Advantech PCI-1752U Manual de usuario

PCI-1752U

Isolated Digital Output Card

User Manual

PCI-1752 User Manual ii

The documentation and the software included with this product are copy-

righted 2005 by Advantech Co., Ltd. All rights are reserved. Advantech

Co., Ltd. reserves the right to make improvements in the products

described in this manual at any time without notice. No part of this man-

ual may be reproduced, copied, translated or transmitted in any form or

by any means without the prior written permission of Advantech Co., Ltd.

Information provided in this manual is intended to be accurate and reli-

able. However, Advantech Co., Ltd. assumes no responsibility for its use,

nor for any infringements of the rights of third parties, which may result

from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows and MS-DOS are registered trademarks of

Microsoft Corp.

All other product names or trademarks are properties of their respective

owners.

Part No. 2003175200 1st Edition

Printed in Taiwan February 2006

iii

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its prod-

ucts will be free from defects in materials and workmanship for two years

from the date of purchase.

This warranty does not apply to any products which have been repaired or

altered by persons other than repair personnel authorized by Advantech,

or which have been subject to misuse, abuse, accident or improper instal-

lation. Advantech assumes no liability under the terms of this warranty as

a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous test-

ing, most of our customers never need to use our repair service. If an

Advantech product is defective, it will be repaired or replaced at no

charge during the warranty period. For out-of-warranty repairs, you will

be billed according to the cost of replacement materials, service time and

freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For

example, CPU speed, Advantech products used, other hardware

and software used, etc.) Note anything abnormal and list any

onscreen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your man-

ual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return

merchandise authorization) number from your dealer. This allows

us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and

Replacement Order Card and a photocopy proof of purchase date

(such as your sales receipt) in a shippable container. A product

returned without proof of the purchase date is not eligible for war-

ranty service.

5. Write the RMA number visibly on the outside of the package and

ship it prepaid to your dealer.

PCI-1752 User Manual iv

Declaration of Conformity

This product has passed the CE test for environmental specifications

when shielded cables are used for external wiring. We recommend the use

of shielded cables. This kind of cable is available from Advantech. Please

contact your local supplier for ordering information.

This product has passed the CE test for environmental specifications. Test

conditions for passing included the equipment being operated within an

industrial enclosure. In order to protect the product from being damaged

by ESD (Electrostatic Discharge) and EMI leakage, we strongly recom-

mend the use of CE-compliant industrial enclosure products.

FCC Class A

Note: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Opera-

tion of this equipment in a residential area is likely to cause harmful inter-

ference in which case the user will be required to correct the interference

at his own expense.

FCC Class B

Note: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The PCI-1752U/PCI-1752USO have passed the FM certification.

According to the National Fire Protection Association, work sites are

classified into different classes, divisions and groups, based on hazard

considerations. PCI-1752U/PCI-1752USO are compliant with the specifi-

cations of Class I, Division 2, Groups A, B, C and D indoor hazards.

Technical Support and Assistance

Step 1. Visit the Advantech web site at www.advantech.com/support

where you can find the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, appli-

cation software, etc.)

- A complete description of the problem

- The exact wording of any error messages

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning.

Use a damp cloth. Do not use liquid or spray detergents for clean-

ing.

4. For plug-in equipment, the power outlet socket must be located

near the equipment and must be easily accessible.

5. Keep this equipment away from humidity.

PCI-1752 User Manual vi

6. Put this equipment on a reliable surface during installation. Drop-

ping it or letting it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before con-

necting the equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not

place anything over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the

power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or elec-

trical shock.

13. Never open the equipment. For safety reasons, the equipment

should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked

by service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work

according to the user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT

WHERE THE STORAGE TEMPERATURE MAY GO BELOW -

20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAM-

AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A

CONTROLLED ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS

INCORRECTLY REPLACED. REPLACE ONLY WITH THE

SAME OR EQUIVALENT TYPE RECOMMENDED BY THE

MANUFACTURER, DISCARD USED BATTERIES ACCORD-

ING TO THE MANUFACTURER'S INSTRUCTIONS.

The sound pressure level at the operator's position according to IEC 704-

1:1982 is no more than 70 dB (A).

vii

DISCLAIMER: This set of instructions is given according to IEC 704-1.

Advantech disclaims all responsibility for the accuracy of any statements

contained herein.

Wichtige Sicherheishinweise

1. 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Ver-

wenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient

ein angefeuchtetes Tuch zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und

leicht zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.

Ein Kippen oder Fallen könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät

vor überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen

nicht abgedeckt werden.

8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBw-

erte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber

fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind

zu beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten

Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspan-

nung eine Beschädigung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder

Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw.

elektrischen Schlag auslösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der ele-

ktrischen Sicherheit nur von authorisiertem Servicepersonal geöff-

net werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz

zu trennen und von einer qualifizierten Servicestelle zu überprüfen:

a - Netzkabel oder Netzstecker sind beschädigt.

PCI-1752 User Manual viii

b - Flüssigkeit ist in das Gerät eingedrungen.

c - Das Gerät war Feuchtigkeit ausgesetzt.

d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funk-

tioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erz-

ielen.

e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der

Batterie.Ersatz nur durch densellben order einem vom Hersteller

empfohlene-mahnlichen Typ. Entsorgung gebrauchter Batterien

navh Angaben des Herstellers.

16. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf

nicht fach-männische Weise gewechselt wird. Verfangen Sie die

Batterie nur gleicher oder entsprechender Type, wie vom Hersteller

empfohlen. Entsorgen Sie Batterien nach Anweisung des Herstell-

ers.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000

beträgt 70dB(A) oder weiger.

Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend

der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die

Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab.

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the

products from damage.

1. To avoid electrical shock, always disconnect the power from your

PC chassis before you work on it. Don't touch any components on

the CPU card or other cards while the PC is on.

2. Disconnect power before making any configuration changes. The

sudden rush of power as you connect a jumper or install a card may

damage sensitive electronic components.

ix Table of Contents

Contents

Chapter 1 Introduction ..................................................... 2

1.1 Features ............................................................................ 2

Figure 1.1:Installation Flow Chart ................................. 4

1.2 Installation Guide .............................................................. 5

1.3 Accessories........................................................................ 5

Chapter 2 Installation ....................................................... 8

2.1 Unpacking ......................................................................... 8

2.2 Driver Installation ............................................................. 9

Figure 2.1: Advantech Automation Software Setup ...... 9

2.3 Hardware Installation ..................................................... 10

Figure 2.2:Device name listed on Device Manager ..... 11

2.4 Device Setup & Configuration........................................ 12

Figure 2.3:Device Setting dialog box of PCI-1752 ..... 12

2.5 Device Testing................................................................. 12

Figure 2.4:Advantech Device Manager ....................... 13

Figure 2.5:Digital Output in Device Test dialog box .. 14

Chapter 3 Signal Connections ........................................ 16

3.1 I/O Connector Pin Assignment ....................................... 16

3.2 Location of Jumpers and DIP switch .............................. 16

Figure 3.1:I/O Connector Pin Assignments ................. 17

Table 3.1:I/O Connector Signal Descriptions .............. 18

Figure 3.2:Location of Jumpers and DIP switch ......... 19

3.3 Isolated Digital Output Connections............................... 19

Table 3.2:Power on configuration after hot reset ........ 19

Figure 3.3:Isolated DO: PCI-1752U (sink type) .......... 20

Figure 3.4:Isolated DO: PCI-1752USO (source type) . 20

3.4 Field Wiring Considerations ........................................... 21

Chapter 4 Operation ....................................................... 24

4.1 Board ID.......................................................................... 24

Table 4.1:Board ID register ......................................... 24

Table 4.2:Board ID setting ........................................... 24

Figure 4.1:Device # and board ID on dialog box ....... 25

4.2 Channel-Freeze Function ................................................ 25

Table 4.3:JP2: Channel-Freeze function input mode ... 26

Figure 4.2:Wiring in wet/dry contact input mode ........ 26

Table 4.4:Channel-Freeze function register ................. 26

Table 4.5:Channel-Freeze function bit value ............... 27

Appendix A Specifications ................................................. 30

Table A.1:Isolated Digital Output ............................... 30

Table A.2:General Specifications ................................ 30

Appendix B Block Diagram............................................... 32

Appendix C Register Structure & Format....................... 34

PCI-1752 User Manual x

C.1 Overview ......................................................................... 34

C.2 I/O Port Address Map ..................................................... 34

C.3 PCI-1752 Register Format .............................................. 35

Appendix D ADAM-3951 Pin Assignments...................... 38

Otros manuales para PCI-1752U

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de Advantech

Advantech

Advantech MIO-2375 Manual de instalación y operación

Advantech

Advantech MIC-75M20 Manual de instalación y operación

Advantech

Advantech MIO-5376 Manual de instalación y operación

Advantech

Advantech AIMB-278 Manual de usuario

Advantech

Advantech POS-761F Manual de usuario

Advantech

Advantech PCE-2033 Manual de usuario

Advantech

Advantech PCE-5133 Manual de instalación y operación

Advantech

Advantech HPC-8000 Manual de usuario

Advantech

Advantech PCA-6751 Series Manual de usuario

Advantech

Advantech PCL-848A/B Manual de usuario

Advantech

Advantech MIO-5270 Manual de instalación y operación

Advantech

Advantech MIC-7 Series Manual de instalación y operación

Advantech

Advantech PCA-6276 Manual de usuario

Advantech

Advantech PCIE-1158 Manual de instalación y operación

Advantech

Advantech PCA-6119P7 Manual de instalación y operación

Advantech

Advantech SOM-MZ10 Manual de instalación y operación

Advantech

Advantech UNO-238 V2 Manual de usuario

Advantech

Advantech PCE-7B13-0AA1 Manual de instalación y operación

Advantech

Advantech PCLD-8811 Manual de instalación y operación

Advantech

Advantech RSB-3720 Manual de usuario

Advantech

Advantech PCE-5B12-07 Manual de instalación y operación

Advantech

Advantech UNO-2484G Manual de usuario

Advantech

Advantech AIMB-592 Manual de usuario

Advantech

Advantech ASMB-610V3 Manual de instalación y operación

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario