the documentation has been advised of the possibility of such damages.

Chauvin Arnoux®, Inc.

d.b.a AEMC®Instruments

www.aemc.com

Statement of Compliance

Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments



using standards and instruments traceable to

international standards.

We guarantee that at the time of shipping your

instrument has met the instrument’s published



An NIST traceable certicate may be requested

at the time of purchase, or obtained by returning

the instrument to our repair and calibration

facility, for a nominal charge.

The recommended calibration interval for this

instrument is 12 months and begins on the date of

receipt by the customer. For recalibration, please

use our calibration services. Refer to our repair and

calibration section at www.aemc.com/calibration.

Serial #:

Catalog #: 2155.56

Model #: 6536

ll in the appropriate date as indicated:

Date Received:

Date Calibration Due:

TABLE OF CONTENTS

1. INTRODUCTION..................................................................6

1.1 PRECAUTIONS FOR USE ........................................................ 8

1.2 RECEIVING YOUR SHIPMENT................................................ 9

1.3 ORDERING INFORMATION: .................................................... 9

Shipping Contents: ...................................................................... 9

1.3.1 Accessories ...................................................................... 10

1.3.2 Replacement Parts........................................................... 10

2. PRODUCT FEATURES..................................................... 11

2.1 DESCRIPTION ......................................................................... 11

2.2 FRONT OF INSTRUMENT...................................................... 12

2.3 BACK OF INSTRUMENT ........................................................ 13

2.4 TERMINALS ............................................................................. 14

2.5 FUNCTION BUTTONS ............................................................ 14

2.6 L C D DISPL AY .......................................................................... 15

3. OPERATION ...................................................................... 16

3.1 SETTING UP THE INSTRUMENT.......................................... 16

....................................................... 16

3.1.2 Alarms............................................................................... 17

3.1.2.1 Activating/Deactivating the Alarm Function............... 17

3.1.2.2 Setting an Alarm Threshold ...................................... 18

3.1.2.3 Viewing Alarms.......................................................... 18

.................................................................. 19

3.1.4 HOLD Function ................................................................. 20

3.1.5 Backlighting ...................................................................... 20

3.1.6 Standby Mode................................................................... 21

3.2 TAKING MEASUREMENTS.................................................... 21

3.2.1 Voltage Measurement....................................................... 21

3.2.2 Insulation Measurement................................................... 22

3.2.2.1 TEST Button Operation............................................. 24

3.2.2.2 Timed Tests ............................................................. 24

3.2.2.3 Remote Control Probe (Optional) ............................. 25

3.2.3 Continuity Measurement .................................................. 26

3.2.3.1 Lead Compensation.................................................. 26

3.2.3.2 Continuity Measuring................................................ 27

3.2.4 Resistance Measurement ................................................ 28

3.2.5 Floor Resistance Testing.................................................. 29

3.2.5.1 Setup ......................................................................... 30

3.2.5.2 Test Procedure.......................................................... 30

3.2.5.3 Measurement Results............................................... 31

4. SPECIFICATIONS ............................................................. 32

4.1 GENERAL REFERENCE CONDITIONS................................ 32

4.2 ELECTRICAL SPECIFICATIONS........................................... 32

4.2.1 Voltage Measurement....................................................... 32

4.2.2 Insulation Measurement................................................... 32

4.2.3 Continuity Measurement .................................................. 34

4.2.4 Resistance Measurement................................................. 35

4.2.5 Timer ................................................................................ 35

4.2.6 Floor Resistance Testing.................................................. 35

4.3 OPERATING ENVIRONMENT................................................ 35

4.3.1 Voltage Measurement....................................................... 35

4.3.2 Insulation Measurement................................................... 36

4.3.3 Resistance and Continuity Measurement ........................ 37

4.3.4 Intrinsic Uncertainty and Operating Uncertainty .............. 37

4.4 POWER SUPPLY ..................................................................... 38

4.5 ENVIRONMENTAL CONDITIONS ......................................... 38

4.6 MECHANICAL SPECIFICATIONS ........................................ 38

4.7 SAFET Y STANDARDS ............................................................ 38

5. MAINTENANCE & TROUBLESHOOTING......................39

5.1 M A I N T E N A N C E ....................................................................... 39

5.1.1 Cleaning ............................................................................ 39

5.1.2 Replacing the Batteries..................................................... 39

5.2 TROUBLESHOOTING............................................................. 41

5.2.1 Errors................................................................................ 41

5.2.1.1 Voltage present before an insulation measurement.....41

5.2.1.2 Range exceeded during an insulation measurement ..41

5.2.1.3 Voltage present during a continuity or resistance

measurement .........................................................................41

5.2.2 Resetting the Instrument .................................................. 42

5.3 REPAIR AND CALIBRATION ................................................. 42

5.4 TECHNICAL AND SALES ASSISTANCE .............................. 42

5.5 LIMITED WARRANTY............................................................. 43

5.5.1 Warranty Repairs.............................................................. 43

Megohmmeter Model 6536

1. INTRODUCTION

Thank you for purchasing an AEMC®Instruments Megohmmeter Model 6536.

For the best results from your instrument and for your safety, you must read the

enclosed operating instructions carefully and comply with the precautions for use.



Symbols and Denitions



CAUTION - Risk of Danger! Indicates a WARNING. Whenever this symbol

is present, the operator must refer to the user manual before operation

Indicates a risk of electric shock. The voltage at the parts marked with this

symbol may be dangerous

Indicates Important information to acknowledge

Ground/Earth

Battery

> 700V The voltage on the terminals must not exceed 700 V

Remote test probe

This product complies with the Low Voltage & Electromagnetic Compatibility

European directives (73/23/CEE & 89/336/CEE)

The 



Electromagnetic Compatibility, and the Restriction of Hazardous Substances

The product has been declared recyclable

Chauvin Arnoux®and AEMC®Instruments have adopted an Eco-Design

approach in order to design this instrument. Analysis of the complete life-

󰀨

environment. In particular this instrument exceeds regulation requirements

with respect to recycling and reuse

In the European Union, this product is subject to a separate collection

system for recycling electrical and electronic components in accordance with

directive WEEE 2002/96/EC

Megohmmeter Model 6536

Denition of Measurement Categories (CAT)

CAT IV: Corresponds to measurements performed at the primary electrical

supply (< 1000 V).

Example: primary overcurrent protection devices, ripple control units,

and meters.

CAT III: Corresponds to measurements performed in the building installation

at the distribution level.

Example: hardwired equipment in xed installation and circuit breakers.

CAT II: Corresponds to measurements performed on circuits directly

connected to the electrical distribution system.

Example: measurements on household appliances and portable tools.

Megohmmeter Model 6536

1.1 PRECAUTIONS FOR USE

This instrument is compliant with safety standard IEC 61010-2-030, and the leads are

compliant with IEC 61010-031, for voltages up to 600 V in CAT IV or 1000 V in CAT III.

Failure to observe the following safety instructions may result in electric shock,



 

 

 

protection features.

 

responsibility of the integrator of the system.

 

exceeding 600 VRMS with respect to ground or 700 VRMS maximum

between terminals.

 



 

 

“live” systems.

 

closed.

 

housing, and accessories. Any part on which the insulation is deteriorated

(even partially) must be set aside for repair or scrapping.

 

electric shock to the user.

 

 

accessories) of a lower voltage rating or category limits the use of the

instrument/leads (or accessories) combination to the lowest category and

service voltage.

 

behind the physical guards.

 

leads and accessories are disconnected. Replace all batteries at once. Use

alkaline batteries.

 

 

accredited personnel.

Megohmmeter Model 6536

1.2 RECEIVING YOUR SHIPMENT

Upon receiving your megohmmeter product package, ensure the contents are

consistent with the packing list. Notify your distributor of any missing items. If



and notify your distributor at once, providing a detailed description. Save the

damaged packing container to substantiate your claim.

1.3 ORDERING INFORMATION:

Megohmmeter Model 6536..............................................................Cat. #2155.56

Megohmmeter Model 6536 ESD Floor Kit...................................... Cat. #2155.57

Shipping Contents:

ESD Floor Kit

(only with Cat. #2155.57)

Megohmmeter Model 6536

(1) Soft Carrying Pouch - Cat. #2119.02

7.75 x 9.25 x 2.75 in

Two color-coded (red/black) 1.5 m test leads,

two alligator clips, two grip probes and

one test probe (black)

Megohmmeter Model 6536

1.3.1 Accessories

Megohmmeter Test Probe (600 V CAT IV) ......................................Cat. #2155.75

Case - Field Case (Waterproof - Replacement for ESD Floor Kit).......Cat. #2155.77

Continuity Probe...............................................................................Cat. #2138.54

Probe – red test probe (1000 V Cat IV, 15 A, UL)............................Cat. #5000.31

1.3.2 Replacement Parts

Carrying Pouch for Cable Tester, Megohmmeters,

Multimeters, etc................................................................................Cat. #2119.02

Probe - Set of 2, Color-coded (Red/Black) Grip Probes................. Cat. #2152.26

Probe – Black test probe (1000 V Cat IV, 15 A, UL) ........................Cat. #5000.30

Lead - Set of 2, 5 ft silicone color-coded (red/black) with

4 mm straight/right banana plugs (Rated 1000 V, CAT IV, UL) .......Cat. #5000.94

 ....Cat. #5000.97

Clip - Safety Alligator - Black (1000 V CAT IV, 15 A, UL V2) ..........Cat. #5000.99

Clip - Safety Alligator - Red (1000 V CAT IV, 15 A, UL V2) ............Cat. #5100.00

Weights - Set of 2, 5 lbs each with conductive rubber

bottom pad (RoHS) ..........................................................................Cat. #2155.76

Adapter - 4 mm non-insulated for safety leads

(Replacement for ESD Floor Kit)......................................................Cat. #1017.45

Order Accessories and Replacement Parts Directly Online

Check our Storefront at www.aemc.com/store for availability

Otros manuales para 6536

Tabla de contenidos

Otros manuales de Instrumento de medición de AEMC instruments

AEMC instruments

AEMC instruments MN09 Manual de usuario

AEMC instruments

AEMC instruments MR525 Manual de usuario

AEMC instruments

AEMC instruments Measure Up PowerPad III Manual de usuario

AEMC instruments

AEMC instruments 6550 Manual de usuario

AEMC instruments

AEMC instruments MN185 Manual de usuario

AEMC instruments

AEMC instruments 1510 Manual de usuario

AEMC instruments

AEMC instruments 5070 Manual de usuario

AEMC instruments

AEMC instruments SL261 Manual de usuario

AEMC instruments

AEMC instruments 6501 Manual de usuario

AEMC instruments

AEMC instruments MN261 Manual de usuario

AEMC instruments

AEMC instruments AmpFlex 193-24-BK Manual de usuario

AEMC instruments

AEMC instruments 6550 Manual de usuario

AEMC instruments

AEMC instruments JM852 Manual de usuario

AEMC instruments

AEMC instruments 6528 Manual de usuario

AEMC instruments

AEMC instruments MN375 Manual de usuario

AEMC instruments

AEMC instruments DIGITAL FLEXPROBE 400D-6 Manual de usuario

AEMC instruments

AEMC instruments MD304 Manual de usuario

AEMC instruments

AEMC instruments FlexProbe 24-3001 Manual de usuario

AEMC instruments

AEMC instruments MN379T Manual de usuario

AEMC instruments

AEMC instruments MD305 Manual de usuario

AEMC instruments

AEMC instruments SR759 Manual de usuario

AEMC instruments

AEMC instruments OX5042 Manual de usuario

AEMC instruments

AEMC instruments Simple Logger AmpFlex AL24-2500 Manual de usuario

AEMC instruments

AEMC instruments 6292 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario